A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.


Convert your Delta Midi-Lathe to a full size Convert your Delta Midi-Lathe to a full size lathe by adding the Delta Midi Lathe Bed Extension. Featuring a modular design so you can connect multiple extensions this extension increases bed length by 25-1/2 in. so you can turn longer spindles. To reduce vibration add 34 lbs. of cast iron ...  More + Product Details Close
The first step to building the table is to create the bottom shelf assembly. We used 2×4 boards for this part and ripped the boards to 3” wide each with our table saw. You don’t have to rip your boards on this part, but it will change the overall dimensions, so be sure to make those changes. We made 3/4“ pocket holes around all sides of the plywood panel. We also added 1.5” pocket holes to the ends of each long board. Attach the long sides of the panel to both sides using wood glue and 1.25” pocket hole screws. The plywood for the bottom shelf will be flush with the top of the 2×4 boards.
Carpentry is one of the most flexible and versatile construction occupations. As a graduate of a carpentry school online, you may work on a wide variety of projects, both indoors and outdoors—from installing kitchen cabinets and drywall to helping construct large-scale projects from the ground up. That versatility is helping to drive job growth: the U.S. Department of Labor expects carpentry careers to grow 8% by 2026.*
A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.
All Alison courses are free to enrol, study and complete. To successfully complete this Diploma course and become an Alison Graduate, you need to achieve 80% or higher in each course assessment. Once you have completed this Diploma course, you have the option to acquire official Certification, which is a great way to share your achievement with the world. Your Alison Certification is:
About forty years ago I purchased a Shopsmith Mark V because I lacked space for a large shop, and also moved around the United States a lot. Later I purchased another Shopsmith Mark V Model 510 for the increase in table size and flexibility. I do wood working as a hobby, not to do many projects as fast as possible. I also have every tool and accessory that Shopsmith makes for the two primary tools. Their quality is excellent, and while I enjoy antique tools like the 1912 three phase electric Camel Back Drill Press I purchased for my son’s shop, the Shopsmith does every thing I have ever needed.
Framing is another part of carpentry. Framing takes skill and experience it’s not a part of carpentry that anyone can just jump into. The skills that are required in framing is plumbing up a wall, make sure studs are 16 on center or whatever the specs calls for. Developing a good eye for straightness in carpentry work. Last but not least making sure everything is level.
Commercial carpenters build and remodel commercial office buildings, hospitals, hotels, schools, and shopping malls. Some specialize in light-gauge and load-bearing steel framing for interior partitions, exterior framing, and curtain wall construction. Others specialize in concrete forming systems and finishing interior and exterior walls, partitions, and ceilings.
Suppose you you were in possession of, as I am, four Cherry logs ranging in size from 18″ to 24″ diameter by 12′ to 16′ in length and you need to instruct the sawmill how they are to be cut. Also suppose that you are a novice woodworker who intends to use the resulting lumber in undetermined woodworking projects. How would you instruct the mill to cut up the logs?
You might not see these tables very often but they were relied on by sheep farmers for many years. Anything that could make the job of shearing sheep easier was welcomed on the farm. You could even change up the plan a little bit by making the legs longer and adding steel (or wooden) wheels to make a merchants cart. That latter idea is something we are suggesting, its not a part of this plan. Joinery methods used primarily in the construction of this sturdy table include mortise and tenon and tongue and groove. View the Larger Image Slideshow to see the actual paper plan you are buying.

Lumber for your projects can come from many sources, but before you can use it to build anything, it must be dry. Lumber that is kiln dried will have a moisture content right out of the kiln of 7 or 8%. However, by the time the lumber is delivered to your local dealer and arrives at your shop, the moisture content may have changed dramatically. Storage conditions between the kiln and your shop are clearly out of your control, so it is always a good idea after purchasing lumber to acclimatize it in your shop for several weeks. To avoid using lumber that is still in the process of adjusting to its new environment it is best to use a moisture meter to verify the moisture content of the wood. Most dealers don't mind customers checking the moisture content at the yard as long as they are using a pinless meter. The meter in my lumber kit uses electromagnetic waves to calculate the moisture content of a given piece of wood. Its use couldn't be simpler or quicker – simply turn it on, enter the species, and place the meter on the wood to be measured. The result is displayed right on the screen instantly without the need for conversion tables and other calculations. Typically, I check a couple of areas on each board as I select them just to confirm they are all in the same moisture range. Back at the shop I once more check each piece of wood and note it in chalk on the board. Every few days I'll recheck the boards, and when the readings have stabilized, I can be reasonably certain there won't be any surprises when I start the milling process.

