This project actually started with me wanting to build a chair for myself, however I lacked advanced woodworking tools and a workshop. I therefore began making furniture that was as straightforward as possible and could be build easily with simple tools. Most importantly, all parts could be cut at the DIY store where I got my plywood. This meant I didn't need a saw bench or lots of space. The cut parts were easy to transport to my home and I could pretty much build the whole chair on the kitchen table. This inspired me to make other furniture pieces in similar fashion.
Description: Every woodturner enjoys the opportunity to give handmade ornaments to friends and family during the holidays, especially one that is made purely out of wood. No pre-made ornament kits or ornament hardware will be used in this class. One might call it au naturel!!!! During this class you will be given the opportunity to see various ornaments that have been turned on the lathe, ranging from small and simple to large and more decorative. Class objectives include, but are not limited to, the following: Wood choice (more common ornament wood species and pros and cons of each) Discussion and demonstration on how ornaments can be colored using a variety of markers, paints, dyes, and gilder's paste. Discuss and demonstrate how a variety of gouges and tools can be used to make ornaments, including texturing tools. Sharpening techniques - the instructor will assist all students when sharpening tools Ornament rough sketch and design, before the wood is on the lathe. Most important, every student in class will be given the opportunity to turn at least one ornament of their own. The instructor will assist with basic sketch and design, and will rotate among all students to assist with cuts, tool use, technique, sharpening, and helpful hints. Experience level: Beginner (some turning experience highly preferred) Suggested tools: Turning tools will be supplied; however, students are encourage to bring their own tools if they have them. 3/8" or 1/2" spindle gouge, narrow parting tool, and small roughing gouge is a great start. Students who wish to bring their own chuck may do so as well (1"-8 tpi, 2" or 50mm dovetail jaws, and pin jaws). Lunch break from 12:00 to 12:45
Lots of good comments! I do think it is a bit of stretch to include a jointer and surface planner on the ‘basics’ list – we’ve got a slippery slope here! And a lot of different approaches – money, space, time, resources, etc. But lets plunge ahead. If you buy your wood already (or mostly) prep’ed, then the jointer & surface planner can be postponed. You definitely need a way to accurately measure linear distances (e.g. length, width) so a good ruler and tape measure. You need to be able to measure squareness – so you need a good combination square. You need to be able to mark the wood – so a good marking knife, an awl, some chalk, a fine pencil, etc. You should have some decent chisels (and good ones don’t need to cost a lot!). You will need to sharpen them (again not expensive – piece of plate glass and some sandpaper). You need a way to accurately cut your wood – a couple of good handsaws and a file or two for sharpening. You really should have a decent work surface/work bench/etc – a good first project by the way. Last of the basics – a good drill (3/8″ vs battery type). Lastly (I could go on but room is lacking), take a look at Paul Seller’s video’s for simple but highly competent work.

Home Site Map What's New New Visitors Video Library Software & Mobile Apps Auctions, Sales and Special Offers Industry News Woodworkers Directory Sawing and Drying Directory The Wood Doctor Bookstore Lumber Buying Guide Tradeshow Directory Newsstand Lumber/Timber/Misc Calculators Events Calendar Media Kit Poll Center About WOODWEB What Our Visitors Say Frequently Asked Questions Contact WOODWEB User Agreement and Terms of Use Privacy Policy Link to WOODWEB Refer a Friend Subscribe to the WOODWEB Update Update Archive Become a Member
Sears Trostel is the source for the highest quality lumber, custom millwork, specialty wood products, FSC® certified products and tool brands. Serving commercial and retail customers throughout Colorado and Rocky Mountain communities since 1929, our 10,000-piece moulding and interior trim library, super-fast Lean Manufacturing processes, and huge inventory of products and services are unmatched in the region. 
There are often situations when the original message asks for opinions: "What is the best widget for my type of shop?". To a certain extent, the person posting the message is responsible for including specific questions within the message. An open ended question (like the one above) invites responses that may read as sales pitches. WOODWEB suggests that companies responding to such a question provide detailed and substantive replies rather than responses that read as a one-sided product promotion. It has been WOODWEB's experience that substantive responses are held in higher regard by our readers (return to top).
One of the simplest things you can do is transform a simple wooden pallet into a coffee table. It would be an easy conversion and the result could be similar to this pallet coffee table. Using the boards of the pallet you basically put together the top and the corner and side pieces along with a central support piece. That’s pretty much the whole table and all that’s left to do is add the wheels. So there you have it: your very own pallet coffee table on wheels.

