The most commonly purchased claw hammer is the 20 oz. size. It’s heavy enough to easily drive nails but easily manipulated when pulling nails. While wooden handles are picturesque, they may not stand up to the strain if you have to pull a lot of nails. Hammers with a steel handle, or even fiberglass, will be stronger. However, these won’t absorb the vibrations from driving nails the way a hickory handle will. You’ll also need to make sure the fiberglass and metal handles have a rubberized grip for control and comfort. If you’re going to be driving a lot of nails, the wooden handled hammer will be better for reducing stress on your hand, and wrist, too.
Thank you so much, Fawn!! I think using pocket holes to connect the top boards is a fantastic idea, and we actually did that with the bigger dining room table we did a few weeks ago. For our coffee table, I kind of liked the look of small gaps in between each board… gives it a more rustic look I think! 🙂 Have fun building your table… I’d love to see it! Tag me on Instagram!
This is a vintage woodworking plan. Visit our FAQ page for a full definition. View the Larger Image Slideshow to see the actual item you are buying. A fine new design just added to our Colonial group is the Wagon Seat Coffee table, patterned in full-size. You will admire its beautiful lines and appreciate its sturdy construction. The well shaped, open gallery and four shelf pegs add to its appearance. Its two drawers are handy for small storage, and the shelves are useful for holding a few magazines or books. Build it of pine or hardwood and finish it with a stain and lacquer of high quality. Then wax it and rub it, and you will have a piece of furniture that will mellow as it improves with time.
Integrating a planter into a table is actually a pretty common idea. We’ve seen quite a few projects which include this feature and one of them comes from abeautifulmess. Check out the plans to find out how to put together with a minimalist and stylish coffee table with a planter at its center. You can use that space as a herb garden or you can plant grass or succulents in there. We really the crisp and linear design, the pureness of the white body and the strong contrast with the black legs and the green of the plants. It’s refreshing in a very special way.
I’m currently working on a dining room table with this color in mind (I also plan on a coffee table soon). I’ve been testing out stain colors and dark walnut is currently in the lead. I love the way this coffee table turned out in color. How many coats of stain did you use? Also, did the dark wax make a big difference in color? I was planning on using a satin poly for sealant (mostly because it’s what is most convenient and what I’m accustomed to), but I’m interested in the dark wax after seeing this post. Any recommendations you have are much appreciated.
While flipping through the boards, keep an eye open for signs that a number of boards may have come from the same tree. Looking at the ends and the growth rings will tell you where in the log the board was sawn. In some cases, knots may go through more than one board, and often the outer boards have a live edge. By comparing these features, the colouring, grain and other distinguishing marks, it is often possible to identify several boards cut from the same log.
These machines are used both in small-scale commercial production of timber products and by hobbyists. Most of these machines may be used on solid timber and on composite products. Machines can be divided into the bigger stationary machines where the machine remains stationary while the material is moved over the machine, and hand-held power tools, where the tool is moved over the material.
Wow, what a great problem to have Boris! If you can send some photos I’ll look at them. But unseen, I’d ask them to try to get some quartersawn boards out, and also some full width flatsawn boards. It just depends on how much wood you’ll get if you quartersaw it. It also depends on what you think you’ll build down the road. Some furniture pieces don’t need to be quite as stable as others. Good luck!
