Thread Related Link and Image Guidelines Thread Related Links posted at WOODWEB's Forums and Exchanges should point to locations that provide supporting information for the topic being discussed in the current message thread. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related Link that directs visitors to an area with inappropriate content will be removed. WOODWEB reserves the right to delete any messages with links or images it deems inappropriate. (return to form)
Once the vinegar solution dries (or if you decided not to do the solution) you can go ahead and stain the project. First use a rag or air compressor to remove any dust from the table. Then use a clean rag to apply the stain of your choice. Don't forget to wear gloves and ventilate the area. Have a brush in your other hand to stain hard to reach areas.
To us it is clear: Power, passion and conviction in the process of creation is what drives us and makes us so successful. The common objective is this, both today and for the future, to build the best woodworking machines with respect for our customers and for our environment. This is reinforced with each machine that leaves our factory in Hall in Tirol.
Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!

The course begins with a quick overview of the history of carpentry, from primitive to modern times. It then teaches you about the most important building materials, fasteners, adhesives, and tools used by carpenters in the modern construction industry. You will then receive an essential outline of safety guidelines and procedures. The course then goes through the crucial steps carpenters must take during construction projects. Here, you will be introduced to the best methods for constructing floor systems, walls, and roof framing, as well as how to make and read plans and elevations. The final section of the course shows you how to close off a structure, including installing windows, exterior doors, and stairs.


I’m currently working on a dining room table with this color in mind (I also plan on a coffee table soon). I’ve been testing out stain colors and dark walnut is currently in the lead. I love the way this coffee table turned out in color. How many coats of stain did you use? Also, did the dark wax make a big difference in color? I was planning on using a satin poly for sealant (mostly because it’s what is most convenient and what I’m accustomed to), but I’m interested in the dark wax after seeing this post. Any recommendations you have are much appreciated.

Products and systems by Lamello have always been Products and systems by Lamello have always been designed for longevity and reliability. This legendary durability is combined with environmental stewardship in view as strict environmental regulations at our production site in Switzerland ensure that all resources are used with consideration many of them stemming from sustainable husbandry and management. ...  More + Product Details Close


Carpenters craft structures and products from wood, steel, fiberglass and other materials. There are different types of carpenters, including residential, industrial and commercial carpenters. Residential carpenters may build new homes or do remodeling work, building structures like walls, stairways, floors, roofs and decks. Commercial carpenters, who may construct schools, malls and hospitals, use many of the same skills, but they may work more with concrete and steel. Industrial carpenters build infrastructure like tunnels, sewers and dams.
Description: This workshop is designed for those who have recently gotten a wood lathe, or have had one for a while, and haven't gotten around to using it until now. During this workshop students get acquainted with the wood lathe and its parts and accessories. We will cover the turning process, as well as sanding and applying finish to a project while it's on the lathe. Students will also be shown a variety of turning tools and how they function. You will also be introduced to wood selection, tool selection, and tool sharpening. Students will test their skills while working on a small turning project. Students should bring suitable eye protection such as safety glasses, goggles, or a face shield. If you have problems with wood dust, a respirator or dust mask would be advisable. Also bring any wood turning tools you might have. Tools and safety gear will be provided for those who don't own them. Materials for turning will be provided.
Disclaimer: Almost any DIY project involves risk of some sort. Your tools, materials, and skills will vary, as will the conditions at your project site. Rogue Engineer has made every effort to be complete and accurate in the instructions provided on this website. Rogue Engineer will not assume any responsibility or liability for damages or losses sustained or incurred in the course of your project or in the use of the item you create. Always follow the manufacturer's operating instructions in the use of tools, check and follow your local building codes, and observe all commonly accepted safety precautions.
You will perfect your marking, cutting and chiseling skills by making a series of common woodwork joints each joint being that little bit more difficult than the last. These skills will come in for later during the course when you will be required to chop in hinges using a chisel into a door and door frame plus build a door frame with a half lap joint.
When you've selected your lumber, restack the pile neatly. Before heading off, calculate the number of board feet you have pulled just to be sure you have enough. It's advisable to allow for errors, waste and slight changes in plan when purchasing your material. Depending on the material and the complexity of the project I'll typically allow from 10 to 40% extra.

A successful joiner can see the full picture of the project he is preparing to run and for SCM woodworking machinery come to his aid with devices made especially for woodworking machinery; devices that allow to not having to perform the mathematical calculations necessary to make a precise angular cut on a circular saw (with our compex for example) or a template that can produce pieces that are exactly identical among them (on our lathe minimax t 124).

Make sure that as you work with machinery, you are wearing a face shield or safety goggles. If you are exposed to noise, use hearing protection to match the level of noise production. Gloves can protect your hands from splinters. If your woodworking machinery has a cover to protect the start and stop buttons, it is advisable to obtain one for yourself. This will protect the start buttons so that you do not accidentally activate machines.
Hands-on techniques are generally introduced in this course, which covers exterior moisture, interior and exterior doors, window trim installation and custom built-in cabinetry. When studying interior finish features, students learn about sheet rock, taping and texturing and cabinet installation. Coursework on exterior finish features may include estimating time and costs, framing, laying out rafters for roofs and installing outside doors and windows. This course is taken after introductory courses.
Hi Alex! I usually only do one coat of stain for darker colors like Dark Walnut. The dark wax doesn’t make a huge difference in the color since the stain is already pretty dark, but I like using wax on furniture to give it more of a natural finish versus a poly. For pieces that get used and abused heavily (like our dining room table) I use a matte finish poly, but for the coffee table wax worked just fine. I hope this helps!
More than a year ago, before I joined the staff, Megan Fitzpatrick and I talked about an article I wanted to write about lumberyards and the perennial discussion about domestic versus exotic lumber. At the time, I was also working on an interactive map of New York City’s neighborhoods, and I floated the idea of creating a map of local lumberyards that would accompany the article.
A Guide to Honing and Sharpening helps woodworkers keep their tools in the best possible working condition. It focuses on the history of honing and sharpening and vital aspects of these practices, such as stropping, beveling, chiseling, flattening and other modern technological methods. Students can explore these methods via text, pictures and diagrams.
The final building step is to lay each plank in place. These will be cut to 20” long each. Attach each piece using wood glue and brad nails. Just make sure the length the nails isn’t longer than the width of the planks and plywood combined. Once you have finished that, you can paint or stain and add your hardware!  Because I was using pre-finished white barn wood from Porter Barn Wood, I painted the table before adding the planks.  Check out these planks….
×