I’m not sold on the need for a power jointer for flattening a surface. That said, I do have a Shopsmith 4″ jointer.. It’s great for jointing edges, and perhaps flattening the occasional rails and stiles, but it of course is inadequate for surfacing wide boards. Would a six inch jointer be better…..not by much. So what do we do? Go to an eight inch, or better yet a ten inch jointer? Now we’re getting into really big, heavy, and electrically hungry machines that are not really suitable for the small shop that is likely to be in a small shed or garage.
There are no formal education or training requirements to become a carpenter in the U.S., but the BLS reports that three to four years of experience is the industry standard for becoming a skilled craftsperson. Training and experience can be acquired by working with an experienced journeyman or through an apprenticeship offered by an employer or labor union. Formal in-class instruction is offered through certificate, diploma or associate's degree programs in carpentry at trade or vocational schools. Employees with some formal carpentry education generally start at higher positions in the field. Carpentry courses may include carpentry math, building layouts, foundation work, roofing, stair construction, siding and moldings. You can also study interior and exterior finishes.
The field of carpentry offers many opportunities for employment and advancement for workers with solid educational backgrounds and training. As work and educational experiences enhance your skill sets, you may earn the chance to advance to more responsibility and a higher salary. For example, you could be promoted to a general construction supervisor position within a larger construction company.
The Amish here in Ohio use a nifty wooden rule for calculating bd. ft. It has a brass football shaped hook on the end and they’re about 2′ long. Three columns of numbers run down the length of stick. These columns are the length of stock say, 12,14,16 foot. Within these columns, bd. ft. has already been calculated and marked. For a 16′ bd. the hook is placed over one edge and a reading of bd. ft. is taken from opposite edge from the 16′ column. “Audels Carpenters and Builders Guide #1” pg. 146, shows a good example. They call… Read more »
Even though this is in fact a side table, we can definitely find inspiration in its design. We find this project to be highly creative and interesting. The table has a hexagon-shaped top and bottom connected by two sets of five rods. Two in each set are longer than the other and go through the bottom hexagon, acting as legs. You can find the plans for this project on ohohblog.

Hardwoods come from deciduous, or broad-leaved trees, as opposed to softwoods, that are harvested from from evergreens. In general, the lumber derived from hardwood species are typically harder than softwoods, although there are exceptions (balsa wood is very light and soft, but is considered a hardwood). Most hardwood tree species lose their leaves in winter, and generally offer a much wider variety of colors and textures than softwoods. Typically, stock from hardwood species are a lot more expensive than those from softwoods.


Description: In this four day class, we will start with rough lumber and finish with a simple box. Along the way we will teach you how to use the jointer, planer, table saw, and router table This is THE class to take if you are interested in getting started the right way in woodworking. This one will fill up fast, so sign up. soon. Woodworking 101 is strongly recommended for beginners and people looking to review the basics.
Framing is another part of carpentry. Framing takes skill and experience it’s not a part of carpentry that anyone can just jump into. The skills that are required in framing is plumbing up a wall, make sure studs are 16 on center or whatever the specs calls for. Developing a good eye for straightness in carpentry work. Last but not least making sure everything is level.
Thread Related Link and Image Guidelines Thread Related Links posted at WOODWEB's Forums and Exchanges should point to locations that provide supporting information for the topic being discussed in the current message thread. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related Link that directs visitors to an area with inappropriate content will be removed. WOODWEB reserves the right to delete any messages with links or images it deems inappropriate. (return to form)
The Amish here in Ohio use a nifty wooden rule for calculating bd. ft. It has a brass football shaped hook on the end and they’re about 2′ long. Three columns of numbers run down the length of stick. These columns are the length of stock say, 12,14,16 foot. Within these columns, bd. ft. has already been calculated and marked. For a 16′ bd. the hook is placed over one edge and a reading of bd. ft. is taken from opposite edge from the 16′ column. “Audels Carpenters and Builders Guide #1” pg. 146, shows a good example. They call… Read more »
You might not see these tables very often but they were relied on by sheep farmers for many years. Anything that could make the job of shearing sheep easier was welcomed on the farm. You could even change up the plan a little bit by making the legs longer and adding steel (or wooden) wheels to make a merchants cart. That latter idea is something we are suggesting, its not a part of this plan. Joinery methods used primarily in the construction of this sturdy table include mortise and tenon and tongue and groove. View the Larger Image Slideshow to see the actual paper plan you are buying.

