1. Power jointer and thickness planer. I have developed various means of straightening the edges of my stock with hand-held tools, but I don’t see a way to efficiently flatten the faces of rough or reclaimed lumber without a power jointer. It’s part of the first few steps for any furniture project, and I want to be able to move through this step quickly and into the more interesting work. The thickness planer is also a huge time-saver, compared to hand-held tools.
However, if you want to stain or clear-coat the project, you'll have a number of choices to look through. Since your local home center megamart will probably only carry a couple of hardwood species (poplar and red oak are common) spend time at a fine wood supplier and look through the vareties available. They should be able to help you determine how each species will look when finished, which will go a long way toward refining your decision.
Using wood glue and 1 1/4" pocket hole screws, attach the frame you just built (19" x 11") to the 4x4 frame posts. You will use the pocket holes you drilled in the 19" boards. The frame will sit on the edge of the grooves, not inside. See plans for details. The frame should sit flush with the tops of your 4x4's. This will make the bottom 4" off the ground. 

Now, I know this list only contains traditional hand tools, but my circumstances led me to this choice to complete the job. After all, he is my brother and he’s helped me once or twice. Not all woodworkers will want to take the time and effort to go strictly with hand tools. That’s fine; different circumstances and preferences will lead the way. Most people wouldn’t drive a scooter full of tools to assist their siblings either. Sounds crazy, but I enjoyed the trip through the mountains. Once I was there, I still needed a way to rip through lumber. I also needed a can of finish. As needed, a few jigs and templates were constructed from the purchased lumber.
For furniture making, the best, most stable stock has the annual growth rings intersecting each face at approximately the same angle, roughly 45º. Wood cut this way is referred to as quarter sawn. Milling quarter sawn lumber is a labour intensive process, which is why it costs more than plain-sawn lumber. The appearance of the grain will tend to be similar on all four sides. This makes quarter sawn lumber a great choice for table legs, rails and stiles of frame and panel doors, or for any part where two adjacent sides are visible.
Carpentry skills can be applied to residential or commercial remodeling, cabinet making and exterior and interior trim. Coursework in carpentry classes commonly includes instruction in building safety, construction codes, framing and site layout. These courses are widely available at technical schools and colleges. Hands-on practice is emphasized in most classes.
There are often situations when the original message asks for opinions: "What is the best widget for my type of shop?". To a certain extent, the person posting the message is responsible for including specific questions within the message. An open ended question (like the one above) invites responses that may read as sales pitches. WOODWEB suggests that companies responding to such a question provide detailed and substantive replies rather than responses that read as a one-sided product promotion. It has been WOODWEB's experience that substantive responses are held in higher regard by our readers (return to top).
Carpenters craft structures and products from wood, steel, fiberglass and other materials. There are different types of carpenters, including residential, industrial and commercial carpenters. Residential carpenters may build new homes or do remodeling work, building structures like walls, stairways, floors, roofs and decks. Commercial carpenters, who may construct schools, malls and hospitals, use many of the same skills, but they may work more with concrete and steel. Industrial carpenters build infrastructure like tunnels, sewers and dams.
Afrormosia Alder Andiroba Anigre Ash Apple Aspen Avodire Balsa Beech Bilinga Birch African Blackwood Australian Blackwood Boxwood Bubinga Camphor Cedrela Cherry Chestnut Cocobolo Cumaru Ebony Elm Eucalyptus Hazel Hickory Hornbeam Idigbo Imbuia Ipê Iroko Jarra Jelutong Lignum vitae Linden (lime, basswood) Merbau Mahogany (American, African) Maple Meranti Oak Padauk Pear Plum Poplar Purpleheart Ovankol Ramin Red Quebracho Rosewood Rubberwood Sapele Teak Totara Utile Walnut Wenge Willow Zebrano

A robust media plan further supports Northwest Hardwood’s industry leadership position and further enhances the company’s presence in trade and design media and online spaces. In addition to the traditional customer base, Northwest Hardwoods will also reach architects and designers via a mix of print and digital advertising in publications such as Dwell, Architect Magazine, and Elle Décor. TWIST created a new tagline Keep Pioneering which plays off of the company’s Northwest roots.