Integrating a planter into a table is actually a pretty common idea. We’ve seen quite a few projects which include this feature and one of them comes from abeautifulmess. Check out the plans to find out how to put together with a minimalist and stylish coffee table with a planter at its center. You can use that space as a herb garden or you can plant grass or succulents in there. We really the crisp and linear design, the pureness of the white body and the strong contrast with the black legs and the green of the plants. It’s refreshing in a very special way.
Rip your 1x4's so they are 3" wide. This should make them nice and square, so they fit together without any gaps or rounded edges. Drill pocket holes in both ends of each board. Drill several pocket holes (3 or 4) on the edges of each board. Spread wood glue on the edges of each board, and sandwich them together, using bar clamps to keep them tight. Using 1 1/4" pocket hole screws, attach the 1x4's together. (see photo on next step)
Cut 2- 1x6 46" boards, mitered at 45 degrees on each end (measurement is taken on long side). Cut 2- 1x6 17" boards, mitered at 45 degrees on each end (measurement is taken on long side). Drill pocket holes in both ends of each board. Drill several pocket holes (3 or 4) on the INSIDE edges of each board. Spread wood glue on the edges of each board, and sandwich them together, using bar clamps to keep them tight. Using 1 1/4" pocket hole screws, attach the 1x4's together. (see photo on previous step)
I have used a Workmate successfully for years and I am in the process of building an upgraded replacement for the work surfaces. My replacement bench top will be a little longer, much thicker and it will have and extended apron between the two halves to greatly improve holding wood vertically for dovetailing. With this simple upgrade it turns the little Workmate into a very capable portable woodworking bench.
I love this & your videos. It’s really helped my confidence level (as a total beginner.) I’ve built your floating shelves (LOVE them) and the cake stand you did (I’m adding dowels in the middle for the connecting parts so I can take it apart & store it almost flat & not worry about Velcro) I’m wondering if you’d do a console that matches this? I really like Ana White’s x console but liked your legs better!
Loveland, CO (population: 68,614) has four carpentry schools within a 100-mile radius of its city center. Emily Griffith Opportunity School, the highest ranked school in this group with a carpentry program, has a total student population of 2,230. It is the 2063rd highest ranked school in the USA and the 22nd highest in the state of Colorado (#1 is Colorado College).
While this coffee table instruction is free, I'm trying to make a living with these. I care about the quality of each piece and a lot of work went into designing the pieces and making the instructions so unfortunately I have to ask a little money for the other instructions. However when put into the perspective of a whole DIY furniture project I guess it shouldn't make that big of dent in your budget.
Having completed this course the learner will be able to: - Describe the history and scope of carpentry as a trade; - Identify the opportunities for carpenters in the construction industry; - Classify the various building materials used by carpenters; - List the most commonly used fasteners and adhesives used by people in the carpentry trade; - Explain the different types of hand and power tools available to carpenters; - Outline the general safety procedures and guidelines that should be followed to operate the tools; - Discuss the importance of employee responsibility and human relations to being successful in the trade; - Identify the various types of construction drawings that make a drawing set; - State the guidelines to read and interpret reading plans and drawings, blueprints, and specifications; - List the various terms associated with floor systems, wall, ceiling and roof framing; - Explain the different methods of framing and constructing houses made of wood; - Describe the types of beams/girders and supports used in construction; - Outline the sequence involved in constructing a platform floor assembly; - Summarize the basic procedure for laying out, assembling, and erecting wood frame walls; - Recognize the different types of roofs used in residential construction; - Determine the length of a common rafter required to construct a roof; - Discuss the terms associated with concrete, concrete reinforcing materials, and formwork; - Apply the concrete mixing information to get different types of concrete, designed to suit various purposes; - Explain the basic concrete curing methods and materials; - List the various components of windows, exterior doors, and stairways used in residential construction; - Summarize the basic installation procedure for pre-hung windows; - State the various types of exterior doors used in residential construction; - Identify the essential requirements for framing stairs; - Describe the design and layout techniques used for stairways and stairwells.
There are three very important elements that must come together in making a project that will not only be pleasing to the eye, but will stand the test of time: good design, careful workmanship and meticulous selection of materials. You can continue to refine your design on paper, but at some point you will have to make that transition from a two dimensional drawing to selecting the lumber to use for each part. This can be one of the most difficult phases of any project and one that has the greatest effect on the final appearance of your finished piece.
Even though this is in fact a side table, we can definitely find inspiration in its design. We find this project to be highly creative and interesting. The table has a hexagon-shaped top and bottom connected by two sets of five rods. Two in each set are longer than the other and go through the bottom hexagon, acting as legs. You can find the plans for this project on ohohblog. 

