Creativity knows no limits and this chicken coop coffee table proves it. It’s something that we found on findinghomefarms. It’s a one-of-a-kind piece with lots of character, the type of table that makes a statement no matter where you put it. Of course, such a daring and unusual project is not exactly very versatile so you’d need a certain type of decor to make it fit.
The sequence in which boards are cut from a log will determine how stable the boards will be once they dry. As a board loses moisture it will shrink in three dimensions. The change in length is so small as to be considered insignificant and the change in radial movement is always less than the tangential movement. This is most significant as the wood dries between the time it's cut (i.e. green wood), and the point where it is kiln dried or air dried and ready for use. Wood that shrinks excessively, or that has been dried improperly, will often develop checks at the ends. When shopping for lumber, carefully inspect the ends for any checking, or for excessively long checks. It is best to allow for some scrap at the end of each board, just in case. As you trim the end, hit the off-cut across the edge of your bench, and if it breaks in two, you'll have to cut off a little more.
Treeline offers only the finest wood carving tools and supplies. Everything from Treeline is backed by our 30-day guarantee against any defects. We have been providing wood carving tools since 1997 and we strive to excel in customer service and quality products. All employees at Treeline are very knowledgeable and professional, so if you are looking for the right woodcarving tools, contact us and we will do our best to help you.
We cut the decorative diagonal pieces to fit on this part. Mark each board with your pencil and cut them to fit exact. You can check out the video if you have questions about this part! We walk you through it. Cut the diagonal pieces to fit first, then mark and attach them to each other using wood glue and nails. Then, fit them in the box and attach them with wood glue and nails through the box and into each end of the X piece.
I love this & your videos. It’s really helped my confidence level (as a total beginner.) I’ve built your floating shelves (LOVE them) and the cake stand you did (I’m adding dowels in the middle for the connecting parts so I can take it apart & store it almost flat & not worry about Velcro) I’m wondering if you’d do a console that matches this? I really like Ana White’s x console but liked your legs better!
Teak is becoming rarer as the days go on, but it is the staple for fine outdoor furniture. Teak is highly weather-resistant and beautiful (not to mention expensive — can you believe almost $24 a board foot?). Teak has an oily feel and a golden-brown color. It rates a 3 on a scale of 1 to 5 for hardness and is only available from larger lumberyards and specialty suppliers.
It’s good to know that when it comes to choosing wood to buy that there are somethings that we need to take into consideration. I like how you mentioned that one thing we need to consider is whether we need it to be hard or soft for the project we are needing it for. This is something that we will have to look at and do more research on to make sure that we make the right decision.

The coffee table is most often the furniture piece which sits at the very heart of spaces such as the living room, outdoor lounge or pretty much any sitting area no matter the size or style. In these conditions, the coffee table is a focal point for that space and takes on a very special role. It’s often the piece which ties together the whole decor around it. There are, naturally, lots of possible designs and looks for such an element so we’ve prepared a set of inspiring coffee table plans which you might find useful if you’re ever interested in building your own furniture.
I’d like to add some type of sharpening system to your list. A simple sandpaper and slab system, stones, or the more expensive slow grinder system. Although listed, files should be in this sharpening/maintenance category as well. You’ll need these as soon as you purchase a majority of hand tools. They’ll be needed throughout each day of using the tools. Initial setup and routine maintenance will give better results with less fighting the grain and tool. Whether your a beginner or a master, the tools must be sharp and maintained.
Advanced residential carpenter classes focus on teaching students techniques in planning, measuring, installing fixtures and reading blueprints. Students learn about distance measurement and leveling and also review the equipment and tools used in site layout. Other advanced topics covered are exterior wall components and systems, insulation and applied building codes. Students in advanced carpentry classes also review how to read the symbols and abbreviations used on residential blueprints and practice job estimating, sustainable building practices and energy efficiency techniques.
There are three very important elements that must come together in making a project that will not only be pleasing to the eye, but will stand the test of time: good design, careful workmanship and meticulous selection of materials. You can continue to refine your design on paper, but at some point you will have to make that transition from a two dimensional drawing to selecting the lumber to use for each part. This can be one of the most difficult phases of any project and one that has the greatest effect on the final appearance of your finished piece.
Like with most live-edge tables, the hardest part of this project shared on instructables is finding the right slab of wood. It has to have a suitable shape and size for a coffee table top and to look interesting. Cracks, knots and other imperfections help to give it character. Once you have the slab, clean it and apply a protective finish, after which install the legs.