Wow, what a great problem to have Boris! If you can send some photos I’ll look at them. But unseen, I’d ask them to try to get some quartersawn boards out, and also some full width flatsawn boards. It just depends on how much wood you’ll get if you quartersaw it. It also depends on what you think you’ll build down the road. Some furniture pieces don’t need to be quite as stable as others. Good luck!

In the end, do not forget the decorating aspect. As any table in your home, your perfect coffee table deserves the right centerpiece that will embellish and accentuate its beauty.Choose from a wide variety of designs. We also recommend you to try a diy centerpiece project to complete the design such a beautiful DIY wine bottle centerpiece. Find a lovely collection of such projects below and learn how to cut glass in a very easy step by step tutorial.


Loveland, CO (population: 68,614) has four carpentry schools within a 100-mile radius of its city center. Emily Griffith Opportunity School, the highest ranked school in this group with a carpentry program, has a total student population of 2,230. It is the 2063rd highest ranked school in the USA and the 22nd highest in the state of Colorado (#1 is Colorado College).
Teak is becoming rarer as the days go on, but it is the staple for fine outdoor furniture. Teak is highly weather-resistant and beautiful (not to mention expensive — can you believe almost $24 a board foot?). Teak has an oily feel and a golden-brown color. It rates a 3 on a scale of 1 to 5 for hardness and is only available from larger lumberyards and specialty suppliers.
You might be able to enroll in a General Contractor's License Preparation Certificate, a Carpentry Diploma or a Career Diploma in Carpentry program, among other options. Programs might require a high school diploma or its equivalent and a placement test. The programs may prepare you for entry-level positions in industry, engineering and the construction trades. The following topics might be covered in a carpentry or contracting program:
I’ve gained a lot more confidence in my woodworking capabilities over the last year, so I wanted to tackle this project solo (a.k.a. without the assistance or supervision of Jeremy), and I was actually really surprised at how easy and fast this table came together. I was able to shop for my supplies, make my cuts, and build the table all within just a few hours. Not bad for a little afternoon project!
A carpenter is someone who builds and repairs residential, commercial, or industrial structures. These structures can range from homes to commercial buildings to roads and can include individual components such as cabinets, staircases, doorframes, building foundations, and much more. And, although you may think that this occupation only requires physical strength and basic technical skills, carpentry actually requires a strong foundation of specialized expertise and experience in order to ensure that all jobs are completed in accordance with local, state, and national building codes.
Students learn the basics of residential house framing, including layout techniques, roof and wall framing, planning for windows and doors and the pouring of a foundation. Following classroom instruction in basic carpentry math and materials estimation, students have the opportunity to employ their carpentry skills by working together on a residential building project. Teamwork, workplace ethics, craftsmanship and punctuality are emphasized in the practical portion of the course.
Once the vinegar solution dries (or if you decided not to do the solution) you can go ahead and stain the project. First use a rag or air compressor to remove any dust from the table. Then use a clean rag to apply the stain of your choice. Don't forget to wear gloves and ventilate the area. Have a brush in your other hand to stain hard to reach areas.
This is the side table version of the stylish project we shared previously. In certain configurations, it could function as a coffee table. It’s a design suitable for small spaces. The wooden top has this hollow storage compartment which is great for keeping things like a book, a magazine, the remote control or the phone when relaxing on the sofa. The hairpin legs give the table a slender look.
Your moisture meter should have settings on it that will account for different species of wood. For instance, oak is a hardwood, but ebony is an even harder density wood. If you are planning an inlay job using both types of wood, you will need to know the moisture content levels of each of the two species so that your inlay glue joints will stay intact. These different wood species have different specific gravities, which must be used or programmed into the moisture meter.
Furniture Making engages students in the process of furniture making. Topics include an American historical overview and a look at the use of power and hand tools. Common themes include sketchbook work, cutting, hand tools, power tools, bending and jig making. This course employs various technical readings, visual aids, videos, project pictures and assignments. 

