2 small Japanese pull saws, a western push saw, fret saw, set of chisels, bit brace with a roll of arbor bits, rabbet plane, side rabbet (trim) plane, 2 shoulder planes, 3 set of diamond stones, slip stone, multiple files, a rasp or two, 2 small bar clamps, a mini vise, hand scrapers, scratch beader with cutters, combination plane with cutters, smoothing plane, jack plane, block plane, combination square, steel straight rule, 12′ tape measure, small bottle of glue, a few short dowels, 2 marking gauges, and a few different marking instruments (awl, pencils, marking knife).
Some moisture meters have pins that penetrate the surface of the wood. This can leave tiny holes that mar the surface and require filling. Others are pin-less. They have sensing plates that scan the wood beneath. However, not all pinless moisture meters are the same – look for one that uses technology that is not affected by the surface moisture in the wood, such as Wagner Meters IntelliSense™ Technology Moisture Meters.

When I started planning this makeover, I knew I wanted to get rid of the glass coffee table I had and go with something more rustic and cozy… something with beautiful wood grain that looks like it’s been in an old farmhouse somewhere for ages. So rather than searching every single antique store in town or buying something off the shelf at a big box store, I gathered up my tools, picked up some lumber, and made myself a new coffee table!
More than a year ago, before I joined the staff, Megan Fitzpatrick and I talked about an article I wanted to write about lumberyards and the perennial discussion about domestic versus exotic lumber. At the time, I was also working on an interactive map of New York City’s neighborhoods, and I floated the idea of creating a map of local lumberyards that would accompany the article.

Rip your 1x4's so they are 3" wide. This should make them nice and square, so they fit together without any gaps or rounded edges. Drill pocket holes in both ends of each board. Drill several pocket holes (3 or 4) on the edges of each board. Spread wood glue on the edges of each board, and sandwich them together, using bar clamps to keep them tight. Using 1 1/4" pocket hole screws, attach the 1x4's together. (see photo on next step)


Some moisture meters have pins that penetrate the surface of the wood. This can leave tiny holes that mar the surface and require filling. Others are pin-less. They have sensing plates that scan the wood beneath. However, not all pinless moisture meters are the same – look for one that uses technology that is not affected by the surface moisture in the wood, such as Wagner Meters IntelliSense™ Technology Moisture Meters.
Students learn the basics of residential house framing, including layout techniques, roof and wall framing, planning for windows and doors and the pouring of a foundation. Following classroom instruction in basic carpentry math and materials estimation, students have the opportunity to employ their carpentry skills by working together on a residential building project. Teamwork, workplace ethics, craftsmanship and punctuality are emphasized in the practical portion of the course.
Even if you are using a beautiful (yet unstable) grain pattern on part of your furniture, it’s a good idea to use stable wood on the other parts. For example, look at an old wooden door. The panels usually have more decorative (less stable) wood, but the rails and stiles (parts of the frame) are usually very stable straight grained wood (don’t worry, I’ll clarify “straight grain” below).
Carpenters are skilled craftspersons who create structures and consumer goods from common materials, like wood and concrete. Enrolling in carpentry courses at a trade school or community college is one way to gain the knowledge and techniques needed for a career as a carpenter. Skills learned in carpentry courses may include safety awareness, building layout design and blueprint reading. Continue reading for more information about carpentry courses. Schools offering Carpentry degrees can also be found in these popular choices.
Carpentry skills can be applied to residential or commercial remodeling, cabinet making and exterior and interior trim. Coursework in carpentry classes commonly includes instruction in building safety, construction codes, framing and site layout. These courses are widely available at technical schools and colleges. Hands-on practice is emphasized in most classes.
You might be able to enroll in a General Contractor's License Preparation Certificate, a Carpentry Diploma or a Career Diploma in Carpentry program, among other options. Programs might require a high school diploma or its equivalent and a placement test. The programs may prepare you for entry-level positions in industry, engineering and the construction trades. The following topics might be covered in a carpentry or contracting program:
Coffee tables are more of a North American furniture piece, you typically will not find these in England, for which this coffee table is designed after. With a country-style look and rugged appearance of an old workbench, the tapered legs and deep v-grooves on the top with breadboard ends given the appearance of strength and durability. View the Larger Image Slideshow to see the actual paper plan you are buying.
Apply glue to the ends of the 1 x 2 End Pieces for the Base and Apron, and then clamp them in place against the inside of the Leg. Position the pieces so that one runs flush with the top edge, and the other sets below the line marked in Step 7. Center both pieces on the leg, and tilt them so that they run parallel to the edge of the Leg. Using a drill/driver and 1¼-inch pocket holes screws, attach the pieces to the Leg. Repeat on the opposite end.
This course introduces students to remodeling practices and demolitions. Students learn how to plan a remodeling project, complete basic plumbing and electrical jobs, apply for permits, match finished materials and estimate costs. Instruction in reading architectural blueprints for residential remodels is generally included, and students become familiar with specifications, codes and construction drawings. Some residential remodeling courses provide hands-on learning experience by requiring group or individual remodeling projects. This course is usually taken after basic carpentry courses.
There are three very important elements that must come together in making a project that will not only be pleasing to the eye, but will stand the test of time: good design, careful workmanship and meticulous selection of materials. You can continue to refine your design on paper, but at some point you will have to make that transition from a two dimensional drawing to selecting the lumber to use for each part. This can be one of the most difficult phases of any project and one that has the greatest effect on the final appearance of your finished piece.

The sequence in which boards are cut from a log will determine how stable the boards will be once they dry. As a board loses moisture it will shrink in three dimensions. The change in length is so small as to be considered insignificant and the change in radial movement is always less than the tangential movement. This is most significant as the wood dries between the time it's cut (i.e. green wood), and the point where it is kiln dried or air dried and ready for use. Wood that shrinks excessively, or that has been dried improperly, will often develop checks at the ends. When shopping for lumber, carefully inspect the ends for any checking, or for excessively long checks. It is best to allow for some scrap at the end of each board, just in case. As you trim the end, hit the off-cut across the edge of your bench, and if it breaks in two, you'll have to cut off a little more.
When you've selected your lumber, restack the pile neatly. Before heading off, calculate the number of board feet you have pulled just to be sure you have enough. It's advisable to allow for errors, waste and slight changes in plan when purchasing your material. Depending on the material and the complexity of the project I'll typically allow from 10 to 40% extra.
Hardwoods come from deciduous, or broad-leaved trees, as opposed to softwoods, that are harvested from from evergreens. In general, the lumber derived from hardwood species are typically harder than softwoods, although there are exceptions (balsa wood is very light and soft, but is considered a hardwood). Most hardwood tree species lose their leaves in winter, and generally offer a much wider variety of colors and textures than softwoods. Typically, stock from hardwood species are a lot more expensive than those from softwoods.
A successful joiner can see the full picture of the project he is preparing to run and for SCM woodworking machinery come to his aid with devices made especially for woodworking machinery; devices that allow to not having to perform the mathematical calculations necessary to make a precise angular cut on a circular saw (with our compex for example) or a template that can produce pieces that are exactly identical among them (on our lathe minimax t 124).
×