“The earliest credible evidence of coffee-drinking appears in the middle of the 15th century in the Sufi shrines of Yemen. It was here in Arabia that coffee seeds were first roasted and brewed, in a similar way to how it is now prepared. Coffee seeds were first exported from Eastern Africa to Yemen, as the coffee plant is thought to have been indigenous to the former.Yemeni traders took coffee back to their homeland and began to cultivate the seed. By the 16th century, it had reached the rest of the Middle East, Persia, Turkey, and northern Africa. From there, it spread to Europe and the rest of the world.” [source]
The sequence in which boards are cut from a log will determine how stable the boards will be once they dry. As a board loses moisture it will shrink in three dimensions. The change in length is so small as to be considered insignificant and the change in radial movement is always less than the tangential movement. This is most significant as the wood dries between the time it's cut (i.e. green wood), and the point where it is kiln dried or air dried and ready for use. Wood that shrinks excessively, or that has been dried improperly, will often develop checks at the ends. When shopping for lumber, carefully inspect the ends for any checking, or for excessively long checks. It is best to allow for some scrap at the end of each board, just in case. As you trim the end, hit the off-cut across the edge of your bench, and if it breaks in two, you'll have to cut off a little more.
A robust media plan further supports Northwest Hardwood’s industry leadership position and further enhances the company’s presence in trade and design media and online spaces. In addition to the traditional customer base, Northwest Hardwoods will also reach architects and designers via a mix of print and digital advertising in publications such as Dwell, Architect Magazine, and Elle Décor. TWIST created a new tagline Keep Pioneering which plays off of the company’s Northwest roots.
The course begins with a quick overview of the history of carpentry, from primitive to modern times. It then teaches you about the most important building materials, fasteners, adhesives, and tools used by carpenters in the modern construction industry. You will then receive an essential outline of safety guidelines and procedures. The course then goes through the crucial steps carpenters must take during construction projects. Here, you will be introduced to the best methods for constructing floor systems, walls, and roof framing, as well as how to make and read plans and elevations. The final section of the course shows you how to close off a structure, including installing windows, exterior doors, and stairs.
The course begins with a quick overview of the history of carpentry, from primitive to modern times. It then teaches you about the most important building materials, fasteners, adhesives, and tools used by carpenters in the modern construction industry. You will then receive an essential outline of safety guidelines and procedures. The course then goes through the crucial steps carpenters must take during construction projects. Here, you will be introduced to the best methods for constructing floor systems, walls, and roof framing, as well as how to make and read plans and elevations. The final section of the course shows you how to close off a structure, including installing windows, exterior doors, and stairs.

Like you, I too am benchless. I built the “Mozilla” Molson vice variant from last year’s issue (I forget which) and it comes in handy for a lot of operations. I clamp it down to a piece of plywood that I have covered with formica (actually, it’s two pieces that I have piano-hinged together for easier storage) laid across two sawhorses. As long as lateral thrust is not involved, this is a pretty stable way to work. I also have a Zyliss vise for working on smaller pieces. I’ve made do for nearly forty years with a radial arm saw and circular saw. I have only recently acquired a planer and router table (both on wheels) It makes the garage croweded because also sharing the space are two motorcycles and about 400 board feet of rough sawn Camphor. I currently attend classes in woodworking and this coming semester I’ll be enrolled in a class for handtools only (and sharpening).
I want to make some wooden boxes and cases, and I haven't done any wood work till now so I don't have any tools and I can't buy the workshop electronic machines which I see in almost every woodworking instructables here (such as drill, lathe, sanding, saw, mitre, buiskit jointer, and all other electronic tools). So I want to begin with simple hand tools.

