Not all species are available in quarter sawn form from all dealers, but it can be possible to cut parts from wider boards to accomplish the same end. At the lumberyard I will often look for wider planks for this very reason. When a wide board is cut from the log it will have some vertical grain on the outer edges and some face grain in the center of the board. By purchasing enough stock and carefully laying out the parts it would be possible to use quarter sawn material for all visible parts. Decisions like this must often be made at the lumberyard based on the stock on hand. It is a way to stretch your material budget a little further, by buying a lower grade and resawing it for appearance back in the shop.
Residential carpenters specialize in building and remodeling family homes, townhomes, and condominiums. As part of a single job, they might create and set forms for footings, walls, and slabs, and frame and finish exterior walls, roofs, and decks. Additionally, residential carpenters frame interior walls, build stairs, and install drywall, crown molding, doors, and cabinets. They may also tile floors and lay wood floors and carpet.

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!


Using wood glue and 1 1/4" pocket hole screws, attach the frame you just built (19" x 11") to the 4x4 frame posts. You will use the pocket holes you drilled in the 19" boards. The frame will sit on the edge of the grooves, not inside. See plans for details. The frame should sit flush with the tops of your 4x4's. This will make the bottom 4" off the ground.
Let’s start with perhaps the most basic tool in every household – the claw hammer. The claw on one side of the head should be well counterbalanced by the finished head, which should be somewhat rounded. The other kind of head is the waffle-head. Most commonly used in construction, it leaves a distinctive waffle mark on the wood when you drive the nail. This, of course, is not the proper nail for woodworking.
Put an emphasis on the material used in the design of the coffee table. For example, if you’re using wood, showcase its natural beauty, with knots, cracks and all other imperfections. A live edge top would definitely be a good choice in such a case. Check out these rustic coffee table plans to find out all about the steps leading up to a gorgeous and yet simple design.
A career in this field may require you to meet certain licensing, training, and other requirements that can vary by vocation and state. You should check with your state, local government, and/or licensing board to find out which requirements may be applicable in your state. Click here for contact information on state licensing/regulatory boards and certain professional licensing information.
Sears Trostel is the source for the highest quality lumber, custom millwork, specialty wood products, FSC® certified products and tool brands. Serving commercial and retail customers throughout Colorado and Rocky Mountain communities since 1929, our 10,000-piece moulding and interior trim library, super-fast Lean Manufacturing processes, and huge inventory of products and services are unmatched in the region. 
Once the vinegar solution dries (or if you decided not to do the solution) you can go ahead and stain the project. First use a rag or air compressor to remove any dust from the table. Then use a clean rag to apply the stain of your choice. Don't forget to wear gloves and ventilate the area. Have a brush in your other hand to stain hard to reach areas.
I’ve gained a lot more confidence in my woodworking capabilities over the last year, so I wanted to tackle this project solo (a.k.a. without the assistance or supervision of Jeremy), and I was actually really surprised at how easy and fast this table came together. I was able to shop for my supplies, make my cuts, and build the table all within just a few hours. Not bad for a little afternoon project!
Problems donating? | Other ways to give | Frequently asked questions | We never sell your information. By submitting, you are agreeing to our donor privacy policy. The Wikimedia Foundation is a nonprofit, tax-exempt organization. If you make a recurring donation, you will be debited by the Wikimedia Foundation until you notify us to stop. We'll send you an email receipt for each payment, which will include a link to easy cancellation instructions.
I have used a Workmate successfully for years and I am in the process of building an upgraded replacement for the work surfaces. My replacement bench top will be a little longer, much thicker and it will have and extended apron between the two halves to greatly improve holding wood vertically for dovetailing. With this simple upgrade it turns the little Workmate into a very capable portable woodworking bench.
×