Industrial carpenters work on civil engineering projects and in industrial settings, where they build scaffolding and create and set forms for pouring concrete. Some industrial carpenters build tunnel bracing or partitions in underground passageways and mines to control the circulation of air to worksites. Others build concrete forms for tunnels, bridges, dams, power plants, and sewers.
Typically, a carpentry training program will cover the following subjects: algebra; geometry; physics; hand tool selection, care, and use; architectural drawing; blueprint reading; machine woodworking; identification and measurement of materials; project management and estimating; principles and procedures in residential construction; building code requirements; framing and finishing; building technology; roofing systems; interior and exterior finishing; door and window layout and construction; and mechanical systems.

While flipping through the boards, keep an eye open for signs that a number of boards may have come from the same tree. Looking at the ends and the growth rings will tell you where in the log the board was sawn. In some cases, knots may go through more than one board, and often the outer boards have a live edge. By comparing these features, the colouring, grain and other distinguishing marks, it is often possible to identify several boards cut from the same log.
Ashworth College is unlike any other carpentry school online. Our Carpentry training focuses on the real-world tools, knowledge, and procedures used by construction professionals on residential and commercial building projects. Studying online in a way that fits your busy life, you’ll graduate with the carpentry skills employers demand, helping you focus on practical skills and turn your woodworking hobby into a true profession.
Dan, my work space that is available for power tools is quite small, about 6′ x 20′. It may seem like a lot on the surface, but a long rectangle is a bear to work in. It requires a lot of serpentine action. That said, I don’t have too much room for large footprint tools. I have settled finally on three big tools; a small bench saw, a thickness planer, and a drill press. I had to forgo the jointer, so I use hand tools to make up for it’s absence (as I do with a lot of my hand tool techniques). I have gotten to the point where I can flatten one side and true an edge of a board reasonably quick. I then finish it up with the thickness planer and table saw, giving me a nice flat board. I guess what I am basically saying is, there’s more than one way to skin a cat, and don’t write off hand tools as a quaint way to experience the past. They worked for thousands of years, and still do! Thanks for the blogs, they make for great reading.
So, just like the lumberyard map, email your entries to me at [email protected], and to help sort through, put “Vacation Spot” in the subject line. It could be a Shaker village with outstanding furniture, the Giant Sequoias of Northern California or a quirky out-of-the-way museum or shop. This will be put up for public consumption just like the above map – I want everyone to find their lumber and see great woodworking.
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.
Teak is becoming rarer as the days go on, but it is the staple for fine outdoor furniture. Teak is highly weather-resistant and beautiful (not to mention expensive — can you believe almost $24 a board foot?). Teak has an oily feel and a golden-brown color. It rates a 3 on a scale of 1 to 5 for hardness and is only available from larger lumberyards and specialty suppliers.
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.
Rough lumber is sold and measured in ¼" increments; when a board is referred to as 4/4, it means it is four quarters of an inch thick, or one inch. The most common sizes you are likely to encounter at the lumber yard are 4/4 (1"), 6/4 (1½"), 8/4 (2") and 12/4 (3"). Generally, larger dimension lumber is priced per board foot. Price is also dependant upon the wood quality. Boards without blemishes, and of even colour, command higher prices. On most projects it isn't necessary to purchase the best grade material for the entire project. Purchasing a lower grade will allow you to bring home more lumber, and give you the freedom to lay out parts based on appearance rather than waste.
I want to make some wooden boxes and cases, and I haven't done any wood work till now so I don't have any tools and I can't buy the workshop electronic machines which I see in almost every woodworking instructables here (such as drill, lathe, sanding, saw, mitre, buiskit jointer, and all other electronic tools). So I want to begin with simple hand tools.
The next hand tool every woodworker should have is a nail set. In fact, you should have several sizes. They look like awls, and you use them to drive nail heads into the wood so they are flush or right below the surface. This allows you to fill the holes and prepare for staining or painting. The nail setter will usually have either a convex or concave surface to grip the nail better and keep it from sliding off and marring the wood.

