Thanks so much with your patience with the site this morning. We are growing (it's a good thing!) and are due for a server upgrade, but ALWAYS know keeping the site up and running fast is super important to me, and we are working very hard to improve the user experience of this site. What can I say? I APPRECIATE you each and every time you visit, and want to make sure each time you visit is pleasant for you. Thank you!
Dan, my work space that is available for power tools is quite small, about 6′ x 20′. It may seem like a lot on the surface, but a long rectangle is a bear to work in. It requires a lot of serpentine action. That said, I don’t have too much room for large footprint tools. I have settled finally on three big tools; a small bench saw, a thickness planer, and a drill press. I had to forgo the jointer, so I use hand tools to make up for it’s absence (as I do with a lot of my hand tool techniques). I have gotten to the point where I can flatten one side and true an edge of a board reasonably quick. I then finish it up with the thickness planer and table saw, giving me a nice flat board. I guess what I am basically saying is, there’s more than one way to skin a cat, and don’t write off hand tools as a quaint way to experience the past. They worked for thousands of years, and still do! Thanks for the blogs, they make for great reading.
I was telling my brother of the different ways I sharpen and he seemed interested in the slab/sandpaper method. When I went to get the extra supplies I picked up a slab of granite, adhesive, and sandpaper for sharpening. When the job was completed, the saw, the can of finish, and the slab with sandpaper were gifted to my brother. I could have shortened my list a little,
Carpenters craft structures and products from wood, steel, fiberglass and other materials. There are different types of carpenters, including residential, industrial and commercial carpenters. Residential carpenters may build new homes or do remodeling work, building structures like walls, stairways, floors, roofs and decks. Commercial carpenters, who may construct schools, malls and hospitals, use many of the same skills, but they may work more with concrete and steel. Industrial carpenters build infrastructure like tunnels, sewers and dams.
Wow, what a great problem to have Boris! If you can send some photos I’ll look at them. But unseen, I’d ask them to try to get some quartersawn boards out, and also some full width flatsawn boards. It just depends on how much wood you’ll get if you quartersaw it. It also depends on what you think you’ll build down the road. Some furniture pieces don’t need to be quite as stable as others. Good luck!
It's generally more difficult to find long boards. Stock under four or five feet long can often be cut from longer boards, but as the parts become longer, the rough stock will have to be either very clear and straight, or have extra thickness to allow you to remove any bow along its length. In making parts for the room divider (featured in this issue), four stiles had to be set aside: three because they kept bowing no matter how often they were jointed flat, and one because it was under the minimum thickness by the time it was flat.
Screwdrivers are another must-have in the woodworker’s set of hand tools. Not only will you need Phillips and slot, or flathead screwdrivers, you’ll need star drivers and Torx drivers, too. A quality construction is vital to a good set of screwdrivers. So many of them are made out of soft metal, and the first time you put any “oomph” behind them, they strip out, becoming absolutely useless.
Disclaimer: Almost any DIY project involves risk of some sort. Your tools, materials, and skills will vary, as will the conditions at your project site. Rogue Engineer has made every effort to be complete and accurate in the instructions provided on this website. Rogue Engineer will not assume any responsibility or liability for damages or losses sustained or incurred in the course of your project or in the use of the item you create. Always follow the manufacturer's operating instructions in the use of tools, check and follow your local building codes, and observe all commonly accepted safety precautions.
I've found that it is easiest to attach the shelf by attaching the 2×2 side rails prior to connecting it to the table. To do this you'll sort of take a minor step back by removing the two lower 2×2 side rails (only 8 screws). Then drill the shelf to the 2×2's as shown below. Lift the shelf into place and attach each end of the shelf to the lower end rails using 2 1/2″ Kreg Screws. Once that is secure flip the table right side up and add the cross supports.