I just moved overseas and had to give up all of my power tools due to space limitations and power incompatibility. Upon arrival the first power tool that I bought was a cordless drill/driver and the second was a circular saw. I then modified the saw to improve its performance for cabinet quality work by putting a zero clearance baseplate (just a piece of 1/4″ plywood screwed to the base) this allows the saw to cut plywood panels without tearing up the edges. I also bought a length of aluminum rectangle tube stock for a straight edge. Together the straight edge and the zero clearance baseplate makes the circular saw a fairly accurate tool for plywood construction projects. It’s not as easy to use as a Festool track saw but it cuts almost as clean and cost about 1/5th the price.
My $0.02 worth. I agree with the thickness planer [mine is 10″] but anything over a 6″ jointer is expensive and space-consuming, so use hand planes as in your later blog. I inherited an 8″ table saw that my dad and I used to build a 12′ outboard boat back in 1955. I’ve used it for ripping, but I’m having second thoughts because of safety issues. Some have suggested a band saw for ripping, which is quieter and safer to use. I gave my router away [and hope to get rid of my Freud biscuit joiner and 6″ jointer]. A quality eggbeater drill works every bit [pun not intended] as well as a power drill, and they cost less. A coping saw and a jewelers saw negate the need for a jigsaw unless you are into making puzzles. Chris Schwarz has a video short on one of the Highland Woodworker series showing how to joint the edge of a board with a plane and a simple jig on the workbench surface. Another reason to bypass the jointer.
Description: Every woodturner enjoys the opportunity to give handmade ornaments to friends and family during the holidays, especially one that is made purely out of wood. No pre-made ornament kits or ornament hardware will be used in this class. One might call it au naturel!!!! During this class you will be given the opportunity to see various ornaments that have been turned on the lathe, ranging from small and simple to large and more decorative. Class objectives include, but are not limited to, the following: Wood choice (more common ornament wood species and pros and cons of each) Discussion and demonstration on how ornaments can be colored using a variety of markers, paints, dyes, and gilder's paste. Discuss and demonstrate how a variety of gouges and tools can be used to make ornaments, including texturing tools. Sharpening techniques - the instructor will assist all students when sharpening tools Ornament rough sketch and design, before the wood is on the lathe. Most important, every student in class will be given the opportunity to turn at least one ornament of their own. The instructor will assist with basic sketch and design, and will rotate among all students to assist with cuts, tool use, technique, sharpening, and helpful hints. Experience level: Beginner (some turning experience highly preferred) Suggested tools: Turning tools will be supplied; however, students are encourage to bring their own tools if they have them. 3/8" or 1/2" spindle gouge, narrow parting tool, and small roughing gouge is a great start. Students who wish to bring their own chuck may do so as well (1"-8 tpi, 2" or 50mm dovetail jaws, and pin jaws). Lunch break from 12:00 to 12:45
The article is coming soon to the magazine, and I’m happy to say that the map is here. Months ago, I put out a call over social media for readers to submit their favorite local lumberyards, with a short review or blurb about what they like about their yard – I called it “The Great Lumberyard Census.” After hours of sorting through the entries, formatting them for the digital interactive map and playing with GIS software, the map and accompanying directory is finished.
Furniture Making engages students in the process of furniture making. Topics include an American historical overview and a look at the use of power and hand tools. Common themes include sketchbook work, cutting, hand tools, power tools, bending and jig making. This course employs various technical readings, visual aids, videos, project pictures and assignments.
The Amish here in Ohio use a nifty wooden rule for calculating bd. ft. It has a brass football shaped hook on the end and they’re about 2′ long. Three columns of numbers run down the length of stick. These columns are the length of stock say, 12,14,16 foot. Within these columns, bd. ft. has already been calculated and marked. For a 16′ bd. the hook is placed over one edge and a reading of bd. ft. is taken from opposite edge from the 16′ column. “Audels Carpenters and Builders Guide #1” pg. 146, shows a good example. They call… Read more »
Most chisels are beveled on the 2 sides and on the cutting edge, but specialty chisels may only be beveled at the cutting edge. This bevel will be at 20 to 25 degrees down the length of the blade on one side, and flat on the backside. The blade will be between 4” and 7” long. Make sure you get chisels with a grip that fits your hand. If the grip is too small, you won’t be able to hold the chisel steady as you work. Be sure to use a mallet or wood hammer when you work, so that you don’t destroy the head on your chisel. Keep track of the edge caps, keep them sharp, and oil the metal now and then after you’ve used them, and they should be good for years. If you don’t have the edge caps, get a roll to keep them in. This will prevent them from bouncing around in your tool box drawers and getting damaged.