Building a coffee table with hairpin legs is fairly easy, especially if you choose a simple design for the top. There are several options to choose from in that case. One is to build a simple frame which looks something like this. That way the coffee table would look pretty, would be easy to build and would also include a storage compartment which is always useful.
This is also a table made from a repurposed pallet. There’s not much you need to change about the pallet, except rearrange a few boards and make the frame smaller. The fact that each board has a slightly different color tone gives the table a special charm. The hairpin legs are a really nice touch. Check out the full tutorial to find out more about how you can build something similar for your own home.
I love this & your videos. It’s really helped my confidence level (as a total beginner.) I’ve built your floating shelves (LOVE them) and the cake stand you did (I’m adding dowels in the middle for the connecting parts so I can take it apart & store it almost flat & not worry about Velcro) I’m wondering if you’d do a console that matches this? I really like Ana White’s x console but liked your legs better!
The owners, webmasters, administrators, authors and editors, expressly disclaim all and any liability to any person, whether a user of this website or not, in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance, whether whole or partial, upon the whole or any part of the contents of this website. Please exercise caution when working with any tools or machinery. Follow common safety rules and precautions as outlined in any manuals related to the equipment being used. If advice or other expert assistance is required, the services of a competent professional person should be sought.

The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.


Not all species are available in quarter sawn form from all dealers, but it can be possible to cut parts from wider boards to accomplish the same end. At the lumberyard I will often look for wider planks for this very reason. When a wide board is cut from the log it will have some vertical grain on the outer edges and some face grain in the center of the board. By purchasing enough stock and carefully laying out the parts it would be possible to use quarter sawn material for all visible parts. Decisions like this must often be made at the lumberyard based on the stock on hand. It is a way to stretch your material budget a little further, by buying a lower grade and resawing it for appearance back in the shop.

Products and systems by Lamello have always been Products and systems by Lamello have always been designed for longevity and reliability. This legendary durability is combined with environmental stewardship in view as strict environmental regulations at our production site in Switzerland ensure that all resources are used with consideration many of them stemming from sustainable husbandry and management. ...  More + Product Details Close

“Basic,” on the other hand, is a word that allows for growth – and that’s exactly what you want in your woodworking tool kit. You want to be able to take the same kit with you through many years in the craft. With my basic woodworking tools list, I wanted to provide a core set of tools that will serve you well from project to project. I’m especially concerned these days with the transition to hardwood furniture making, as opposed to plywood boxes of various sizes. That’s the transition I’m making right now in my own work!
This course introduces students to remodeling practices and demolitions. Students learn how to plan a remodeling project, complete basic plumbing and electrical jobs, apply for permits, match finished materials and estimate costs. Instruction in reading architectural blueprints for residential remodels is generally included, and students become familiar with specifications, codes and construction drawings. Some residential remodeling courses provide hands-on learning experience by requiring group or individual remodeling projects. This course is usually taken after basic carpentry courses.
The sequence in which boards are cut from a log will determine how stable the boards will be once they dry. As a board loses moisture it will shrink in three dimensions. The change in length is so small as to be considered insignificant and the change in radial movement is always less than the tangential movement. This is most significant as the wood dries between the time it's cut (i.e. green wood), and the point where it is kiln dried or air dried and ready for use. Wood that shrinks excessively, or that has been dried improperly, will often develop checks at the ends. When shopping for lumber, carefully inspect the ends for any checking, or for excessively long checks. It is best to allow for some scrap at the end of each board, just in case. As you trim the end, hit the off-cut across the edge of your bench, and if it breaks in two, you'll have to cut off a little more.