If desired, add decorative trim pieces to your coffee table. We used an x pattern, but you can leave it as-is if desired. Simply dry fit your pattern into the side panels of your coffee table. Then attach using wood glue and brad nails. After your pieces have been added, fill any holes. Once your wood filler is dry, sand with 120 grit sandpaper. Then stain or paint and finish with a polyurethane.
If you can buy a bunch of tools at one time, you can save a ton on shipping, as the more you buy, the lower the rates. Also, take advantage of free shipping offers. Compare to see where you can get the best deal. Whatever you buy, make sure it is high quality. I have a Nicholson backsaw I bought at a local store before I knew of the woodworking suppliers. It has never been used much, but cuts much slower than saws such as Gramercy or Lie-Nielsen, even though mine have smaller teeth than the Nicholson.
The most commonly purchased claw hammer is the 20 oz. size. It’s heavy enough to easily drive nails but easily manipulated when pulling nails. While wooden handles are picturesque, they may not stand up to the strain if you have to pull a lot of nails. Hammers with a steel handle, or even fiberglass, will be stronger. However, these won’t absorb the vibrations from driving nails the way a hickory handle will. You’ll also need to make sure the fiberglass and metal handles have a rubberized grip for control and comfort. If you’re going to be driving a lot of nails, the wooden handled hammer will be better for reducing stress on your hand, and wrist, too.
The course begins with a quick overview of the history of carpentry, from primitive to modern times. It then teaches you about the most important building materials, fasteners, adhesives, and tools used by carpenters in the modern construction industry. You will then receive an essential outline of safety guidelines and procedures. The course then goes through the crucial steps carpenters must take during construction projects. Here, you will be introduced to the best methods for constructing floor systems, walls, and roof framing, as well as how to make and read plans and elevations. The final section of the course shows you how to close off a structure, including installing windows, exterior doors, and stairs.
Afrormosia Alder Andiroba Anigre Ash Apple Aspen Avodire Balsa Beech Bilinga Birch African Blackwood Australian Blackwood Boxwood Bubinga Camphor Cedrela Cherry Chestnut Cocobolo Cumaru Ebony Elm Eucalyptus Hazel Hickory Hornbeam Idigbo Imbuia Ipê Iroko Jarra Jelutong Lignum vitae Linden (lime, basswood) Merbau Mahogany (American, African) Maple Meranti Oak Padauk Pear Plum Poplar Purpleheart Ovankol Ramin Red Quebracho Rosewood Rubberwood Sapele Teak Totara Utile Walnut Wenge Willow Zebrano
I built my coffee table!! I used the plans at www. EasyWoodwork.org to build mine – highly recommended you check those out too. They are detailed and super easy to read and understand unlike several others I found online. The amount of plans there is mind-boggling… there’s like 16,000 plans or something like that for tons of different projects. Definitely enough to keep me busy with projects for many more years to come haha
Every woodworker needs a couple of levels. You probably won’t need one of the 6-foot levels used in construction, but 48” is a good length for many of the woodworking projects you’ll do. Usually, you’ll also need an 8” level too, usually known as a torpedo level. You’ll check the level and plum of your construction. Level means horizontal, and plumb is vertical.
Residential carpenters specialize in building and remodeling family homes, townhomes, and condominiums. As part of a single job, they might create and set forms for footings, walls, and slabs, and frame and finish exterior walls, roofs, and decks. Additionally, residential carpenters frame interior walls, build stairs, and install drywall, crown molding, doors, and cabinets. They may also tile floors and lay wood floors and carpet.
Treeline offers only the finest wood carving tools and supplies. Everything from Treeline is backed by our 30-day guarantee against any defects. We have been providing wood carving tools since 1997 and we strive to excel in customer service and quality products. All employees at Treeline are very knowledgeable and professional, so if you are looking for the right woodcarving tools, contact us and we will do our best to help you.
Residential carpenters specialize in building and remodeling family homes, townhomes, and condominiums. As part of a single job, they might create and set forms for footings, walls, and slabs, and frame and finish exterior walls, roofs, and decks. Additionally, residential carpenters frame interior walls, build stairs, and install drywall, crown molding, doors, and cabinets. They may also tile floors and lay wood floors and carpet.

By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
Like with most live-edge tables, the hardest part of this project shared on instructables is finding the right slab of wood. It has to have a suitable shape and size for a coffee table top and to look interesting. Cracks, knots and other imperfections help to give it character. Once you have the slab, clean it and apply a protective finish, after which install the legs.
Because the Tabletop is made form several slats of wood, I like to use Figure 8 Top Fasteners to allow the Tabletop boards to expand and contract. To install the fasteners, first mark the placement of each fastener on the apron–I placed three fasteners along each long Apron Board, and two on each End Apron Board. Outline half of the faster on the top edge of the Board.
To best engage with designers and architects, Northwest Hardwoods has expanded its social media reach to include Instagram and Pinterest. Both channels are visually based and aspirational, which will allow Northwest Hardwoods to showcase not only its many types of wood grades and species, but also the beautiful and varied applications for these woods – from cabinets to decking to furniture.

