11-2. Pipe clamps, I have about 10 of them with varying lengths of black pipe in 1′ increments. I can switch out the clamps for larger lengths on larger projects, or downsize as needed. (very rarely do I need more than 6 clamps on a project during drying time, and when I do, it’s time for a cup of coffee and a 1/2 hour break while I wait) You keep your initial investment down, and buy them as you need them to increase your collection.
There are often situations when the original message asks for opinions: "What is the best widget for my type of shop?". To a certain extent, the person posting the message is responsible for including specific questions within the message. An open ended question (like the one above) invites responses that may read as sales pitches. WOODWEB suggests that companies responding to such a question provide detailed and substantive replies rather than responses that read as a one-sided product promotion. It has been WOODWEB's experience that substantive responses are held in higher regard by our readers (return to top).
I have used a Workmate successfully for years and I am in the process of building an upgraded replacement for the work surfaces. My replacement bench top will be a little longer, much thicker and it will have and extended apron between the two halves to greatly improve holding wood vertically for dovetailing. With this simple upgrade it turns the little Workmate into a very capable portable woodworking bench.

If desired, add decorative trim pieces to your coffee table. We used an x pattern, but you can leave it as-is if desired. Simply dry fit your pattern into the side panels of your coffee table. Then attach using wood glue and brad nails. After your pieces have been added, fill any holes. Once your wood filler is dry, sand with 120 grit sandpaper. Then stain or paint and finish with a polyurethane.

The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.


To best engage with designers and architects, Northwest Hardwoods has expanded its social media reach to include Instagram and Pinterest. Both channels are visually based and aspirational, which will allow Northwest Hardwoods to showcase not only its many types of wood grades and species, but also the beautiful and varied applications for these woods – from cabinets to decking to furniture.
In general, you can expect to spend three to four years obtaining a combination of classroom and on-the-job training in order to become a carpenter. While you won't technically be considered a carpenter until reaching journeyworker status at the end of the training period, you will have the opportunity to pursue a paid position in the field for the duration of your training. Compared to the amount of time it takes to learn how to be an electrician, and training for some other trades, the length of time it takes to get journeyworker status as a carpenter is relatively reasonable.
I have used a Workmate successfully for years and I am in the process of building an upgraded replacement for the work surfaces. My replacement bench top will be a little longer, much thicker and it will have and extended apron between the two halves to greatly improve holding wood vertically for dovetailing. With this simple upgrade it turns the little Workmate into a very capable portable woodworking bench.
Once the mixture is made, simply brush the solution on the wood. It won't immediately turn colors, but over a few hours you'll notice a considerable difference. Check out the photos of my farm table project to see how well it worked using fir boards. You'll notice the fir 2×2's used in this project really took the solution well. The other boards had a little coloring and grain enhancement, but white pine doesn't have many tannins in it so it is less reactive.

There are often situations when the original message asks for opinions: "What is the best widget for my type of shop?". To a certain extent, the person posting the message is responsible for including specific questions within the message. An open ended question (like the one above) invites responses that may read as sales pitches. WOODWEB suggests that companies responding to such a question provide detailed and substantive replies rather than responses that read as a one-sided product promotion. It has been WOODWEB's experience that substantive responses are held in higher regard by our readers (return to top).


Even if you are using a beautiful (yet unstable) grain pattern on part of your furniture, it’s a good idea to use stable wood on the other parts. For example, look at an old wooden door. The panels usually have more decorative (less stable) wood, but the rails and stiles (parts of the frame) are usually very stable straight grained wood (don’t worry, I’ll clarify “straight grain” below).

About forty years ago I purchased a Shopsmith Mark V because I lacked space for a large shop, and also moved around the United States a lot. Later I purchased another Shopsmith Mark V Model 510 for the increase in table size and flexibility. I do wood working as a hobby, not to do many projects as fast as possible. I also have every tool and accessory that Shopsmith makes for the two primary tools. Their quality is excellent, and while I enjoy antique tools like the 1912 three phase electric Camel Back Drill Press I purchased for my son’s shop, the Shopsmith does every thing I have ever needed.

The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.
Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!
×