Apply glue to the ends of the 1 x 2 End Pieces for the Base and Apron, and then clamp them in place against the inside of the Leg. Position the pieces so that one runs flush with the top edge, and the other sets below the line marked in Step 7. Center both pieces on the leg, and tilt them so that they run parallel to the edge of the Leg. Using a drill/driver and 1¼-inch pocket holes screws, attach the pieces to the Leg. Repeat on the opposite end.

Description: You've seen him demo in the store, now come join Rod Hendrickson to learn to carve your own realistic animals. Beginners and carvers of all levels are welcome to join this on-going class. First time students will make a miniature duck decoy. Tuition is for 12 hours of class time. Rough cut outs are supplied by the instructor - check with Rod for cost. (approximately $15 for the miniature duck decoy blank)
Rough lumber is sold and measured in ¼" increments; when a board is referred to as 4/4, it means it is four quarters of an inch thick, or one inch. The most common sizes you are likely to encounter at the lumber yard are 4/4 (1"), 6/4 (1½"), 8/4 (2") and 12/4 (3"). Generally, larger dimension lumber is priced per board foot. Price is also dependant upon the wood quality. Boards without blemishes, and of even colour, command higher prices. On most projects it isn't necessary to purchase the best grade material for the entire project. Purchasing a lower grade will allow you to bring home more lumber, and give you the freedom to lay out parts based on appearance rather than waste.
First, build two boxes for each leg assembly. These are attached using wood glue and 2.5” pocket hole screws through the horizontal boards and into the vertical boards.  You want your pocket holes facing the outside of the box on this part because we will cover them with another board on the next part.  We used our K5 Kreg Jig for this part.  We get asked ALL the time which Kreg Jig to start with.  We always suggest the K5.  We use it on almost every build.  You can find it HERE on Amazon!
Description: Every woodturner enjoys the opportunity to give handmade ornaments to friends and family during the holidays, especially one that is made purely out of wood. No pre-made ornament kits or ornament hardware will be used in this class. One might call it au naturel!!!! During this class you will be given the opportunity to see various ornaments that have been turned on the lathe, ranging from small and simple to large and more decorative. Class objectives include, but are not limited to, the following: Wood choice (more common ornament wood species and pros and cons of each) Discussion and demonstration on how ornaments can be colored using a variety of markers, paints, dyes, and gilder's paste. Discuss and demonstrate how a variety of gouges and tools can be used to make ornaments, including texturing tools. Sharpening techniques - the instructor will assist all students when sharpening tools Ornament rough sketch and design, before the wood is on the lathe. Most important, every student in class will be given the opportunity to turn at least one ornament of their own. The instructor will assist with basic sketch and design, and will rotate among all students to assist with cuts, tool use, technique, sharpening, and helpful hints. Experience level: Beginner (some turning experience highly preferred) Suggested tools: Turning tools will be supplied; however, students are encourage to bring their own tools if they have them. 3/8" or 1/2" spindle gouge, narrow parting tool, and small roughing gouge is a great start. Students who wish to bring their own chuck may do so as well (1"-8 tpi, 2" or 50mm dovetail jaws, and pin jaws). Lunch break from 12:00 to 12:45

From on-time and on-grade products to an unwavering commitment to its customers, Northwest Hardwoods continues to think ahead and lead with high-quality products and approaches to market. The company announced the launch of its new marketing campaign, Lumber Brings Everything to Life at IWF 2018, which unites its two brands – Northwest Hardwoods and the Industrial Timber and Lumber Company (ITL) brand acquired in 2015 – and illustrates the importance, sustainability and natural beauty that lumber holds in each of our daily lives.