The owners, webmasters, administrators, authors and editors, expressly disclaim all and any liability to any person, whether a user of this website or not, in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance, whether whole or partial, upon the whole or any part of the contents of this website. Please exercise caution when working with any tools or machinery. Follow common safety rules and precautions as outlined in any manuals related to the equipment being used. If advice or other expert assistance is required, the services of a competent professional person should be sought.
Once the vinegar solution dries (or if you decided not to do the solution) you can go ahead and stain the project. First use a rag or air compressor to remove any dust from the table. Then use a clean rag to apply the stain of your choice. Don't forget to wear gloves and ventilate the area. Have a brush in your other hand to stain hard to reach areas.
Lots of good comments! I do think it is a bit of stretch to include a jointer and surface planner on the ‘basics’ list – we’ve got a slippery slope here! And a lot of different approaches – money, space, time, resources, etc. But lets plunge ahead. If you buy your wood already (or mostly) prep’ed, then the jointer & surface planner can be postponed. You definitely need a way to accurately measure linear distances (e.g. length, width) so a good ruler and tape measure. You need to be able to measure squareness – so you need a good combination square. You need to be able to mark the wood – so a good marking knife, an awl, some chalk, a fine pencil, etc. You should have some decent chisels (and good ones don’t need to cost a lot!). You will need to sharpen them (again not expensive – piece of plate glass and some sandpaper). You need a way to accurately cut your wood – a couple of good handsaws and a file or two for sharpening. You really should have a decent work surface/work bench/etc – a good first project by the way. Last of the basics – a good drill (3/8″ vs battery type). Lastly (I could go on but room is lacking), take a look at Paul Seller’s video’s for simple but highly competent work.
Most carpenter classes and courses lead to a certificate or associate's degree. Graduates can work in many different specialty areas including residential and commercial carpentry. According to the U.S. Bureau of Labor Statistics, 1 in 3 carpenters are self-employed, so some courses include basic business skills for carpenters like cost estimating and project planning. Primarily, however, students will learn about tools, materials and building techniques.
A career in this field may require you to meet certain licensing, training, and other requirements that can vary by vocation and state. You should check with your state, local government, and/or licensing board to find out which requirements may be applicable in your state. Click here for contact information on state licensing/regulatory boards and certain professional licensing information.
Rustic furniture look is the hottest furniture look that is chosen to score high value styles and living room fashion trends! So why not get some style-worthy living room coffee table out of some old wood logs? Follow the construction steps and pattern here to get a fab like shown one for good reputation of your living room! Here is the tutorial bhg
Your moisture meter should have settings on it that will account for different species of wood. For instance, oak is a hardwood, but ebony is an even harder density wood. If you are planning an inlay job using both types of wood, you will need to know the moisture content levels of each of the two species so that your inlay glue joints will stay intact. These different wood species have different specific gravities, which must be used or programmed into the moisture meter.
2 small Japanese pull saws, a western push saw, fret saw, set of chisels, bit brace with a roll of arbor bits, rabbet plane, side rabbet (trim) plane, 2 shoulder planes, 3 set of diamond stones, slip stone, multiple files, a rasp or two, 2 small bar clamps, a mini vise, hand scrapers, scratch beader with cutters, combination plane with cutters, smoothing plane, jack plane, block plane, combination square, steel straight rule, 12′ tape measure, small bottle of glue, a few short dowels, 2 marking gauges, and a few different marking instruments (awl, pencils, marking knife).
We are all well aware of the role of a DIY coffee table for a living room which is highly versatile! It is what you need to get first while entertaining some visitors or guests in the living room! The conversations are also to start always by sitting around it! It is seen mostly in the center of the sitting plans! The reason is that all the sitting personages can use it to place their mobile phones, cups, beverage mugs, magazines and other materials over it while they need to get their hands free for the detailed conversations! So this all tells that how utilitarian item a coffee is!
The campaign features a new customer-focused website, new advertising centered on visually-appealing wood applications, and the launch of Northwest Hardwoods’ Pinterest and Instagram accounts to convey visual ideas and aspirations for the many uses of hardwoods. The campaign offers an opportunity for Northwest Hardwoods to reach out to new audiences including designers, specifiers, architects and OEMs, underscoring the fact that no other building and design material is as visually appealing and as sustainable as timber. Additionally, the campaign includes the creation of product specific communications outreach that will support the company’s sales objectives.
Hey Great Article,Thanks. 4 months ago, I started looking for woodworking.The industry is extremely interesting,but I have problems with how I can do it.My uncle who has been doing more than me in this industry,has suggested to me to follow Teds plans.Do you think it’s a good move to follow these plans??I keep reading good reviews about Teds plans but I am unsure if it will still work on me.At this time I can purchase these plans at a very low price,so if possible can you leave me feedback on wether I should do it or not. It would mean a lot coming from an expert in this field.
The beverage pallet coffee table is one of the most significant choices for your living room if you live to entertain. It comprises a built-in space for the bucket of the ice storage that possibly keeps your drinks fresh and cold, space which can be tucked away and be covered up when necessary. In this case beverage pallet coffee table is best for you.