I love this & your videos. It’s really helped my confidence level (as a total beginner.) I’ve built your floating shelves (LOVE them) and the cake stand you did (I’m adding dowels in the middle for the connecting parts so I can take it apart & store it almost flat & not worry about Velcro) I’m wondering if you’d do a console that matches this? I really like Ana White’s x console but liked your legs better!
I needed a new coffee table for the living room and this design fit the bill perfectly. I came across a table from Ana-White.com that I loved, but modified it a bit because I wanted a breadboard style top. To see her plans click here. The difference between the table in this post is that I cut the top pieces to 41″ (vs 52″) and added the 2×6 pieces to each end, making it come to 52″ with a breadboard style top.

Somehow I overlook #1, the jointer and thickness planer, and I saw all the other tools and immediately thought that this was my first set of tools I bought when I started working as a carpenter on a friend’s crew. Then I saw my oversight and just couldn’t get over how incongrous those two items were to the rest of the list. Had I seen a scrub plane and a jack plane I would have more harmony in the list.
The campaign features a new customer-focused website, new advertising centered on visually-appealing wood applications, and the launch of Northwest Hardwoods’ Pinterest and Instagram accounts to convey visual ideas and aspirations for the many uses of hardwoods. The campaign offers an opportunity for Northwest Hardwoods to reach out to new audiences including designers, specifiers, architects and OEMs, underscoring the fact that no other building and design material is as visually appealing and as sustainable as timber. Additionally, the campaign includes the creation of product specific communications outreach that will support the company’s sales objectives.

A carpenter is someone who builds and repairs residential, commercial, or industrial structures. These structures can range from homes to commercial buildings to roads and can include individual components such as cabinets, staircases, doorframes, building foundations, and much more. And, although you may think that this occupation only requires physical strength and basic technical skills, carpentry actually requires a strong foundation of specialized expertise and experience in order to ensure that all jobs are completed in accordance with local, state, and national building codes.


Thanks so much with your patience with the site this morning.  We are growing (it's a good thing!) and are due for a server upgrade, but ALWAYS know keeping the site up and running fast is super important to me, and we are working very hard to improve the user experience of this site.  What can I say?  I APPRECIATE you each and every time you visit, and want to make sure each time you visit is pleasant for you.  Thank you!
So, just like the lumberyard map, email your entries to me at [email protected], and to help sort through, put “Vacation Spot” in the subject line. It could be a Shaker village with outstanding furniture, the Giant Sequoias of Northern California or a quirky out-of-the-way museum or shop. This will be put up for public consumption just like the above map – I want everyone to find their lumber and see great woodworking.
Description: Every woodturner enjoys the opportunity to give handmade ornaments to friends and family during the holidays, especially one that is made purely out of wood. No pre-made ornament kits or ornament hardware will be used in this class. One might call it au naturel!!!! During this class you will be given the opportunity to see various ornaments that have been turned on the lathe, ranging from small and simple to large and more decorative. Class objectives include, but are not limited to, the following: Wood choice (more common ornament wood species and pros and cons of each) Discussion and demonstration on how ornaments can be colored using a variety of markers, paints, dyes, and gilder's paste. Discuss and demonstrate how a variety of gouges and tools can be used to make ornaments, including texturing tools. Sharpening techniques - the instructor will assist all students when sharpening tools Ornament rough sketch and design, before the wood is on the lathe. Most important, every student in class will be given the opportunity to turn at least one ornament of their own. The instructor will assist with basic sketch and design, and will rotate among all students to assist with cuts, tool use, technique, sharpening, and helpful hints. Experience level: Beginner (some turning experience highly preferred) Suggested tools: Turning tools will be supplied; however, students are encourage to bring their own tools if they have them. 3/8" or 1/2" spindle gouge, narrow parting tool, and small roughing gouge is a great start. Students who wish to bring their own chuck may do so as well (1"-8 tpi, 2" or 50mm dovetail jaws, and pin jaws). Lunch break from 12:00 to 12:45
I’d like to add some type of sharpening system to your list. A simple sandpaper and slab system, stones, or the more expensive slow grinder system. Although listed, files should be in this sharpening/maintenance category as well. You’ll need these as soon as you purchase a majority of hand tools. They’ll be needed throughout each day of using the tools. Initial setup and routine maintenance will give better results with less fighting the grain and tool. Whether your a beginner or a master, the tools must be sharp and maintained.
Aside from pallets, lots of other things can also be repurposed into components for a DIY coffee table. For example, this one has a tile top. The frame is made of wood and can be crafted in no time. In fact, you can use some leftover wood pieces and if you also have an extra tile from previous renovations this can prove to be a cheap coffee table which you can build with things you already own.