Noncredit carpentry courses are offered by numerous commercial websites, some of which are operated by professional carpenters. These courses generally include instructional videos, woodworking glossaries, diagrams and pictures, as well as access to online forums. These courses do not have prerequisites, and all of the websites offer courses starting at the basic level for those new to carpentry.
Framing is another part of carpentry. Framing takes skill and experience it’s not a part of carpentry that anyone can just jump into. The skills that are required in framing is plumbing up a wall, make sure studs are 16 on center or whatever the specs calls for. Developing a good eye for straightness in carpentry work. Last but not least making sure everything is level.
The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.
If you have already completed some college or university education, then many apprenticeship programs will give you credit for prior learning. You can even receive credit for work experience you possess in the construction field. It is important to note that any education and work experience credits will likely be evaluated on a case-by-case basis, so if you want to explore this option, then checking around for the best use of your experience is key.
For over 50 years, American Lumber has earned its reputation for quality, service and dedication to innovation in the hardwood lumber industry. We combine years of hardwood lumber and hardwood log experience with technology and resources to help our customers succeed. Today we provide almost all of the North American hardwood lumber species including red and white oak, ash, cherry, poplar, maple, hickory, alder and walnut. However, we are not just American anymore! We are also a premier provider of imported hardwood lumber from South America, Africa, and Asia...Read More
Typically, a carpentry training program will cover the following subjects: algebra; geometry; physics; hand tool selection, care, and use; architectural drawing; blueprint reading; machine woodworking; identification and measurement of materials; project management and estimating; principles and procedures in residential construction; building code requirements; framing and finishing; building technology; roofing systems; interior and exterior finishing; door and window layout and construction; and mechanical systems.

If creating the coffee table precedes the actual design phase of your interior space, take into consideration future positioning, size and functionality that will determine the addition of storage space.Personalize each piece created from the free coffee table plans featured above and claim it your own. Choose a fun bright tone or paint it Scandinavian white for a calming relaxing effect.Simply fallow the tutorials above and design your perfect coffee table today.


Most carpenter classes and courses lead to a certificate or associate's degree. Graduates can work in many different specialty areas including residential and commercial carpentry. According to the U.S. Bureau of Labor Statistics, 1 in 3 carpenters are self-employed, so some courses include basic business skills for carpenters like cost estimating and project planning. Primarily, however, students will learn about tools, materials and building techniques.
Carpentry is one of the most flexible and versatile construction occupations. As a graduate of a carpentry school online, you may work on a wide variety of projects, both indoors and outdoors—from installing kitchen cabinets and drywall to helping construct large-scale projects from the ground up. That versatility is helping to drive job growth: the U.S. Department of Labor expects carpentry careers to grow 8% by 2026.*

Now that you know how to become a carpenter, you might wonder what the job's like on a day-to-day basis. Because carpentry work demands vigorous exertion, carpenters must be physically fit, strong, and have a good sense of balance. Carpenters must able to work long hours standing, climbing, bending, and kneeling. Additionally, carpenters must be detail-oriented, with good hand-eye coordination and strong problem-solving skills. As carpentry work can be stressful, they must also be able to manage tension and handle workplace pressures. Carpentry work often involves physical risks, like falling and slipping injuries or bruises and cuts from working with sharp tools and rough, heavy materials. Weather conditions and exposure can also pose dangers for carpenters working outdoors.
When you've selected your lumber, restack the pile neatly. Before heading off, calculate the number of board feet you have pulled just to be sure you have enough. It's advisable to allow for errors, waste and slight changes in plan when purchasing your material. Depending on the material and the complexity of the project I'll typically allow from 10 to 40% extra.
Let’s start with perhaps the most basic tool in every household – the claw hammer. The claw on one side of the head should be well counterbalanced by the finished head, which should be somewhat rounded. The other kind of head is the waffle-head. Most commonly used in construction, it leaves a distinctive waffle mark on the wood when you drive the nail. This, of course, is not the proper nail for woodworking.
However, if you want to stain or clear-coat the project, you'll have a number of choices to look through. Since your local home center megamart will probably only carry a couple of hardwood species (poplar and red oak are common) spend time at a fine wood supplier and look through the vareties available. They should be able to help you determine how each species will look when finished, which will go a long way toward refining your decision.
The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.
An associate's degree program can be very valuable if your ultimate goals extend to working in management since many leadership roles require a degree credential in a related field. However, if you are more interested in the hands-on aspect of the profession, then a diploma or certificate program can provide the technical knowledge needed to meet the demands of the job.
I would like to say that the apothecary coffee table is one of the most significant coffee tables in the world. Inspire yourself from old style apothecary coffee tables and make one for your personal from scratch by subsequent a simple step by step seminar. Paint the body of the furniture a washed out white color and let the wooden top unprocessed wood for a best delicate contrast.
Often referred to as Douglas Fir, this wood has a straight, pronounced grain, and has a reddish brown tint to it. Fir is most often used for building; however, it’s inexpensive and can be used for some furniture-making as well. It doesn’t have the most interesting grain pattern and doesn’t take stain very well, so it’s best to use it only when you intend to paint the finished product. Douglas fir is moderately strong and hard for a softwood, rating 4 on a scale of 1 to 4.
Description: This workshop is designed for those who have recently gotten a wood lathe, or have had one for a while, and haven't gotten around to using it until now. During this workshop students get acquainted with the wood lathe and its parts and accessories. We will cover the turning process, as well as sanding and applying finish to a project while it's on the lathe. Students will also be shown a variety of turning tools and how they function. You will also be introduced to wood selection, tool selection, and tool sharpening. Students will test their skills while working on a small turning project. Students should bring suitable eye protection such as safety glasses, goggles, or a face shield. If you have problems with wood dust, a respirator or dust mask would be advisable. Also bring any wood turning tools you might have. Tools and safety gear will be provided for those who don't own them. Materials for turning will be provided.