In this step take your 2×2 rails that are 41″ long and drill  2 pocket holes on each end using a Kreg Jig. Then take 2 1/2 kreg screws and attach the side rails to each 2×4 end piece. Measure 2 1/4 inches up from the bottom to hang your lower 2×2 rail. Note that in the photo my pocket hole screws are pointing inward. The top rail's pocket holes can face inside the table or to the ground. No matter what they won't be seen. Make sure to have the lower rail's pocket holes facing the floor so you'll be able to attach the shelf to them later.
Carpenters learn many physically-oriented skills, like joining, framing and refinishing. Carpenters also must be adept at measuring and planning to complete the layout portion of their tasks. Errors in this important pre-step to the building process can negatively impact, or even ruin, a finished product. Additionally, mathematical skills and blueprint reading and sketching are vital skills for carpenters.
Scm specializes in designing and manufacturing woodworking machines and services for joineries and customized production shops working with melamine panels, solid wood and other plastic materials. All machines are configured to offer the best technological innovations, high performance and reliability. Easy to install and easy to use, Scm products are distributed all over the world. 
Description: In this four day class, we will start with rough lumber and finish with a simple box. Along the way we will teach you how to use the jointer, planer, table saw, and router table This is THE class to take if you are interested in getting started the right way in woodworking. This one will fill up fast, so sign up. soon. Woodworking 101 is strongly recommended for beginners and people looking to review the basics.

It's a little awkward, so we'll get straight to the point: This Wednesday we humbly ask you to defend Wikipedia's independence. We depend on donations averaging about $16.36, but 99% of our readers don't give. If everyone reading this gave $3, we could keep Wikipedia thriving for years to come. The price of your Wednesday coffee is all we need. When we made Wikipedia a non-profit, people warned us we'd regret it. But if Wikipedia became commercial, it would be a great loss to the world. Wikipedia is a place to learn, not a place for advertising. It unites all of us who love knowledge: contributors, readers and the donors who keep us thriving. The heart and soul of Wikipedia is a community of people working to bring you unlimited access to reliable, neutral information. Please take a minute to help us keep Wikipedia growing. Thank you.
While flipping through the boards, keep an eye open for signs that a number of boards may have come from the same tree. Looking at the ends and the growth rings will tell you where in the log the board was sawn. In some cases, knots may go through more than one board, and often the outer boards have a live edge. By comparing these features, the colouring, grain and other distinguishing marks, it is often possible to identify several boards cut from the same log. 