I think it depends on the type of woodworker you would like to become. Are you more interested in traditional “electric free” carpentry or are you drawn to the ease and convenience of modern machinery? Also, I think you should take into consideration what kind and how much shop space you have available. I have worked with all the modern machines for years now, and are just presently finding personal satisfaction in traditional woodworking. In fact, last night I built my very first bookcase with just a few “powerless” hand tools. So in all, I would suggest some personal reflection…What type of woodworker do you want to become?…and from there garnish your shop appropriately.
In the end, do not forget the decorating aspect. As any table in your home, your perfect coffee table deserves the right centerpiece that will embellish and accentuate its beauty.Choose from a wide variety of designs. We also recommend you to try a diy centerpiece project to complete the design such a beautiful DIY wine bottle centerpiece. Find a lovely collection of such projects below and learn how to cut glass in a very easy step by step tutorial.
We really like the distressed look on this coffee table. There are a few ways in which you can achieve that. You can use reclaimed wood or you can create the antiqued finish artificially using special techniques. You can analyze the plans and the instructions shared on instructables to find out more about this strategy. They also show you how to build this stylish pinstripe table.
Description: Every woodturner enjoys the opportunity to give handmade ornaments to friends and family during the holidays, especially one that is made purely out of wood. No pre-made ornament kits or ornament hardware will be used in this class. One might call it au naturel!!!! During this class you will be given the opportunity to see various ornaments that have been turned on the lathe, ranging from small and simple to large and more decorative. Class objectives include, but are not limited to, the following: Wood choice (more common ornament wood species and pros and cons of each) Discussion and demonstration on how ornaments can be colored using a variety of markers, paints, dyes, and gilder's paste. Discuss and demonstrate how a variety of gouges and tools can be used to make ornaments, including texturing tools. Sharpening techniques - the instructor will assist all students when sharpening tools Ornament rough sketch and design, before the wood is on the lathe. Most important, every student in class will be given the opportunity to turn at least one ornament of their own. The instructor will assist with basic sketch and design, and will rotate among all students to assist with cuts, tool use, technique, sharpening, and helpful hints. Experience level: Beginner (some turning experience highly preferred) Suggested tools: Turning tools will be supplied; however, students are encourage to bring their own tools if they have them. 3/8" or 1/2" spindle gouge, narrow parting tool, and small roughing gouge is a great start. Students who wish to bring their own chuck may do so as well (1"-8 tpi, 2" or 50mm dovetail jaws, and pin jaws). Lunch break from 12:00 to 12:45
I consider this my “basic” tool list. Although I do not have a dedicated box for these tools, I assure you that they have a great home in cabinets, on shelves, and laying around on benches. When I do need to take my hand tools somewhere, the larger tools end up in a simple tongue and grooved latch box my grandfather owned. The smaller tools are always in my overall pockets. Overalls work great. They have multiple pockets, they’re comfortable, and they protect your upper body and legs. You only have to deal with small chunks of wood getting into the pockets, which can be dealt with if you or your other half are crafty enough to sew some flaps. It doesn’t bother me though. Thanks for your time.