I’ve been wanting an excuse to buy a Kreg Jig for probably a year now, and with a long DIY to-do list of building tables, benches, and more for our living and dining room, I decided now was a good time to make the purchase. This project is in no way sponsored by Kreg Jig, but I was so impressed with how much easier this tool made my life, I just had to share it with you guys! This tutorial (and probably most builds from here on out) will be shown using the Kreg Jig, so if you enjoy building things for your home, I highly recommend getting yourself one! You can purchase the kit I have here: Kreg Jig K4 Pocket Hole System.


The owners, webmasters, administrators, authors and editors, expressly disclaim all and any liability to any person, whether a user of this website or not, in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance, whether whole or partial, upon the whole or any part of the contents of this website. Please exercise caution when working with any tools or machinery. Follow common safety rules and precautions as outlined in any manuals related to the equipment being used. If advice or other expert assistance is required, the services of a competent professional person should be sought.

When I started planning this makeover, I knew I wanted to get rid of the glass coffee table I had and go with something more rustic and cozy… something with beautiful wood grain that looks like it’s been in an old farmhouse somewhere for ages. So rather than searching every single antique store in town or buying something off the shelf at a big box store, I gathered up my tools, picked up some lumber, and made myself a new coffee table!
We are all well aware of the role of a DIY coffee table for a living room which is highly versatile! It is what you need to get first while entertaining some visitors or guests in the living room! The conversations are also to start always by sitting around it! It is seen mostly in the center of the sitting plans! The reason is that all the sitting personages can use it to place their mobile phones, cups, beverage mugs, magazines and other materials over it while they need to get their hands free for the detailed conversations! So this all tells that how utilitarian item a coffee is!
One of the simplest things you can do is transform a simple wooden pallet into a coffee table. It would be an easy conversion and the result could be similar to this pallet coffee table. Using the boards of the pallet you basically put together the top and the corner and side pieces along with a central support piece. That’s pretty much the whole table and all that’s left to do is add the wheels. So there you have it: your very own pallet coffee table on wheels.
If you have already completed some college or university education, then many apprenticeship programs will give you credit for prior learning. You can even receive credit for work experience you possess in the construction field. It is important to note that any education and work experience credits will likely be evaluated on a case-by-case basis, so if you want to explore this option, then checking around for the best use of your experience is key.
Description: Every woodturner enjoys the opportunity to give handmade ornaments to friends and family during the holidays, especially one that is made purely out of wood. No pre-made ornament kits or ornament hardware will be used in this class. One might call it au naturel!!!! During this class you will be given the opportunity to see various ornaments that have been turned on the lathe, ranging from small and simple to large and more decorative. Class objectives include, but are not limited to, the following: Wood choice (more common ornament wood species and pros and cons of each) Discussion and demonstration on how ornaments can be colored using a variety of markers, paints, dyes, and gilder's paste. Discuss and demonstrate how a variety of gouges and tools can be used to make ornaments, including texturing tools. Sharpening techniques - the instructor will assist all students when sharpening tools Ornament rough sketch and design, before the wood is on the lathe. Most important, every student in class will be given the opportunity to turn at least one ornament of their own. The instructor will assist with basic sketch and design, and will rotate among all students to assist with cuts, tool use, technique, sharpening, and helpful hints. Experience level: Beginner (some turning experience highly preferred) Suggested tools: Turning tools will be supplied; however, students are encourage to bring their own tools if they have them. 3/8" or 1/2" spindle gouge, narrow parting tool, and small roughing gouge is a great start. Students who wish to bring their own chuck may do so as well (1"-8 tpi, 2" or 50mm dovetail jaws, and pin jaws). Lunch break from 12:00 to 12:45
I’m currently working on a dining room table with this color in mind (I also plan on a coffee table soon). I’ve been testing out stain colors and dark walnut is currently in the lead. I love the way this coffee table turned out in color. How many coats of stain did you use? Also, did the dark wax make a big difference in color? I was planning on using a satin poly for sealant (mostly because it’s what is most convenient and what I’m accustomed to), but I’m interested in the dark wax after seeing this post. Any recommendations you have are much appreciated.
×