Real quick story: Recently, I had to help my brother with some furniture and cabinet issues, but there were a few problems. First he lived 3 hours by car and my wife needed our only car. I’ve had a scooter for a few years, but have only used it for local trips with small needs. Since weather was changing and I needed a break away from my other half, I decided to make the trip. I installed my motorcycle saddlebags to the scooter and loaded the necessary tools for the trip. Where’s the motorcycle? That’s another story. Of course the saddlebags are small and the scooter only had a massive 50cc engine; vrmm, vrmm. Although I have a shop full of electric and traditional hand tools, only the smaller hand tools would make the list for this trip. So, here is the list from that trip: (A few may be missing)
I just moved overseas and had to give up all of my power tools due to space limitations and power incompatibility. Upon arrival the first power tool that I bought was a cordless drill/driver and the second was a circular saw. I then modified the saw to improve its performance for cabinet quality work by putting a zero clearance baseplate (just a piece of 1/4″ plywood screwed to the base) this allows the saw to cut plywood panels without tearing up the edges. I also bought a length of aluminum rectangle tube stock for a straight edge. Together the straight edge and the zero clearance baseplate makes the circular saw a fairly accurate tool for plywood construction projects. It’s not as easy to use as a Festool track saw but it cuts almost as clean and cost about 1/5th the price.
You will perfect your marking, cutting and chiseling skills by making a series of common woodwork joints each joint being that little bit more difficult than the last. These skills will come in for later during the course when you will be required to chop in hinges using a chisel into a door and door frame plus build a door frame with a half lap joint.
You might be able to enroll in a General Contractor's License Preparation Certificate, a Carpentry Diploma or a Career Diploma in Carpentry program, among other options. Programs might require a high school diploma or its equivalent and a placement test. The programs may prepare you for entry-level positions in industry, engineering and the construction trades. The following topics might be covered in a carpentry or contracting program:
No matter what type of wood working equipment you are looking for, Hermance is here to help. We offer one of the largest selections of general woodworking machinery online. Whether you're in the market for a boring machine, table saw, dust collector, or even an end matcher- you're sure to find what you're looking for in our listings of general woodworking machinery.
1: Table saw in place of a jointer. Any number of tips in previous issues address straightening edges of boards without a jointer. A jointer serves one purpose, but a tablesaw can serve many (just watch your local Craigslist for a decent one to come up.) The thickness planer is unavoidable, but until you can afford one, buy stock in the thickness you need.
Treeline offers only the finest wood carving tools and supplies. Everything from Treeline is backed by our 30-day guarantee against any defects. We have been providing wood carving tools since 1997 and we strive to excel in customer service and quality products. All employees at Treeline are very knowledgeable and professional, so if you are looking for the right woodcarving tools, contact us and we will do our best to help you.
Products and systems by Lamello have always been Products and systems by Lamello have always been designed for longevity and reliability. This legendary durability is combined with environmental stewardship in view as strict environmental regulations at our production site in Switzerland ensure that all resources are used with consideration many of them stemming from sustainable husbandry and management. ...  More + Product Details Close