Upcycling and recycling are our mottoes thus it is just natural for old door tables’ transformations to be a segment of a collection of our free point, particularly when this kind of crafts and projects have a reused material and sustainable side enriched by the passage of period. Old wooden door recycled into the table is a very good technique for beginners.
For furniture making, the best, most stable stock has the annual growth rings intersecting each face at approximately the same angle, roughly 45º. Wood cut this way is referred to as quarter sawn. Milling quarter sawn lumber is a labour intensive process, which is why it costs more than plain-sawn lumber. The appearance of the grain will tend to be similar on all four sides. This makes quarter sawn lumber a great choice for table legs, rails and stiles of frame and panel doors, or for any part where two adjacent sides are visible.
An associate's degree program can be very valuable if your ultimate goals extend to working in management since many leadership roles require a degree credential in a related field. However, if you are more interested in the hands-on aspect of the profession, then a diploma or certificate program can provide the technical knowledge needed to meet the demands of the job.
You will perfect your marking, cutting and chiseling skills by making a series of common woodwork joints each joint being that little bit more difficult than the last. These skills will come in for later during the course when you will be required to chop in hinges using a chisel into a door and door frame plus build a door frame with a half lap joint.
Dan, my work space that is available for power tools is quite small, about 6′ x 20′. It may seem like a lot on the surface, but a long rectangle is a bear to work in. It requires a lot of serpentine action. That said, I don’t have too much room for large footprint tools. I have settled finally on three big tools; a small bench saw, a thickness planer, and a drill press. I had to forgo the jointer, so I use hand tools to make up for it’s absence (as I do with a lot of my hand tool techniques). I have gotten to the point where I can flatten one side and true an edge of a board reasonably quick. I then finish it up with the thickness planer and table saw, giving me a nice flat board. I guess what I am basically saying is, there’s more than one way to skin a cat, and don’t write off hand tools as a quaint way to experience the past. They worked for thousands of years, and still do! Thanks for the blogs, they make for great reading.
A layout square, or combination square, comes in 6” and 12” sizes. Most woodworkers use the 6” model, simply because it’s easiest to carry around. Also, most of the stock you’ll use will be no bigger than 6” wide, so 12” is overkill. The layout square is a triangle that you can use to mark square cuts on stock. Once you measure the length of the cut, you line up the layout square with the edge of the board. The short side will give you a straight, square cut across the end grain. You can also measure off angles with the layout square. This helps when you’re trying to measure for a bevel on a table saw, or marking a cut for a miter saw. You can even use your layout square to determine an existing angle. Just be sure to buy one made of metal. The plastic ones are not only fragile, but they also can warp, making them pretty useless.
“The earliest credible evidence of coffee-drinking appears in the middle of the 15th century in the Sufi shrines of Yemen. It was here in Arabia that coffee seeds were first roasted and brewed, in a similar way to how it is now prepared. Coffee seeds were first exported from Eastern Africa to Yemen, as the coffee plant is thought to have been indigenous to the former.Yemeni traders took coffee back to their homeland and began to cultivate the seed. By the 16th century, it had reached the rest of the Middle East, Persia, Turkey, and northern Africa. From there, it spread to Europe and the rest of the world.” [source]
Let’s start with perhaps the most basic tool in every household – the claw hammer. The claw on one side of the head should be well counterbalanced by the finished head, which should be somewhat rounded. The other kind of head is the waffle-head. Most commonly used in construction, it leaves a distinctive waffle mark on the wood when you drive the nail. This, of course, is not the proper nail for woodworking.
Thank you so much, Fawn!! I think using pocket holes to connect the top boards is a fantastic idea, and we actually did that with the bigger dining room table we did a few weeks ago. For our coffee table, I kind of liked the look of small gaps in between each board… gives it a more rustic look I think! 🙂 Have fun building your table… I’d love to see it! Tag me on Instagram!
Now that you know how to become a carpenter, you might wonder what the job's like on a day-to-day basis. Because carpentry work demands vigorous exertion, carpenters must be physically fit, strong, and have a good sense of balance. Carpenters must able to work long hours standing, climbing, bending, and kneeling. Additionally, carpenters must be detail-oriented, with good hand-eye coordination and strong problem-solving skills. As carpentry work can be stressful, they must also be able to manage tension and handle workplace pressures. Carpentry work often involves physical risks, like falling and slipping injuries or bruises and cuts from working with sharp tools and rough, heavy materials. Weather conditions and exposure can also pose dangers for carpenters working outdoors.

I’m currently working on a dining room table with this color in mind (I also plan on a coffee table soon). I’ve been testing out stain colors and dark walnut is currently in the lead. I love the way this coffee table turned out in color. How many coats of stain did you use? Also, did the dark wax make a big difference in color? I was planning on using a satin poly for sealant (mostly because it’s what is most convenient and what I’m accustomed to), but I’m interested in the dark wax after seeing this post. Any recommendations you have are much appreciated.
Dan, my work space that is available for power tools is quite small, about 6′ x 20′. It may seem like a lot on the surface, but a long rectangle is a bear to work in. It requires a lot of serpentine action. That said, I don’t have too much room for large footprint tools. I have settled finally on three big tools; a small bench saw, a thickness planer, and a drill press. I had to forgo the jointer, so I use hand tools to make up for it’s absence (as I do with a lot of my hand tool techniques). I have gotten to the point where I can flatten one side and true an edge of a board reasonably quick. I then finish it up with the thickness planer and table saw, giving me a nice flat board. I guess what I am basically saying is, there’s more than one way to skin a cat, and don’t write off hand tools as a quaint way to experience the past. They worked for thousands of years, and still do! Thanks for the blogs, they make for great reading.

If desired, add decorative trim pieces to your coffee table. We used an x pattern, but you can leave it as-is if desired. Simply dry fit your pattern into the side panels of your coffee table. Then attach using wood glue and brad nails. After your pieces have been added, fill any holes. Once your wood filler is dry, sand with 120 grit sandpaper. Then stain or paint and finish with a polyurethane.
The final building step is to lay each plank in place. These will be cut to 20” long each. Attach each piece using wood glue and brad nails. Just make sure the length the nails isn’t longer than the width of the planks and plywood combined. Once you have finished that, you can paint or stain and add your hardware!  Because I was using pre-finished white barn wood from Porter Barn Wood, I painted the table before adding the planks.  Check out these planks…. 
×