Scm specializes in designing and manufacturing woodworking machines and services for joineries and customized production shops working with melamine panels, solid wood and other plastic materials. All machines are configured to offer the best technological innovations, high performance and reliability. Easy to install and easy to use, Scm products are distributed all over the world.  

First, build two boxes for each leg assembly. These are attached using wood glue and 2.5” pocket hole screws through the horizontal boards and into the vertical boards.  You want your pocket holes facing the outside of the box on this part because we will cover them with another board on the next part.  We used our K5 Kreg Jig for this part.  We get asked ALL the time which Kreg Jig to start with.  We always suggest the K5.  We use it on almost every build.  You can find it HERE on Amazon!
Hi Alex! I usually only do one coat of stain for darker colors like Dark Walnut. The dark wax doesn’t make a huge difference in the color since the stain is already pretty dark, but I like using wax on furniture to give it more of a natural finish versus a poly. For pieces that get used and abused heavily (like our dining room table) I use a matte finish poly, but for the coffee table wax worked just fine. I hope this helps!
Wood tends to rise its general quality and character with the time passage. I would like to say that water wind rain snow possibly transform its porosity and texture and make it more attractive for a table piece. The attractiveness of this coffee table is the reason behind its mostly utilization. So, you can keep in mind this table as an excellent table.
“Basic,” on the other hand, is a word that allows for growth – and that’s exactly what you want in your woodworking tool kit. You want to be able to take the same kit with you through many years in the craft. With my basic woodworking tools list, I wanted to provide a core set of tools that will serve you well from project to project. I’m especially concerned these days with the transition to hardwood furniture making, as opposed to plywood boxes of various sizes. That’s the transition I’m making right now in my own work!

Somehow I overlook #1, the jointer and thickness planer, and I saw all the other tools and immediately thought that this was my first set of tools I bought when I started working as a carpenter on a friend’s crew. Then I saw my oversight and just couldn’t get over how incongrous those two items were to the rest of the list. Had I seen a scrub plane and a jack plane I would have more harmony in the list.


Residential carpenters specialize in building and remodeling family homes, townhomes, and condominiums. As part of a single job, they might create and set forms for footings, walls, and slabs, and frame and finish exterior walls, roofs, and decks. Additionally, residential carpenters frame interior walls, build stairs, and install drywall, crown molding, doors, and cabinets. They may also tile floors and lay wood floors and carpet.