You might be able to enroll in a General Contractor's License Preparation Certificate, a Carpentry Diploma or a Career Diploma in Carpentry program, among other options. Programs might require a high school diploma or its equivalent and a placement test. The programs may prepare you for entry-level positions in industry, engineering and the construction trades. The following topics might be covered in a carpentry or contracting program:
This is the side table version of the stylish project we shared previously. In certain configurations, it could function as a coffee table. It’s a design suitable for small spaces. The wooden top has this hollow storage compartment which is great for keeping things like a book, a magazine, the remote control or the phone when relaxing on the sofa. The hairpin legs give the table a slender look.

Loveland lies in Larimer county, which is one of the 55 counties in Colorado. Overall, the Fort Collins-Loveland area has 128,650 total employed workers according to the US Bureau of Labor Statistics, with a 2% unemployment rate, $21/hr average worker wage, and a $43,210 average annual salary. Thus, about 6 out of every 1000 jobs in Loveland are held by carpenters, and 6/1000 are held by construction laborers.
The course begins with a quick overview of the history of carpentry, from primitive to modern times. It then teaches you about the most important building materials, fasteners, adhesives, and tools used by carpenters in the modern construction industry. You will then receive an essential outline of safety guidelines and procedures. The course then goes through the crucial steps carpenters must take during construction projects. Here, you will be introduced to the best methods for constructing floor systems, walls, and roof framing, as well as how to make and read plans and elevations. The final section of the course shows you how to close off a structure, including installing windows, exterior doors, and stairs.
Industrial carpenters work on civil engineering projects and in industrial settings, where they build scaffolding and create and set forms for pouring concrete. Some industrial carpenters build tunnel bracing or partitions in underground passageways and mines to control the circulation of air to worksites. Others build concrete forms for tunnels, bridges, dams, power plants, and sewers.

Congrats! You've finished your coffee-table. If you liked building it and are happy with the result you can find other similar designs at www.screwed-up.com. If you want to know what's going on with Screwed-Up you can join the facebook page (https://www.facebook.com/Screwed-Up-2092172627662047/), or maybe you want to follow me on pinterest (https://nl.pinterest.com/screwedupdiyfurniture/pins/). For finishing touches I recommend sanding the edges and corners smooth. Also treating the top with a (clear) wood finish to protect against spills is never a bad idea.


The field of carpentry offers many opportunities for employment and advancement for workers with solid educational backgrounds and training. As work and educational experiences enhance your skill sets, you may earn the chance to advance to more responsibility and a higher salary. For example, you could be promoted to a general construction supervisor position within a larger construction company.
I think it depends on the type of woodworker you would like to become. Are you more interested in traditional “electric free” carpentry or are you drawn to the ease and convenience of modern machinery? Also, I think you should take into consideration what kind and how much shop space you have available. I have worked with all the modern machines for years now, and are just presently finding personal satisfaction in traditional woodworking. In fact, last night I built my very first bookcase with just a few “powerless” hand tools. So in all, I would suggest some personal reflection…What type of woodworker do you want to become?…and from there garnish your shop appropriately.
Carpenters craft structures and products from wood, steel, fiberglass and other materials. There are different types of carpenters, including residential, industrial and commercial carpenters. Residential carpenters may build new homes or do remodeling work, building structures like walls, stairways, floors, roofs and decks. Commercial carpenters, who may construct schools, malls and hospitals, use many of the same skills, but they may work more with concrete and steel. Industrial carpenters build infrastructure like tunnels, sewers and dams. 

The most commonly purchased claw hammer is the 20 oz. size. It’s heavy enough to easily drive nails but easily manipulated when pulling nails. While wooden handles are picturesque, they may not stand up to the strain if you have to pull a lot of nails. Hammers with a steel handle, or even fiberglass, will be stronger. However, these won’t absorb the vibrations from driving nails the way a hickory handle will. You’ll also need to make sure the fiberglass and metal handles have a rubberized grip for control and comfort. If you’re going to be driving a lot of nails, the wooden handled hammer will be better for reducing stress on your hand, and wrist, too.

First, build two boxes for each leg assembly. These are attached using wood glue and 2.5” pocket hole screws through the horizontal boards and into the vertical boards.  You want your pocket holes facing the outside of the box on this part because we will cover them with another board on the next part.  We used our K5 Kreg Jig for this part.  We get asked ALL the time which Kreg Jig to start with.  We always suggest the K5.  We use it on almost every build.  You can find it HERE on Amazon!
Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!
×