Dan, my work space that is available for power tools is quite small, about 6′ x 20′. It may seem like a lot on the surface, but a long rectangle is a bear to work in. It requires a lot of serpentine action. That said, I don’t have too much room for large footprint tools. I have settled finally on three big tools; a small bench saw, a thickness planer, and a drill press. I had to forgo the jointer, so I use hand tools to make up for it’s absence (as I do with a lot of my hand tool techniques). I have gotten to the point where I can flatten one side and true an edge of a board reasonably quick. I then finish it up with the thickness planer and table saw, giving me a nice flat board. I guess what I am basically saying is, there’s more than one way to skin a cat, and don’t write off hand tools as a quaint way to experience the past. They worked for thousands of years, and still do! Thanks for the blogs, they make for great reading.
My $0.02 worth. I agree with the thickness planer [mine is 10″] but anything over a 6″ jointer is expensive and space-consuming, so use hand planes as in your later blog. I inherited an 8″ table saw that my dad and I used to build a 12′ outboard boat back in 1955. I’ve used it for ripping, but I’m having second thoughts because of safety issues. Some have suggested a band saw for ripping, which is quieter and safer to use. I gave my router away [and hope to get rid of my Freud biscuit joiner and 6″ jointer]. A quality eggbeater drill works every bit [pun not intended] as well as a power drill, and they cost less. A coping saw and a jewelers saw negate the need for a jigsaw unless you are into making puzzles. Chris Schwarz has a video short on one of the Highland Woodworker series showing how to joint the edge of a board with a plane and a simple jig on the workbench surface. Another reason to bypass the jointer.
It’s good to know that when it comes to choosing wood to buy that there are somethings that we need to take into consideration. I like how you mentioned that one thing we need to consider is whether we need it to be hard or soft for the project we are needing it for. This is something that we will have to look at and do more research on to make sure that we make the right decision.
A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.
Teak is becoming rarer as the days go on, but it is the staple for fine outdoor furniture. Teak is highly weather-resistant and beautiful (not to mention expensive — can you believe almost $24 a board foot?). Teak has an oily feel and a golden-brown color. It rates a 3 on a scale of 1 to 5 for hardness and is only available from larger lumberyards and specialty suppliers.
A coffee table with storage can be a really useful addition to a small living room or pretty much just any lounge space. After all, you can never have too much storage. So let’s see what it takes to build such a table. Well, you could repurpose some elements from an old cabinet if you have any. An already existing drawer could be the starting point for your project. Have a look at these plans from rogueengineer for more inspiration.
I just moved overseas and had to give up all of my power tools due to space limitations and power incompatibility. Upon arrival the first power tool that I bought was a cordless drill/driver and the second was a circular saw. I then modified the saw to improve its performance for cabinet quality work by putting a zero clearance baseplate (just a piece of 1/4″ plywood screwed to the base) this allows the saw to cut plywood panels without tearing up the edges. I also bought a length of aluminum rectangle tube stock for a straight edge. Together the straight edge and the zero clearance baseplate makes the circular saw a fairly accurate tool for plywood construction projects. It’s not as easy to use as a Festool track saw but it cuts almost as clean and cost about 1/5th the price.
Loveland lies in Larimer county, which is one of the 55 counties in Colorado. Overall, the Fort Collins-Loveland area has 128,650 total employed workers according to the US Bureau of Labor Statistics, with a 2% unemployment rate, $21/hr average worker wage, and a $43,210 average annual salary. Thus, about 6 out of every 1000 jobs in Loveland are held by carpenters, and 6/1000 are held by construction laborers.
Just a little nitpick on the tape measure blurb. The hook should not be completely tight. It should move in and out about a 1/16th or the thickness of the hook. This way you get an accurate measurement whether you hook a part to measure or bump up to it. If you want more accurate measurements with a tape measure, “burn” an inch instead of hooking or bumping the part. Just line up what you want to measure with the 1″ mark and subtract that inch from the final measurement.