The next hand tool every woodworker should have is a nail set. In fact, you should have several sizes. They look like awls, and you use them to drive nail heads into the wood so they are flush or right below the surface. This allows you to fill the holes and prepare for staining or painting. The nail setter will usually have either a convex or concave surface to grip the nail better and keep it from sliding off and marring the wood.
Carpentry students from Loveland schools who go on to become carpenters, construction managers, construction workers, construction engineers, etc. have a good chance at finding employment. For example, there are 743,760 people working as carpenters alone in the US, and their average annual salary is $43,640. Also, Construction laborers make on average $33,190 per year and there are about 856,440 of them employed in the US today. In fact, in the Fort Collins-Loveland area alone, there are 760 employed construction laborers earning an average salary of $29,460. Carpenters in this area earn $39,170/yr and there are 770 employed.
One subject that a woodworker must always consider when building a project is how seasonal moisture and temperature fluctuations will cause expansion and contraction of the wood stock in the assembled project. For instance, if you've ever experienced a drawer that sticks only in the winter time, you've experienced seasonal movement of wood. Since each wood species is affected by these temperature and moisture fluctuations, you'll need to know a bit about the climate where the project will be used, and how your chosen wood stock is affected by the climate changes. Again, your local woodworking supplier can be a great resource for answering these types of questions in your area.
Lumber for your projects can come from many sources, but before you can use it to build anything, it must be dry. Lumber that is kiln dried will have a moisture content right out of the kiln of 7 or 8%. However, by the time the lumber is delivered to your local dealer and arrives at your shop, the moisture content may have changed dramatically. Storage conditions between the kiln and your shop are clearly out of your control, so it is always a good idea after purchasing lumber to acclimatize it in your shop for several weeks. To avoid using lumber that is still in the process of adjusting to its new environment it is best to use a moisture meter to verify the moisture content of the wood. Most dealers don't mind customers checking the moisture content at the yard as long as they are using a pinless meter. The meter in my lumber kit uses electromagnetic waves to calculate the moisture content of a given piece of wood. Its use couldn't be simpler or quicker – simply turn it on, enter the species, and place the meter on the wood to be measured. The result is displayed right on the screen instantly without the need for conversion tables and other calculations. Typically, I check a couple of areas on each board as I select them just to confirm they are all in the same moisture range. Back at the shop I once more check each piece of wood and note it in chalk on the board. Every few days I'll recheck the boards, and when the readings have stabilized, I can be reasonably certain there won't be any surprises when I start the milling process.
Carpenters craft structures and products from wood, steel, fiberglass and other materials. There are different types of carpenters, including residential, industrial and commercial carpenters. Residential carpenters may build new homes or do remodeling work, building structures like walls, stairways, floors, roofs and decks. Commercial carpenters, who may construct schools, malls and hospitals, use many of the same skills, but they may work more with concrete and steel. Industrial carpenters build infrastructure like tunnels, sewers and dams.
However, if you want to stain or clear-coat the project, you'll have a number of choices to look through. Since your local home center megamart will probably only carry a couple of hardwood species (poplar and red oak are common) spend time at a fine wood supplier and look through the vareties available. They should be able to help you determine how each species will look when finished, which will go a long way toward refining your decision.
Like with most live-edge tables, the hardest part of this project shared on instructables is finding the right slab of wood. It has to have a suitable shape and size for a coffee table top and to look interesting. Cracks, knots and other imperfections help to give it character. Once you have the slab, clean it and apply a protective finish, after which install the legs.
Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!
All Certification is available to purchase through the Alison Shop. For more information on purchasing Alison Certification, please visit our faqs. If you decide not to purchase your Alison Certification, you can still demonstrate your achievement by sharing your Learner Record or Learner Achievement Verification, both of which are accessible from your Dashboard. For more details on our Certification pricing, please visit our Pricing Page.

Commercial carpenters build and remodel commercial office buildings, hospitals, hotels, schools, and shopping malls. Some specialize in light-gauge and load-bearing steel framing for interior partitions, exterior framing, and curtain wall construction. Others specialize in concrete forming systems and finishing interior and exterior walls, partitions, and ceilings.
When I started planning this makeover, I knew I wanted to get rid of the glass coffee table I had and go with something more rustic and cozy… something with beautiful wood grain that looks like it’s been in an old farmhouse somewhere for ages. So rather than searching every single antique store in town or buying something off the shelf at a big box store, I gathered up my tools, picked up some lumber, and made myself a new coffee table!
“Basic,” on the other hand, is a word that allows for growth – and that’s exactly what you want in your woodworking tool kit. You want to be able to take the same kit with you through many years in the craft. With my basic woodworking tools list, I wanted to provide a core set of tools that will serve you well from project to project. I’m especially concerned these days with the transition to hardwood furniture making, as opposed to plywood boxes of various sizes. That’s the transition I’m making right now in my own work!
Carpenters learn many physically-oriented skills, like joining, framing and refinishing. Carpenters also must be adept at measuring and planning to complete the layout portion of their tasks. Errors in this important pre-step to the building process can negatively impact, or even ruin, a finished product. Additionally, mathematical skills and blueprint reading and sketching are vital skills for carpenters.

Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.


Treeline offers only the finest wood carving tools and supplies. Everything from Treeline is backed by our 30-day guarantee against any defects. We have been providing wood carving tools since 1997 and we strive to excel in customer service and quality products. All employees at Treeline are very knowledgeable and professional, so if you are looking for the right woodcarving tools, contact us and we will do our best to help you.

Just a little nitpick on the tape measure blurb. The hook should not be completely tight. It should move in and out about a 1/16th or the thickness of the hook. This way you get an accurate measurement whether you hook a part to measure or bump up to it. If you want more accurate measurements with a tape measure, “burn” an inch instead of hooking or bumping the part. Just line up what you want to measure with the 1″ mark and subtract that inch from the final measurement.

You might not see these tables very often but they were relied on by sheep farmers for many years. Anything that could make the job of shearing sheep easier was welcomed on the farm. You could even change up the plan a little bit by making the legs longer and adding steel (or wooden) wheels to make a merchants cart. That latter idea is something we are suggesting, its not a part of this plan. Joinery methods used primarily in the construction of this sturdy table include mortise and tenon and tongue and groove. View the Larger Image Slideshow to see the actual paper plan you are buying.
×