When I started planning this makeover, I knew I wanted to get rid of the glass coffee table I had and go with something more rustic and cozy… something with beautiful wood grain that looks like it’s been in an old farmhouse somewhere for ages. So rather than searching every single antique store in town or buying something off the shelf at a big box store, I gathered up my tools, picked up some lumber, and made myself a new coffee table!
Wow, what a great problem to have Boris! If you can send some photos I’ll look at them. But unseen, I’d ask them to try to get some quartersawn boards out, and also some full width flatsawn boards. It just depends on how much wood you’ll get if you quartersaw it. It also depends on what you think you’ll build down the road. Some furniture pieces don’t need to be quite as stable as others. Good luck!

While flipping through the boards, keep an eye open for signs that a number of boards may have come from the same tree. Looking at the ends and the growth rings will tell you where in the log the board was sawn. In some cases, knots may go through more than one board, and often the outer boards have a live edge. By comparing these features, the colouring, grain and other distinguishing marks, it is often possible to identify several boards cut from the same log.
Lots of good comments! I do think it is a bit of stretch to include a jointer and surface planner on the ‘basics’ list – we’ve got a slippery slope here! And a lot of different approaches – money, space, time, resources, etc. But lets plunge ahead. If you buy your wood already (or mostly) prep’ed, then the jointer & surface planner can be postponed. You definitely need a way to accurately measure linear distances (e.g. length, width) so a good ruler and tape measure. You need to be able to measure squareness – so you need a good combination square. You need to be able to mark the wood – so a good marking knife, an awl, some chalk, a fine pencil, etc. You should have some decent chisels (and good ones don’t need to cost a lot!). You will need to sharpen them (again not expensive – piece of plate glass and some sandpaper). You need a way to accurately cut your wood – a couple of good handsaws and a file or two for sharpening. You really should have a decent work surface/work bench/etc – a good first project by the way. Last of the basics – a good drill (3/8″ vs battery type). Lastly (I could go on but room is lacking), take a look at Paul Seller’s video’s for simple but highly competent work.
Another unusual item which you can repurpose when building a coffee table is a window. The plans featured on martysmusings are actually a bit more complex than that. This is not just a table with a window as a top. That top opens up and the space inside the frame can be used as a storage nook. It’s quite clever and you can do a lot of cool things based on this idea. For example, you could fill the interior with cute little plants or interesting-looking branches or you could create a terrarium which can be admired from above. sAlternatively, use it as a simple storage area for things you don’t ming keeping on display.
Your moisture meter should have settings on it that will account for different species of wood. For instance, oak is a hardwood, but ebony is an even harder density wood. If you are planning an inlay job using both types of wood, you will need to know the moisture content levels of each of the two species so that your inlay glue joints will stay intact. These different wood species have different specific gravities, which must be used or programmed into the moisture meter.

Woodworking is an ancient art that requires an artistic eye and precise tools. Whether you're starting off in woodworking or you're an established woodworker, you need good woodworking machinery to help you create your art. A good knowledge of the major machines and how they help you when working with wood can go a mile in making the woodworker’s job easier.

This is the side table version of the stylish project we shared previously. In certain configurations, it could function as a coffee table. It’s a design suitable for small spaces. The wooden top has this hollow storage compartment which is great for keeping things like a book, a magazine, the remote control or the phone when relaxing on the sofa. The hairpin legs give the table a slender look.