Rustic furniture look is the hottest furniture look that is chosen to score high value styles and living room fashion trends! So why not get some style-worthy living room coffee table out of some old wood logs? Follow the construction steps and pattern here to get a fab like shown one for good reputation of your living room! Here is the tutorial bhg
When you've selected your lumber, restack the pile neatly. Before heading off, calculate the number of board feet you have pulled just to be sure you have enough. It's advisable to allow for errors, waste and slight changes in plan when purchasing your material. Depending on the material and the complexity of the project I'll typically allow from 10 to 40% extra.
While flipping through the boards, keep an eye open for signs that a number of boards may have come from the same tree. Looking at the ends and the growth rings will tell you where in the log the board was sawn. In some cases, knots may go through more than one board, and often the outer boards have a live edge. By comparing these features, the colouring, grain and other distinguishing marks, it is often possible to identify several boards cut from the same log.
Treeline offers only the finest wood carving tools and supplies. Everything from Treeline is backed by our 30-day guarantee against any defects. We have been providing wood carving tools since 1997 and we strive to excel in customer service and quality products. All employees at Treeline are very knowledgeable and professional, so if you are looking for the right woodcarving tools, contact us and we will do our best to help you.
We are all well aware of the role of a DIY coffee table for a living room which is highly versatile! It is what you need to get first while entertaining some visitors or guests in the living room! The conversations are also to start always by sitting around it! It is seen mostly in the center of the sitting plans! The reason is that all the sitting personages can use it to place their mobile phones, cups, beverage mugs, magazines and other materials over it while they need to get their hands free for the detailed conversations! So this all tells that how utilitarian item a coffee is!
I just moved overseas and had to give up all of my power tools due to space limitations and power incompatibility. Upon arrival the first power tool that I bought was a cordless drill/driver and the second was a circular saw. I then modified the saw to improve its performance for cabinet quality work by putting a zero clearance baseplate (just a piece of 1/4″ plywood screwed to the base) this allows the saw to cut plywood panels without tearing up the edges. I also bought a length of aluminum rectangle tube stock for a straight edge. Together the straight edge and the zero clearance baseplate makes the circular saw a fairly accurate tool for plywood construction projects. It’s not as easy to use as a Festool track saw but it cuts almost as clean and cost about 1/5th the price.
As an entry-level carpentry apprentice, you can expect to earn a percentage of the full pay of a journey-level carpenter. According to national apprenticeship guidelines, you could begin at approximately 30 to 60 percent of a full salary (depending on a number of factors) and receive five-percent increases at set increments (often every 1,000 hours worked) throughout your training. *
If you can buy a bunch of tools at one time, you can save a ton on shipping, as the more you buy, the lower the rates. Also, take advantage of free shipping offers. Compare to see where you can get the best deal. Whatever you buy, make sure it is high quality. I have a Nicholson backsaw I bought at a local store before I knew of the woodworking suppliers. It has never been used much, but cuts much slower than saws such as Gramercy or Lie-Nielsen, even though mine have smaller teeth than the Nicholson.

Scm specializes in designing and manufacturing woodworking machines and services for joineries and customized production shops working with melamine panels, solid wood and other plastic materials. All machines are configured to offer the best technological innovations, high performance and reliability. Easy to install and easy to use, Scm products are distributed all over the world. 
Loveland, CO (population: 68,614) has four carpentry schools within a 100-mile radius of its city center. Emily Griffith Opportunity School, the highest ranked school in this group with a carpentry program, has a total student population of 2,230. It is the 2063rd highest ranked school in the USA and the 22nd highest in the state of Colorado (#1 is Colorado College).
Always be on the lookout for usable wood. You might be able to salvage some. You can use a metal detector to find nails and screws. You don’t need a full fledged metal detector. I use a pinpointer made by Garrett. If your wood has some woodboring beetles you can still use it if not eaten too badly. A healthy dose of cyfluthrin will take care of them.