One subject that a woodworker must always consider when building a project is how seasonal moisture and temperature fluctuations will cause expansion and contraction of the wood stock in the assembled project. For instance, if you've ever experienced a drawer that sticks only in the winter time, you've experienced seasonal movement of wood. Since each wood species is affected by these temperature and moisture fluctuations, you'll need to know a bit about the climate where the project will be used, and how your chosen wood stock is affected by the climate changes. Again, your local woodworking supplier can be a great resource for answering these types of questions in your area.


I built my coffee table!! I used the plans at www. EasyWoodwork.org to build mine – highly recommended you check those out too. They are detailed and super easy to read and understand unlike several others I found online. The amount of plans there is mind-boggling… there’s like 16,000 plans or something like that for tons of different projects. Definitely enough to keep me busy with projects for many more years to come haha

At the core of the campaign is a new website, which immerses customers in a user-friendly, easy-to-navigate, and informative user experience. Site visitors will find new photography and video, product-specific pages featuring detailed descriptions, a timeline recounting the company’s history, sales maps, and a monthly blog. Built with the future in mind, the site’s foundation allows for the eventual expansion to include real-time inventory tracking, sample requests, and more.
The beverage pallet coffee table is one of the most significant choices for your living room if you live to entertain. It comprises a built-in space for the bucket of the ice storage that possibly keeps your drinks fresh and cold, space which can be tucked away and be covered up when necessary. In this case beverage pallet coffee table is best for you.
Use a polyurathane ( I used a Minwax Semi-Gloss ) to seal and protect the finished coffee table. Apply the 1st coat of polyurethane to the entire table. Once dry, add a second coat to the table top. I only generally do one coat of poly on the base. Once the second coat has dried take a sanding block with 400 grit sandpaper and lightly sand all areas you've poly'ed. Then take a clean damp rag to remove the dust and prepare for your final coat of poly.
More than a year ago, before I joined the staff, Megan Fitzpatrick and I talked about an article I wanted to write about lumberyards and the perennial discussion about domestic versus exotic lumber. At the time, I was also working on an interactive map of New York City’s neighborhoods, and I floated the idea of creating a map of local lumberyards that would accompany the article.
Apply glue to the ends of the 1 x 2 End Pieces for the Base and Apron, and then clamp them in place against the inside of the Leg. Position the pieces so that one runs flush with the top edge, and the other sets below the line marked in Step 7. Center both pieces on the leg, and tilt them so that they run parallel to the edge of the Leg. Using a drill/driver and 1¼-inch pocket holes screws, attach the pieces to the Leg. Repeat on the opposite end.
Use a polyurathane ( I used a Minwax Semi-Gloss ) to seal and protect the finished coffee table. Apply the 1st coat of polyurethane to the entire table. Once dry, add a second coat to the table top. I only generally do one coat of poly on the base. Once the second coat has dried take a sanding block with 400 grit sandpaper and lightly sand all areas you've poly'ed. Then take a clean damp rag to remove the dust and prepare for your final coat of poly.
All Certification is available to purchase through the Alison Shop. For more information on purchasing Alison Certification, please visit our faqs. If you decide not to purchase your Alison Certification, you can still demonstrate your achievement by sharing your Learner Record or Learner Achievement Verification, both of which are accessible from your Dashboard. For more details on our Certification pricing, please visit our Pricing Page.

I’m currently working on a dining room table with this color in mind (I also plan on a coffee table soon). I’ve been testing out stain colors and dark walnut is currently in the lead. I love the way this coffee table turned out in color. How many coats of stain did you use? Also, did the dark wax make a big difference in color? I was planning on using a satin poly for sealant (mostly because it’s what is most convenient and what I’m accustomed to), but I’m interested in the dark wax after seeing this post. Any recommendations you have are much appreciated.


Suppose you you were in possession of, as I am, four Cherry logs ranging in size from 18″ to 24″ diameter by 12′ to 16′ in length and you need to instruct the sawmill how they are to be cut. Also suppose that you are a novice woodworker who intends to use the resulting lumber in undetermined woodworking projects. How would you instruct the mill to cut up the logs?
Poplar is one of the less expensive hardwoods. It’s also fairly soft (1 in hardness on a scale of 1 to 5), which makes it easy to work with. Poplar is white with some green or brown streaks in the heartwood. Because poplar is not the most beautiful wood, it’s rarely used in fine furniture, and if it is, it’s almost always painted. Poplar can be a good choice for drawers (where it won’t be seen) because it is stable and inexpensive. You can find poplar at larger home centers, but a lumberyard will have a better selection.

Home Site Map What's New New Visitors Video Library Software & Mobile Apps Auctions, Sales and Special Offers Industry News Woodworkers Directory Sawing and Drying Directory The Wood Doctor Bookstore Lumber Buying Guide Tradeshow Directory Newsstand Lumber/Timber/Misc Calculators Events Calendar Media Kit Poll Center About WOODWEB What Our Visitors Say Frequently Asked Questions Contact WOODWEB User Agreement and Terms of Use Privacy Policy Link to WOODWEB Refer a Friend Subscribe to the WOODWEB Update Update Archive Become a Member
Scm specializes in designing and manufacturing woodworking machines and services for joineries and customized production shops working with melamine panels, solid wood and other plastic materials. All machines are configured to offer the best technological innovations, high performance and reliability. Easy to install and easy to use, Scm products are distributed all over the world. 
Students learn the basics of residential house framing, including layout techniques, roof and wall framing, planning for windows and doors and the pouring of a foundation. Following classroom instruction in basic carpentry math and materials estimation, students have the opportunity to employ their carpentry skills by working together on a residential building project. Teamwork, workplace ethics, craftsmanship and punctuality are emphasized in the practical portion of the course.
The lumber industry uses the “Janka hardness test” to test and rate common woods for hardness. The test involves pressing a steel ball to gauge how much pressure each wood species takes to push the ball half way into the wood. You can download my free PDF of the Janka chart here. {If you can’t open a PDF then install the free Adobe PDF Reader here.}

