Woodworking is an ancient art that requires an artistic eye and precise tools. Whether you're starting off in woodworking or you're an established woodworker, you need good woodworking machinery to help you create your art. A good knowledge of the major machines and how they help you when working with wood can go a mile in making the woodworker’s job easier.
This is also a table made from a repurposed pallet. There’s not much you need to change about the pallet, except rearrange a few boards and make the frame smaller. The fact that each board has a slightly different color tone gives the table a special charm. The hairpin legs are a really nice touch. Check out the full tutorial to find out more about how you can build something similar for your own home.
I needed a new coffee table for the living room and this design fit the bill perfectly. I came across a table from Ana-White.com that I loved, but modified it a bit because I wanted a breadboard style top. To see her plans click here. The difference between the table in this post is that I cut the top pieces to 41″ (vs 52″) and added the 2×6 pieces to each end, making it come to 52″ with a breadboard style top.
The Amish here in Ohio use a nifty wooden rule for calculating bd. ft. It has a brass football shaped hook on the end and they’re about 2′ long. Three columns of numbers run down the length of stick. These columns are the length of stock say, 12,14,16 foot. Within these columns, bd. ft. has already been calculated and marked. For a 16′ bd. the hook is placed over one edge and a reading of bd. ft. is taken from opposite edge from the 16′ column. “Audels Carpenters and Builders Guide #1” pg. 146, shows a good example. They call… Read more »
Apply glue to the ends of the 1 x 2 End Pieces for the Base and Apron, and then clamp them in place against the inside of the Leg. Position the pieces so that one runs flush with the top edge, and the other sets below the line marked in Step 7. Center both pieces on the leg, and tilt them so that they run parallel to the edge of the Leg. Using a drill/driver and 1¼-inch pocket holes screws, attach the pieces to the Leg. Repeat on the opposite end.
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience. 
Rough lumber is sold and measured in ¼" increments; when a board is referred to as 4/4, it means it is four quarters of an inch thick, or one inch. The most common sizes you are likely to encounter at the lumber yard are 4/4 (1"), 6/4 (1½"), 8/4 (2") and 12/4 (3"). Generally, larger dimension lumber is priced per board foot. Price is also dependant upon the wood quality. Boards without blemishes, and of even colour, command higher prices. On most projects it isn't necessary to purchase the best grade material for the entire project. Purchasing a lower grade will allow you to bring home more lumber, and give you the freedom to lay out parts based on appearance rather than waste.
About forty years ago I purchased a Shopsmith Mark V because I lacked space for a large shop, and also moved around the United States a lot. Later I purchased another Shopsmith Mark V Model 510 for the increase in table size and flexibility. I do wood working as a hobby, not to do many projects as fast as possible. I also have every tool and accessory that Shopsmith makes for the two primary tools. Their quality is excellent, and while I enjoy antique tools like the 1912 three phase electric Camel Back Drill Press I purchased for my son’s shop, the Shopsmith does every thing I have ever needed.
This course introduces students to the craft of creating custom built cabinetry through practical application and classroom instruction. Students begin by learning how to design and build basic box cabinets. Other topics include standard cabinet sizes and specifications, types of lumber and sheet material, basic terminology, joinery techniques and safety operations. Students work on their own or with others to create a variety of projects such as kitchen cabinets, built-in shelves or closet storage units.
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience. 
Loveland, CO (population: 68,614) has four carpentry schools within a 100-mile radius of its city center. Emily Griffith Opportunity School, the highest ranked school in this group with a carpentry program, has a total student population of 2,230. It is the 2063rd highest ranked school in the USA and the 22nd highest in the state of Colorado (#1 is Colorado College).