Once the vinegar solution dries (or if you decided not to do the solution) you can go ahead and stain the project. First use a rag or air compressor to remove any dust from the table. Then use a clean rag to apply the stain of your choice. Don't forget to wear gloves and ventilate the area. Have a brush in your other hand to stain hard to reach areas.
You don’t have to build the coffee table from scratch if you can use an already existing one and simply give it a makeover, maybe add a new feature to its design. A great example is this Ikea Lack table which got a beautiful built-in planter at the center. It’s a transformation which you can do too. Check out our video tutorial for details and instructions.
There are numerous coffee table woodworking projects in the market. In case you are willing to design a coffee table for your den, living room or family room, there are some amazing coffee table woodworking projects to keep in mind. One can choose different types of such designs, which add to the beauty, look and design of a room. Mostly people prefer the designs that are eye catchy as well as unique. So let’s dig in to check out some really amazing coffee table woodworking projects.

Carpenters craft structures and products from wood, steel, fiberglass and other materials. There are different types of carpenters, including residential, industrial and commercial carpenters. Residential carpenters may build new homes or do remodeling work, building structures like walls, stairways, floors, roofs and decks. Commercial carpenters, who may construct schools, malls and hospitals, use many of the same skills, but they may work more with concrete and steel. Industrial carpenters build infrastructure like tunnels, sewers and dams.

First, build two boxes for each leg assembly. These are attached using wood glue and 2.5” pocket hole screws through the horizontal boards and into the vertical boards.  You want your pocket holes facing the outside of the box on this part because we will cover them with another board on the next part.  We used our K5 Kreg Jig for this part.  We get asked ALL the time which Kreg Jig to start with.  We always suggest the K5.  We use it on almost every build.  You can find it HERE on Amazon!
Delta 22-590 13 in. portable thickness planer includes: Delta 22-590 13 in. portable thickness planer includes: 3 cutting knives cutter head wrench dust chute with 4 in. port and magnetic blade changing tool. High-speed steel indexed double-sided knives provides 2X blade life and allows for quick blade changes. Oversized cutter head height adjustment handle with indexing ring provides ...  More + Product Details Close
Dan, my work space that is available for power tools is quite small, about 6′ x 20′. It may seem like a lot on the surface, but a long rectangle is a bear to work in. It requires a lot of serpentine action. That said, I don’t have too much room for large footprint tools. I have settled finally on three big tools; a small bench saw, a thickness planer, and a drill press. I had to forgo the jointer, so I use hand tools to make up for it’s absence (as I do with a lot of my hand tool techniques). I have gotten to the point where I can flatten one side and true an edge of a board reasonably quick. I then finish it up with the thickness planer and table saw, giving me a nice flat board. I guess what I am basically saying is, there’s more than one way to skin a cat, and don’t write off hand tools as a quaint way to experience the past. They worked for thousands of years, and still do! Thanks for the blogs, they make for great reading.
This project actually started with me wanting to build a chair for myself, however I lacked advanced woodworking tools and a workshop. I therefore began making furniture that was as straightforward as possible and could be build easily with simple tools. Most importantly, all parts could be cut at the DIY store where I got my plywood. This meant I didn't need a saw bench or lots of space. The cut parts were easy to transport to my home and I could pretty much build the whole chair on the kitchen table. This inspired me to make other furniture pieces in similar fashion.
×