A Guide to Honing and Sharpening helps woodworkers keep their tools in the best possible working condition. It focuses on the history of honing and sharpening and vital aspects of these practices, such as stropping, beveling, chiseling, flattening and other modern technological methods. Students can explore these methods via text, pictures and diagrams.
To best engage with designers and architects, Northwest Hardwoods has expanded its social media reach to include Instagram and Pinterest. Both channels are visually based and aspirational, which will allow Northwest Hardwoods to showcase not only its many types of wood grades and species, but also the beautiful and varied applications for these woods – from cabinets to decking to furniture.
Make sure that as you work with machinery, you are wearing a face shield or safety goggles. If you are exposed to noise, use hearing protection to match the level of noise production. Gloves can protect your hands from splinters. If your woodworking machinery has a cover to protect the start and stop buttons, it is advisable to obtain one for yourself. This will protect the start buttons so that you do not accidentally activate machines.
1: Table saw in place of a jointer. Any number of tips in previous issues address straightening edges of boards without a jointer. A jointer serves one purpose, but a tablesaw can serve many (just watch your local Craigslist for a decent one to come up.) The thickness planer is unavoidable, but until you can afford one, buy stock in the thickness you need.

Description: In this four day class, we will start with rough lumber and finish with a simple box. Along the way we will teach you how to use the jointer, planer, table saw, and router table This is THE class to take if you are interested in getting started the right way in woodworking. This one will fill up fast, so sign up. soon. Woodworking 101 is strongly recommended for beginners and people looking to review the basics.


I've found that it is easiest to attach the shelf by attaching the 2×2 side rails prior to connecting it to the table. To do this you'll sort of take a minor step back by removing the two lower 2×2 side rails (only 8 screws). Then drill the shelf to the 2×2's as shown below. Lift the shelf into place and attach each end of the shelf to the lower end rails using 2 1/2″ Kreg Screws. Once that is secure flip the table right side up and add the cross supports.
All Certification is available to purchase through the Alison Shop. For more information on purchasing Alison Certification, please visit our faqs. If you decide not to purchase your Alison Certification, you can still demonstrate your achievement by sharing your Learner Record or Learner Achievement Verification, both of which are accessible from your Dashboard. For more details on our Certification pricing, please visit our Pricing Page.
I’m currently working on a dining room table with this color in mind (I also plan on a coffee table soon). I’ve been testing out stain colors and dark walnut is currently in the lead. I love the way this coffee table turned out in color. How many coats of stain did you use? Also, did the dark wax make a big difference in color? I was planning on using a satin poly for sealant (mostly because it’s what is most convenient and what I’m accustomed to), but I’m interested in the dark wax after seeing this post. Any recommendations you have are much appreciated.
When you've selected your lumber, restack the pile neatly. Before heading off, calculate the number of board feet you have pulled just to be sure you have enough. It's advisable to allow for errors, waste and slight changes in plan when purchasing your material. Depending on the material and the complexity of the project I'll typically allow from 10 to 40% extra.
This is also a table made from a repurposed pallet. There’s not much you need to change about the pallet, except rearrange a few boards and make the frame smaller. The fact that each board has a slightly different color tone gives the table a special charm. The hairpin legs are a really nice touch. Check out the full tutorial to find out more about how you can build something similar for your own home.
×