Online carpentry education opportunities may be offered as certificate programs or as career diplomas. In programs like these, you'll practice basic carpentry in addition to studying building codes, blueprint reading, math and business management. The courses will typically cover roofing, wall paneling, wood-joining techniques and materials estimation, among other topics. You'll also learn how to use hand and power tools. Depending on the program, you might even take a Spanish course.
Products and systems by Lamello have always been Products and systems by Lamello have always been designed for longevity and reliability. This legendary durability is combined with environmental stewardship in view as strict environmental regulations at our production site in Switzerland ensure that all resources are used with consideration many of them stemming from sustainable husbandry and management. ...  More + Product Details Close
In this step take your 2×2 rails that are 41″ long and drill  2 pocket holes on each end using a Kreg Jig. Then take 2 1/2 kreg screws and attach the side rails to each 2×4 end piece. Measure 2 1/4 inches up from the bottom to hang your lower 2×2 rail. Note that in the photo my pocket hole screws are pointing inward. The top rail's pocket holes can face inside the table or to the ground. No matter what they won't be seen. Make sure to have the lower rail's pocket holes facing the floor so you'll be able to attach the shelf to them later.
Some moisture meters have pins that penetrate the surface of the wood. This can leave tiny holes that mar the surface and require filling. Others are pin-less. They have sensing plates that scan the wood beneath. However, not all pinless moisture meters are the same – look for one that uses technology that is not affected by the surface moisture in the wood, such as Wagner Meters IntelliSense™ Technology Moisture Meters.
Description: This workshop is designed for those who have recently gotten a wood lathe, or have had one for a while, and haven't gotten around to using it until now. During this workshop students get acquainted with the wood lathe and its parts and accessories. We will cover the turning process, as well as sanding and applying finish to a project while it's on the lathe. Students will also be shown a variety of turning tools and how they function. You will also be introduced to wood selection, tool selection, and tool sharpening. Students will test their skills while working on a small turning project. Students should bring suitable eye protection such as safety glasses, goggles, or a face shield. If you have problems with wood dust, a respirator or dust mask would be advisable. Also bring any wood turning tools you might have. Tools and safety gear will be provided for those who don't own them. Materials for turning will be provided.
In this step take your 2×2 rails that are 41″ long and drill  2 pocket holes on each end using a Kreg Jig. Then take 2 1/2 kreg screws and attach the side rails to each 2×4 end piece. Measure 2 1/4 inches up from the bottom to hang your lower 2×2 rail. Note that in the photo my pocket hole screws are pointing inward. The top rail's pocket holes can face inside the table or to the ground. No matter what they won't be seen. Make sure to have the lower rail's pocket holes facing the floor so you'll be able to attach the shelf to them later.
Apply glue to the ends of the 1 x 2 End Pieces for the Base and Apron, and then clamp them in place against the inside of the Leg. Position the pieces so that one runs flush with the top edge, and the other sets below the line marked in Step 7. Center both pieces on the leg, and tilt them so that they run parallel to the edge of the Leg. Using a drill/driver and 1¼-inch pocket holes screws, attach the pieces to the Leg. Repeat on the opposite end. 

Thanks for the feedback. We’re glad you found the list helpful. Please note that this page contains only 10 of the 40 top tools for woodworking, displaying only hand tools. You can find the next 10 here: https://www.wagnermeters.com/top-40-woodworking-tools-2/. There are links at the bottom of each article to the next group of tools so you can view the entire list. Hope this helps.
Just a little nitpick on the tape measure blurb. The hook should not be completely tight. It should move in and out about a 1/16th or the thickness of the hook. This way you get an accurate measurement whether you hook a part to measure or bump up to it. If you want more accurate measurements with a tape measure, “burn” an inch instead of hooking or bumping the part. Just line up what you want to measure with the 1″ mark and subtract that inch from the final measurement.
When I started planning this makeover, I knew I wanted to get rid of the glass coffee table I had and go with something more rustic and cozy… something with beautiful wood grain that looks like it’s been in an old farmhouse somewhere for ages. So rather than searching every single antique store in town or buying something off the shelf at a big box store, I gathered up my tools, picked up some lumber, and made myself a new coffee table!