All Certification is available to purchase through the Alison Shop. For more information on purchasing Alison Certification, please visit our faqs. If you decide not to purchase your Alison Certification, you can still demonstrate your achievement by sharing your Learner Record or Learner Achievement Verification, both of which are accessible from your Dashboard. For more details on our Certification pricing, please visit our Pricing Page.
Certain species of wood have traditionally been associated with different styles of furniture. The wood of choice for the Arts & Crafts movement was quarter sawn white oak, valued for its appearance, durability and dimensional stability. An Arts & Crafts style piece executed in maple might be a well-made example of a classic style, but the choice of wood would be visually at odds with the design. Pine and other softwoods impart a more relaxed, country influence, while traditional hardwoods, such as cherry and walnut, are more likely to be associated with fine furniture.
We cut the decorative diagonal pieces to fit on this part. Mark each board with your pencil and cut them to fit exact. You can check out the video if you have questions about this part! We walk you through it. Cut the diagonal pieces to fit first, then mark and attach them to each other using wood glue and nails. Then, fit them in the box and attach them with wood glue and nails through the box and into each end of the X piece.
Not all species are available in quarter sawn form from all dealers, but it can be possible to cut parts from wider boards to accomplish the same end. At the lumberyard I will often look for wider planks for this very reason. When a wide board is cut from the log it will have some vertical grain on the outer edges and some face grain in the center of the board. By purchasing enough stock and carefully laying out the parts it would be possible to use quarter sawn material for all visible parts. Decisions like this must often be made at the lumberyard based on the stock on hand. It is a way to stretch your material budget a little further, by buying a lower grade and resawing it for appearance back in the shop.
I’m currently working on a dining room table with this color in mind (I also plan on a coffee table soon). I’ve been testing out stain colors and dark walnut is currently in the lead. I love the way this coffee table turned out in color. How many coats of stain did you use? Also, did the dark wax make a big difference in color? I was planning on using a satin poly for sealant (mostly because it’s what is most convenient and what I’m accustomed to), but I’m interested in the dark wax after seeing this post. Any recommendations you have are much appreciated.
The staff of WOODWEB assume no responsibility for the accuracy, content, or outcome of any posting transmitted at WOODWEB's Message Boards. Participants should undertake the use of machinery, materials and methods discussed at WOODWEB's Message Boards after considerate evaluation, and at their own risk. WOODWEB reserves the right to delete any messages it deems inappropriate. (return to top)
I am looking to buy some wood to build a swinging bench for our backyard. For this project, I want to make sure I find the right wood that will be durable, especially with all the different outdoor elements it will be facing. I didn’t realize that wood expands in width with humidity, but we will certainly have to look for stable lumber. Thanks for sharing!
What’s better than a coffee table? Well…two coffee tables. You can put them one on top of the other and make a two-tier table like this one. The idea is both interesting and practical. If you want you could find a way to make the two tiers detachable so you can use them separately whenever you want. Of course, apart from the unusual structure, this table also stands out thanks to its eye-catching color block design. {found on akailochiclife}.
Cherry is a very popular and all-around great wood; easy to work with, stains and finishes well with just oil, and ages beautifully. Cherry’s heartwood has a reddish-brown color to it and the sapwood is almost white. Cherry has a hardness of 2 on a scale of 1 to 5. This is a very common wood for furniture-making and is available from sustainably grown forests. You won’t find cherry at your local home center, so a trip to the lumberyard is necessary if you want to use it. Because it’s in demand, cherry is getting somewhat expensive compared to other domestic hardwoods, such as oak and maple.
Having completed this course the learner will be able to: - Describe the history and scope of carpentry as a trade; - Identify the opportunities for carpenters in the construction industry; - Classify the various building materials used by carpenters; - List the most commonly used fasteners and adhesives used by people in the carpentry trade; - Explain the different types of hand and power tools available to carpenters; - Outline the general safety procedures and guidelines that should be followed to operate the tools; - Discuss the importance of employee responsibility and human relations to being successful in the trade; - Identify the various types of construction drawings that make a drawing set; - State the guidelines to read and interpret reading plans and drawings, blueprints, and specifications; - List the various terms associated with floor systems, wall, ceiling and roof framing; - Explain the different methods of framing and constructing houses made of wood; - Describe the types of beams/girders and supports used in construction; - Outline the sequence involved in constructing a platform floor assembly; - Summarize the basic procedure for laying out, assembling, and erecting wood frame walls; - Recognize the different types of roofs used in residential construction; - Determine the length of a common rafter required to construct a roof; - Discuss the terms associated with concrete, concrete reinforcing materials, and formwork; - Apply the concrete mixing information to get different types of concrete, designed to suit various purposes; - Explain the basic concrete curing methods and materials; - List the various components of windows, exterior doors, and stairways used in residential construction; - Summarize the basic installation procedure for pre-hung windows; - State the various types of exterior doors used in residential construction; - Identify the essential requirements for framing stairs; - Describe the design and layout techniques used for stairways and stairwells.
This woodworking plans project is a Bentwood Coffee Table that is a challenging design for those who would like to try a project which requires wood bending. The contemporary lines combined with traditional natural wood allow this table to fit comforatbly with many other styles of furnishings. The technique for bending the wood does not require any special tools or steaming processes.
Not only for utility purposes, the coffee tables also play a vital role in boosting decors and storage space of a living room! People can use the coffee tables with built-in secret stashes or with lift-tops if they need some extra storage space in their living room! By adding a glass top or a flower vase to the top of a coffee table, one can also turn it into a living room centerpiece! In short, missing a coffee table in the living room would not be appreciated in any way as it is the very first demand and need for a living room! So make you get to your favorite coffee table easily we have shared here this flawless list of 20 DIY coffee table plans that can be made at home! All these tables are style-worthy, sturdy and inexpensive!
At Able Skills we pride ourselves in the diversity of the skills that are available within our carpentry training centre. If upon completion of this course you would like to learn much more then you can consider upgrading to City & Guilds Certificate & Training to NVQ Level 2. This would require you to train for an additional 5 weeks; payment would be adjusted to reflect what you have already paid on this course.