Description: When you have reached that point in your turning, where you are ready to challenge yourself with something new, this class will teach you some proven techniques for turning simple hollow forms. Students will have the opportunity to use a variety of turning tools and hollowing tools. You will also learn sharpening techniques for these tools. We will also discuss design options and aesthetics, and learn various finishing techniques. All students are encouraged to bring their favorite turning tools to use on this project.
Dan, my work space that is available for power tools is quite small, about 6′ x 20′. It may seem like a lot on the surface, but a long rectangle is a bear to work in. It requires a lot of serpentine action. That said, I don’t have too much room for large footprint tools. I have settled finally on three big tools; a small bench saw, a thickness planer, and a drill press. I had to forgo the jointer, so I use hand tools to make up for it’s absence (as I do with a lot of my hand tool techniques). I have gotten to the point where I can flatten one side and true an edge of a board reasonably quick. I then finish it up with the thickness planer and table saw, giving me a nice flat board. I guess what I am basically saying is, there’s more than one way to skin a cat, and don’t write off hand tools as a quaint way to experience the past. They worked for thousands of years, and still do! Thanks for the blogs, they make for great reading.
1: Table saw in place of a jointer. Any number of tips in previous issues address straightening edges of boards without a jointer. A jointer serves one purpose, but a tablesaw can serve many (just watch your local Craigslist for a decent one to come up.) The thickness planer is unavoidable, but until you can afford one, buy stock in the thickness you need.
All Alison courses are free to enrol, study and complete. To successfully complete this Diploma course and become an Alison Graduate, you need to achieve 80% or higher in each course assessment. Once you have completed this Diploma course, you have the option to acquire official Certification, which is a great way to share your achievement with the world. Your Alison Certification is:
This woodworking plans project is a Bentwood Coffee Table that is a challenging design for those who would like to try a project which requires wood bending. The contemporary lines combined with traditional natural wood allow this table to fit comforatbly with many other styles of furnishings. The technique for bending the wood does not require any special tools or steaming processes.
If you have already completed some college or university education, then many apprenticeship programs will give you credit for prior learning. You can even receive credit for work experience you possess in the construction field. It is important to note that any education and work experience credits will likely be evaluated on a case-by-case basis, so if you want to explore this option, then checking around for the best use of your experience is key.
No matter what type of wood working equipment you are looking for, Hermance is here to help. We offer one of the largest selections of general woodworking machinery online. Whether you're in the market for a boring machine, table saw, dust collector, or even an end matcher- you're sure to find what you're looking for in our listings of general woodworking machinery.
Use a nail gun or hammer and finish nails to connect the cross supports to the upper and lower 2×4 side rails. All outside angles are 60 degrees. The two shorter pieces have an inside angle at 30 degrees. The long piece is 22.5″ from outside edge to to inside edge. The 2 shorter pieces are 11 1/4″ from the inside to outer edge. Click here to see a video I made explaining the angles.
Dan, my work space that is available for power tools is quite small, about 6′ x 20′. It may seem like a lot on the surface, but a long rectangle is a bear to work in. It requires a lot of serpentine action. That said, I don’t have too much room for large footprint tools. I have settled finally on three big tools; a small bench saw, a thickness planer, and a drill press. I had to forgo the jointer, so I use hand tools to make up for it’s absence (as I do with a lot of my hand tool techniques). I have gotten to the point where I can flatten one side and true an edge of a board reasonably quick. I then finish it up with the thickness planer and table saw, giving me a nice flat board. I guess what I am basically saying is, there’s more than one way to skin a cat, and don’t write off hand tools as a quaint way to experience the past. They worked for thousands of years, and still do! Thanks for the blogs, they make for great reading.
First, build two boxes for each leg assembly. These are attached using wood glue and 2.5” pocket hole screws through the horizontal boards and into the vertical boards.  You want your pocket holes facing the outside of the box on this part because we will cover them with another board on the next part.  We used our K5 Kreg Jig for this part.  We get asked ALL the time which Kreg Jig to start with.  We always suggest the K5.  We use it on almost every build.  You can find it HERE on Amazon! 