At Able Skills we pride ourselves in the diversity of the skills that are available within our carpentry training centre. If upon completion of this course you would like to learn much more then you can consider upgrading to City & Guilds Certificate & Training to NVQ Level 2. This would require you to train for an additional 5 weeks; payment would be adjusted to reflect what you have already paid on this course.
Ashworth College is unlike any other carpentry school online. Our Carpentry training focuses on the real-world tools, knowledge, and procedures used by construction professionals on residential and commercial building projects. Studying online in a way that fits your busy life, you’ll graduate with the carpentry skills employers demand, helping you focus on practical skills and turn your woodworking hobby into a true profession.
There are three very important elements that must come together in making a project that will not only be pleasing to the eye, but will stand the test of time: good design, careful workmanship and meticulous selection of materials. You can continue to refine your design on paper, but at some point you will have to make that transition from a two dimensional drawing to selecting the lumber to use for each part. This can be one of the most difficult phases of any project and one that has the greatest effect on the final appearance of your finished piece.
Carpentry skills can be applied to residential or commercial remodeling, cabinet making and exterior and interior trim. Coursework in carpentry classes commonly includes instruction in building safety, construction codes, framing and site layout. These courses are widely available at technical schools and colleges. Hands-on practice is emphasized in most classes.
Once the mixture is made, simply brush the solution on the wood. It won't immediately turn colors, but over a few hours you'll notice a considerable difference. Check out the photos of my farm table project to see how well it worked using fir boards. You'll notice the fir 2×2's used in this project really took the solution well. The other boards had a little coloring and grain enhancement, but white pine doesn't have many tannins in it so it is less reactive.
Having completed this course the learner will be able to: - Describe the history and scope of carpentry as a trade; - Identify the opportunities for carpenters in the construction industry; - Classify the various building materials used by carpenters; - List the most commonly used fasteners and adhesives used by people in the carpentry trade; - Explain the different types of hand and power tools available to carpenters; - Outline the general safety procedures and guidelines that should be followed to operate the tools; - Discuss the importance of employee responsibility and human relations to being successful in the trade; - Identify the various types of construction drawings that make a drawing set; - State the guidelines to read and interpret reading plans and drawings, blueprints, and specifications; - List the various terms associated with floor systems, wall, ceiling and roof framing; - Explain the different methods of framing and constructing houses made of wood; - Describe the types of beams/girders and supports used in construction; - Outline the sequence involved in constructing a platform floor assembly; - Summarize the basic procedure for laying out, assembling, and erecting wood frame walls; - Recognize the different types of roofs used in residential construction; - Determine the length of a common rafter required to construct a roof; - Discuss the terms associated with concrete, concrete reinforcing materials, and formwork; - Apply the concrete mixing information to get different types of concrete, designed to suit various purposes; - Explain the basic concrete curing methods and materials; - List the various components of windows, exterior doors, and stairways used in residential construction; - Summarize the basic installation procedure for pre-hung windows; - State the various types of exterior doors used in residential construction; - Identify the essential requirements for framing stairs; - Describe the design and layout techniques used for stairways and stairwells.
Being without machinery to dimension and dress rough timber myself I can definitely see the benefit, but I think the investment (both in money and space) in machinery like this is premature for ‘basic’ woodworking. Additionally, without some other machinery (table saw, bandsaw) you’re still going to have trouble dimensioning smaller timber for projects from large/rough stock (e.g. producing timber strips for case fronts, ripping to reduce thickness, etc).
Chic white coffee table with blag legs and with amazing natural garden like spell! This happens due to built-in planter that make you feel like you are sitting in a garden while being around this coffee table! Grow your favorite flowers or herbs in the integrated planter or simply use it as an ice box for your beverage parties! Want to copy this versatile table design now? Step-by-step DIY tutorial here abeautifulmess
Description: In this session, I will be demonstrating over 20 ways to mount wood on the lathe for turning. Starting with different methods between centers, I will demonstrate single axis, as well as multi-axis turning. Discussion will then move to various ways to use faceplates, to safely hold your wood blank on the lathe. We will then progress to scroll chucks and screw center usage. Next, will be conversation on the use of homemade chucks, jam chucks, collets and mandrels. I will then demonstrate the use of vacuum chucks, jumbo jaws, doughnut chucks, and Longworth style chucks, and finish up with the use of various types of steady rests, including ring-style, bowl steadies, and spindle supports. This class is geared toward the turner who is interested in learning many different ways to mount pieces of wood in the lathe, and what the advantages or disadvantages might be of different techniques. The student will be expected to watch and learn, but also get involved in the discussion regarding chucking methods, and share some of their experiences as well. This class is designed for all turners, wanting to learn. Please bring eye protection to class.