Delta 22-590 13 in. portable thickness planer includes: Delta 22-590 13 in. portable thickness planer includes: 3 cutting knives cutter head wrench dust chute with 4 in. port and magnetic blade changing tool. High-speed steel indexed double-sided knives provides 2X blade life and allows for quick blade changes. Oversized cutter head height adjustment handle with indexing ring provides ...  More + Product Details Close
Description: This workshop is designed for those who have recently gotten a wood lathe, or have had one for a while, and haven't gotten around to using it until now. During this workshop students get acquainted with the wood lathe and its parts and accessories. We will cover the turning process, as well as sanding and applying finish to a project while it's on the lathe. Students will also be shown a variety of turning tools and how they function. You will also be introduced to wood selection, tool selection, and tool sharpening. Students will test their skills while working on a small turning project. Students should bring suitable eye protection such as safety glasses, goggles, or a face shield. If you have problems with wood dust, a respirator or dust mask would be advisable. Also bring any wood turning tools you might have. Tools and safety gear will be provided for those who don't own them. Materials for turning will be provided.
Industrial carpenters work on civil engineering projects and in industrial settings, where they build scaffolding and create and set forms for pouring concrete. Some industrial carpenters build tunnel bracing or partitions in underground passageways and mines to control the circulation of air to worksites. Others build concrete forms for tunnels, bridges, dams, power plants, and sewers.

The owners, webmasters, administrators, authors and editors, expressly disclaim all and any liability to any person, whether a user of this website or not, in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance, whether whole or partial, upon the whole or any part of the contents of this website. Please exercise caution when working with any tools or machinery. Follow common safety rules and precautions as outlined in any manuals related to the equipment being used. If advice or other expert assistance is required, the services of a competent professional person should be sought.

Like you, I too am benchless. I built the “Mozilla” Molson vice variant from last year’s issue (I forget which) and it comes in handy for a lot of operations. I clamp it down to a piece of plywood that I have covered with formica (actually, it’s two pieces that I have piano-hinged together for easier storage) laid across two sawhorses. As long as lateral thrust is not involved, this is a pretty stable way to work. I also have a Zyliss vise for working on smaller pieces. I’ve made do for nearly forty years with a radial arm saw and circular saw. I have only recently acquired a planer and router table (both on wheels) It makes the garage croweded because also sharing the space are two motorcycles and about 400 board feet of rough sawn Camphor. I currently attend classes in woodworking and this coming semester I’ll be enrolled in a class for handtools only (and sharpening).
While flipping through the boards, keep an eye open for signs that a number of boards may have come from the same tree. Looking at the ends and the growth rings will tell you where in the log the board was sawn. In some cases, knots may go through more than one board, and often the outer boards have a live edge. By comparing these features, the colouring, grain and other distinguishing marks, it is often possible to identify several boards cut from the same log.
It all depends on the program. Some programs are designed for those already working in the construction industry. Other programs are open to anyone, regardless of their background. Some classes have a specific date by which you must have all of your work completed. Others impose no time limits and give you an unlimited timeframe to complete your work.
One subject that a woodworker must always consider when building a project is how seasonal moisture and temperature fluctuations will cause expansion and contraction of the wood stock in the assembled project. For instance, if you've ever experienced a drawer that sticks only in the winter time, you've experienced seasonal movement of wood. Since each wood species is affected by these temperature and moisture fluctuations, you'll need to know a bit about the climate where the project will be used, and how your chosen wood stock is affected by the climate changes. Again, your local woodworking supplier can be a great resource for answering these types of questions in your area.

Even though this is in fact a side table, we can definitely find inspiration in its design. We find this project to be highly creative and interesting. The table has a hexagon-shaped top and bottom connected by two sets of five rods. Two in each set are longer than the other and go through the bottom hexagon, acting as legs. You can find the plans for this project on ohohblog.


I’m currently working on a dining room table with this color in mind (I also plan on a coffee table soon). I’ve been testing out stain colors and dark walnut is currently in the lead. I love the way this coffee table turned out in color. How many coats of stain did you use? Also, did the dark wax make a big difference in color? I was planning on using a satin poly for sealant (mostly because it’s what is most convenient and what I’m accustomed to), but I’m interested in the dark wax after seeing this post. Any recommendations you have are much appreciated.


For furniture making, the best, most stable stock has the annual growth rings intersecting each face at approximately the same angle, roughly 45º. Wood cut this way is referred to as quarter sawn. Milling quarter sawn lumber is a labour intensive process, which is why it costs more than plain-sawn lumber. The appearance of the grain will tend to be similar on all four sides. This makes quarter sawn lumber a great choice for table legs, rails and stiles of frame and panel doors, or for any part where two adjacent sides are visible.


Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!
×