I want to make some wooden boxes and cases, and I haven't done any wood work till now so I don't have any tools and I can't buy the workshop electronic machines which I see in almost every woodworking instructables here (such as drill, lathe, sanding, saw, mitre, buiskit jointer, and all other electronic tools). So I want to begin with simple hand tools.
All trees share common growth characteristics (annual growth rings, branches, sap, etc.), but these individual characteristics vary widely from one species to another. Different species have marked variations in the characteristics of their wood. For example, ash wood is pale with wide, open grain, while cherry wood is reddish brown with fine, closed grain. It is these variations that give each species its unique characteristics, making them suitable for one job and unsuitable for another. Wood falls into one of two categories, either softwood or hardwood, though it could be argued that the categories might better be labelled "Wood I can afford" and "Wood I can only dream about". Generally, coniferous trees fall into the softwood category, and deciduous into the hardwood.

1: Table saw in place of a jointer. Any number of tips in previous issues address straightening edges of boards without a jointer. A jointer serves one purpose, but a tablesaw can serve many (just watch your local Craigslist for a decent one to come up.) The thickness planer is unavoidable, but until you can afford one, buy stock in the thickness you need.
Carpentry students from Loveland schools who go on to become carpenters, construction managers, construction workers, construction engineers, etc. have a good chance at finding employment. For example, there are 743,760 people working as carpenters alone in the US, and their average annual salary is $43,640. Also, Construction laborers make on average $33,190 per year and there are about 856,440 of them employed in the US today. In fact, in the Fort Collins-Loveland area alone, there are 760 employed construction laborers earning an average salary of $29,460. Carpenters in this area earn $39,170/yr and there are 770 employed.
You might not see these tables very often but they were relied on by sheep farmers for many years. Anything that could make the job of shearing sheep easier was welcomed on the farm. You could even change up the plan a little bit by making the legs longer and adding steel (or wooden) wheels to make a merchants cart. That latter idea is something we are suggesting, its not a part of this plan. Joinery methods used primarily in the construction of this sturdy table include mortise and tenon and tongue and groove. View the Larger Image Slideshow to see the actual paper plan you are buying.
×