Products and systems by Lamello have always been Products and systems by Lamello have always been designed for longevity and reliability. This legendary durability is combined with environmental stewardship in view as strict environmental regulations at our production site in Switzerland ensure that all resources are used with consideration many of them stemming from sustainable husbandry and management. ...  More + Product Details Close
Carpentry students from Loveland schools who go on to become carpenters, construction managers, construction workers, construction engineers, etc. have a good chance at finding employment. For example, there are 743,760 people working as carpenters alone in the US, and their average annual salary is $43,640. Also, Construction laborers make on average $33,190 per year and there are about 856,440 of them employed in the US today. In fact, in the Fort Collins-Loveland area alone, there are 760 employed construction laborers earning an average salary of $29,460. Carpenters in this area earn $39,170/yr and there are 770 employed.
A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.
I’m currently working on a dining room table with this color in mind (I also plan on a coffee table soon). I’ve been testing out stain colors and dark walnut is currently in the lead. I love the way this coffee table turned out in color. How many coats of stain did you use? Also, did the dark wax make a big difference in color? I was planning on using a satin poly for sealant (mostly because it’s what is most convenient and what I’m accustomed to), but I’m interested in the dark wax after seeing this post. Any recommendations you have are much appreciated.
The coffee table is most often the furniture piece which sits at the very heart of spaces such as the living room, outdoor lounge or pretty much any sitting area no matter the size or style. In these conditions, the coffee table is a focal point for that space and takes on a very special role. It’s often the piece which ties together the whole decor around it. There are, naturally, lots of possible designs and looks for such an element so we’ve prepared a set of inspiring coffee table plans which you might find useful if you’re ever interested in building your own furniture.
Introductory carpentry classes provide students with an overview of the methods and technologies used in residential and light commercial carpentry and are typically taken at the beginning of a carpentry program. Hands-on experience and lectures make up the class content, which can cover building codes, site layout, estimating, interior and exterior finishes, framing and cabinetry. Additional subjects of instruction may include footing and foundation forming, concrete specifications, OSHA/WISHA construction safety standards and basic carpentry math.
Hands-on techniques are generally introduced in this course, which covers exterior moisture, interior and exterior doors, window trim installation and custom built-in cabinetry. When studying interior finish features, students learn about sheet rock, taping and texturing and cabinet installation. Coursework on exterior finish features may include estimating time and costs, framing, laying out rafters for roofs and installing outside doors and windows. This course is taken after introductory courses.
Online carpentry education opportunities may be offered as certificate programs or as career diplomas. In programs like these, you'll practice basic carpentry in addition to studying building codes, blueprint reading, math and business management. The courses will typically cover roofing, wall paneling, wood-joining techniques and materials estimation, among other topics. You'll also learn how to use hand and power tools. Depending on the program, you might even take a Spanish course.
The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.
“Basic,” on the other hand, is a word that allows for growth – and that’s exactly what you want in your woodworking tool kit. You want to be able to take the same kit with you through many years in the craft. With my basic woodworking tools list, I wanted to provide a core set of tools that will serve you well from project to project. I’m especially concerned these days with the transition to hardwood furniture making, as opposed to plywood boxes of various sizes. That’s the transition I’m making right now in my own work!
Online carpentry education opportunities may be offered as certificate programs or as career diplomas. In programs like these, you'll practice basic carpentry in addition to studying building codes, blueprint reading, math and business management. The courses will typically cover roofing, wall paneling, wood-joining techniques and materials estimation, among other topics. You'll also learn how to use hand and power tools. Depending on the program, you might even take a Spanish course.
A successful joiner can see the full picture of the project he is preparing to run and for SCM woodworking machinery come to his aid with devices made especially for woodworking machinery; devices that allow to not having to perform the mathematical calculations necessary to make a precise angular cut on a circular saw (with our compex for example) or a template that can produce pieces that are exactly identical among them (on our lathe minimax t 124).
×