Dan, my work space that is available for power tools is quite small, about 6′ x 20′. It may seem like a lot on the surface, but a long rectangle is a bear to work in. It requires a lot of serpentine action. That said, I don’t have too much room for large footprint tools. I have settled finally on three big tools; a small bench saw, a thickness planer, and a drill press. I had to forgo the jointer, so I use hand tools to make up for it’s absence (as I do with a lot of my hand tool techniques). I have gotten to the point where I can flatten one side and true an edge of a board reasonably quick. I then finish it up with the thickness planer and table saw, giving me a nice flat board. I guess what I am basically saying is, there’s more than one way to skin a cat, and don’t write off hand tools as a quaint way to experience the past. They worked for thousands of years, and still do! Thanks for the blogs, they make for great reading.
Description: When you have reached that point in your turning, where you are ready to challenge yourself with something new, this class will teach you some proven techniques for turning simple hollow forms. Students will have the opportunity to use a variety of turning tools and hollowing tools. You will also learn sharpening techniques for these tools. We will also discuss design options and aesthetics, and learn various finishing techniques. All students are encouraged to bring their favorite turning tools to use on this project.
There are no formal education or training requirements to become a carpenter in the U.S., but the BLS reports that three to four years of experience is the industry standard for becoming a skilled craftsperson. Training and experience can be acquired by working with an experienced journeyman or through an apprenticeship offered by an employer or labor union. Formal in-class instruction is offered through certificate, diploma or associate's degree programs in carpentry at trade or vocational schools. Employees with some formal carpentry education generally start at higher positions in the field. Carpentry courses may include carpentry math, building layouts, foundation work, roofing, stair construction, siding and moldings. You can also study interior and exterior finishes.
Hardwoods come from deciduous, or broad-leaved trees, as opposed to softwoods, that are harvested from from evergreens. In general, the lumber derived from hardwood species are typically harder than softwoods, although there are exceptions (balsa wood is very light and soft, but is considered a hardwood). Most hardwood tree species lose their leaves in winter, and generally offer a much wider variety of colors and textures than softwoods. Typically, stock from hardwood species are a lot more expensive than those from softwoods.
Every woodworker needs a couple of levels. You probably won’t need one of the 6-foot levels used in construction, but 48” is a good length for many of the woodworking projects you’ll do. Usually, you’ll also need an 8” level too, usually known as a torpedo level. You’ll check the level and plum of your construction. Level means horizontal, and plumb is vertical.
Even though this is in fact a side table, we can definitely find inspiration in its design. We find this project to be highly creative and interesting. The table has a hexagon-shaped top and bottom connected by two sets of five rods. Two in each set are longer than the other and go through the bottom hexagon, acting as legs. You can find the plans for this project on ohohblog.
Let’s start with perhaps the most basic tool in every household – the claw hammer. The claw on one side of the head should be well counterbalanced by the finished head, which should be somewhat rounded. The other kind of head is the waffle-head. Most commonly used in construction, it leaves a distinctive waffle mark on the wood when you drive the nail. This, of course, is not the proper nail for woodworking.
Don’t let the angles on this table scare you away–the design is actually very simple! Just adjust your miter saw from zero to seven degrees for a few of the cuts, and you can create the splayed legs on this basic coffee table. And with the addition of blocks to the front of the legs, it’s easy to fake the look of advanced mortise and tenon joinery. Read on to see how the parts come together.
Concrete is one part of basic carpentry. The concrete part of carpentry has to deal with building forms that are going to hold concrete its just that simple. There are different ways to build forms for example, with Symons forms, plywood and 2 by 4's and much more. This is the easiest part of carpentry in my opinion. The toughest part in this area is the weather most of the time the work in this area is outside.

Screwdrivers are another must-have in the woodworker’s set of hand tools. Not only will you need Phillips and slot, or flathead screwdrivers, you’ll need star drivers and Torx drivers, too. A quality construction is vital to a good set of screwdrivers. So many of them are made out of soft metal, and the first time you put any “oomph” behind them, they strip out, becoming absolutely useless.


You might be able to enroll in a General Contractor's License Preparation Certificate, a Carpentry Diploma or a Career Diploma in Carpentry program, among other options. Programs might require a high school diploma or its equivalent and a placement test. The programs may prepare you for entry-level positions in industry, engineering and the construction trades. The following topics might be covered in a carpentry or contracting program:

Using wood glue and 1 1/4" pocket hole screws, attach the frame you just built (36" x 11") to the 4x4 frame posts. You will use the pocket holes you drilled in the 36" boards. The frame will sit on the edge of the grooves, not inside. See plans for details. The frame should sit flush with the tops of your 4x4's. This will make the bottom 4" off the ground.


Wood tends to rise its general quality and character with the time passage. I would like to say that water wind rain snow possibly transform its porosity and texture and make it more attractive for a table piece. The attractiveness of this coffee table is the reason behind its mostly utilization. So, you can keep in mind this table as an excellent table.

We cut the decorative diagonal pieces to fit on this part. Mark each board with your pencil and cut them to fit exact. You can check out the video if you have questions about this part! We walk you through it. Cut the diagonal pieces to fit first, then mark and attach them to each other using wood glue and nails. Then, fit them in the box and attach them with wood glue and nails through the box and into each end of the X piece.


After they get empty, we remain no longer concerned with those wooden barrels! If you are having some long-forgotten wooden barrels they time to plan them for restoring living room fashion points! Here is way to convert an old barrel into a stunning coffee table that will also provide a secrete stash as you can see here! Perfect gift for rustic-modern lovers! Here is how to make it artofmanliness
The joiner is one of the oldest professions in the world, for centuries the wood masters have turned this fantastic material in artefacts that amazed people, functional furniture and other amazing creations. There still are craftdevicessmen and makers who continue this activity, renewing it and processing it to obtain better results and artifacts, with the help of woodworking machines, including SCM Classical machines that are distinguished by their excellent quality, precision and absolute security, allowing even less experienced hobbyists to obtain excellent results with no danger.
So, just like the lumberyard map, email your entries to me at [email protected], and to help sort through, put “Vacation Spot” in the subject line. It could be a Shaker village with outstanding furniture, the Giant Sequoias of Northern California or a quirky out-of-the-way museum or shop. This will be put up for public consumption just like the above map – I want everyone to find their lumber and see great woodworking.
×