Whether you are a beginner or a DIY professional, if you have a love for the craft of woodworking The Home Depot has got you covered. We have all the essential tools for woodworking that let you hone your craft. Our huge selection of drill presses and miter saws will put the power in your hands to complete your projects faster and easier. And whether you are looking for the strength of a powerful router or the versatility of a lathe, you can find everything you need to help with projects, large and small. If your carpentry plans also include building materials, you don't need to look any further than The Home Depot. From wood and lumber to decking and fencing materials, it's all right here.
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.
After they get empty, we remain no longer concerned with those wooden barrels! If you are having some long-forgotten wooden barrels they time to plan them for restoring living room fashion points! Here is way to convert an old barrel into a stunning coffee table that will also provide a secrete stash as you can see here! Perfect gift for rustic-modern lovers! Here is how to make it artofmanliness
After you learn the basics from this video and article I encourage you to look at the bottom of this article for a list of links, books, and DVDs that will expand your understanding beyond the scope of this article. But this book is the best resource I have found so far: “Understanding Wood: A Craftsman’s Guide to Wood Technology” by R. Bruce Hoadley.
In the sixty years of woodworking I have found two tools of increasing necessity. One is a band saw. I can do most of my work with a band saw and hand plane. The second tool is a bow saw, or actually several bow saws. They will replace the band saw if required, though they are slow. One I made about twenty years ago has a one and a half inch wide rip blade and is about thirty inches long. I think the blade is from an old industrial band saw blade I picked up and sharpened into a rip saw blade. It works very well on ripping lumber, logs, etc. Though it tires me out to much to use it now.
Most carpenter classes and courses lead to a certificate or associate's degree. Graduates can work in many different specialty areas including residential and commercial carpentry. According to the U.S. Bureau of Labor Statistics, 1 in 3 carpenters are self-employed, so some courses include basic business skills for carpenters like cost estimating and project planning. Primarily, however, students will learn about tools, materials and building techniques.
To us it is clear: Power, passion and conviction in the process of creation is what drives us and makes us so successful. The common objective is this, both today and for the future, to build the best woodworking machines with respect for our customers and for our environment. This is reinforced with each machine that leaves our factory in Hall in Tirol.
The campaign features a new customer-focused website, new advertising centered on visually-appealing wood applications, and the launch of Northwest Hardwoods’ Pinterest and Instagram accounts to convey visual ideas and aspirations for the many uses of hardwoods. The campaign offers an opportunity for Northwest Hardwoods to reach out to new audiences including designers, specifiers, architects and OEMs, underscoring the fact that no other building and design material is as visually appealing and as sustainable as timber. Additionally, the campaign includes the creation of product specific communications outreach that will support the company’s sales objectives.
At Able Skills we pride ourselves in the diversity of the skills that are available within our carpentry training centre. If upon completion of this course you would like to learn much more then you can consider upgrading to City & Guilds Certificate & Training to NVQ Level 2. This would require you to train for an additional 5 weeks; payment would be adjusted to reflect what you have already paid on this course.
Thread Related Link and Image Guidelines Thread Related Links posted at WOODWEB's Forums and Exchanges should point to locations that provide supporting information for the topic being discussed in the current message thread. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related Link that directs visitors to an area with inappropriate content will be removed. WOODWEB reserves the right to delete any messages with links or images it deems inappropriate. (return to form)
We are all well aware of the role of a DIY coffee table for a living room which is highly versatile! It is what you need to get first while entertaining some visitors or guests in the living room! The conversations are also to start always by sitting around it! It is seen mostly in the center of the sitting plans! The reason is that all the sitting personages can use it to place their mobile phones, cups, beverage mugs, magazines and other materials over it while they need to get their hands free for the detailed conversations! So this all tells that how utilitarian item a coffee is!
A key part of my kit is the shopping list. After I have worked out the design of a project, I create an inventory of the parts, using Cutlist Plus software. The rest of the kit consists of: a pencil, some white chalk, a pad of graph paper on a clipboard, a calculator, and a moisture meter. I also have a small digital recorder I take along with me, which I use to record special notes or reminders.

I’m currently working on a dining room table with this color in mind (I also plan on a coffee table soon). I’ve been testing out stain colors and dark walnut is currently in the lead. I love the way this coffee table turned out in color. How many coats of stain did you use? Also, did the dark wax make a big difference in color? I was planning on using a satin poly for sealant (mostly because it’s what is most convenient and what I’m accustomed to), but I’m interested in the dark wax after seeing this post. Any recommendations you have are much appreciated.
This is also a table made from a repurposed pallet. There’s not much you need to change about the pallet, except rearrange a few boards and make the frame smaller. The fact that each board has a slightly different color tone gives the table a special charm. The hairpin legs are a really nice touch. Check out the full tutorial to find out more about how you can build something similar for your own home.

I built my coffee table!! I used the plans at www. EasyWoodwork.org to build mine – highly recommended you check those out too. They are detailed and super easy to read and understand unlike several others I found online. The amount of plans there is mind-boggling… there’s like 16,000 plans or something like that for tons of different projects. Definitely enough to keep me busy with projects for many more years to come haha

×