A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.
By the end of this course, you will have a strong grasp of the most important elements of carpentry. This will be a great boost to your carpentry skills and career. With carpentry being such an important part of the construction industry, you will be preparing yourself for a job for life. And even if you don’t want to earn money as a carpenter, the skills you will learn here will allow you to fix almost anything around your home, and maybe make a nice gift or piece of furniture for a friend, partner, or yourself. Not bad for a course that takes less than 10 hours.

The topic of lumber confused me mainly because I couldn’t find a simple summary of the topic. I found a lot of complex discussions with different terms used by different “experts”. I am by no stretch of the imagination a lumber expert, but I’m very good at simplifying complex topics so that everyone can understand. As a result, this is a simple practical guide to help you understand how wood moves, what wood to buy, how to buy it, and where to buy it.


Apply glue to the ends of the 1 x 2 End Pieces for the Base and Apron, and then clamp them in place against the inside of the Leg. Position the pieces so that one runs flush with the top edge, and the other sets below the line marked in Step 7. Center both pieces on the leg, and tilt them so that they run parallel to the edge of the Leg. Using a drill/driver and 1¼-inch pocket holes screws, attach the pieces to the Leg. Repeat on the opposite end.
I think it depends on the type of woodworker you would like to become. Are you more interested in traditional “electric free” carpentry or are you drawn to the ease and convenience of modern machinery? Also, I think you should take into consideration what kind and how much shop space you have available. I have worked with all the modern machines for years now, and are just presently finding personal satisfaction in traditional woodworking. In fact, last night I built my very first bookcase with just a few “powerless” hand tools. So in all, I would suggest some personal reflection…What type of woodworker do you want to become?…and from there garnish your shop appropriately. 

11-2. Pipe clamps, I have about 10 of them with varying lengths of black pipe in 1′ increments. I can switch out the clamps for larger lengths on larger projects, or downsize as needed. (very rarely do I need more than 6 clamps on a project during drying time, and when I do, it’s time for a cup of coffee and a 1/2 hour break while I wait) You keep your initial investment down, and buy them as you need them to increase your collection.
As an entry-level carpentry apprentice, you can expect to earn a percentage of the full pay of a journey-level carpenter. According to national apprenticeship guidelines, you could begin at approximately 30 to 60 percent of a full salary (depending on a number of factors) and receive five-percent increases at set increments (often every 1,000 hours worked) throughout your training. *
Loveland lies in Larimer county, which is one of the 55 counties in Colorado. Overall, the Fort Collins-Loveland area has 128,650 total employed workers according to the US Bureau of Labor Statistics, with a 2% unemployment rate, $21/hr average worker wage, and a $43,210 average annual salary. Thus, about 6 out of every 1000 jobs in Loveland are held by carpenters, and 6/1000 are held by construction laborers.
Lumber for your projects can come from many sources, but before you can use it to build anything, it must be dry. Lumber that is kiln dried will have a moisture content right out of the kiln of 7 or 8%. However, by the time the lumber is delivered to your local dealer and arrives at your shop, the moisture content may have changed dramatically. Storage conditions between the kiln and your shop are clearly out of your control, so it is always a good idea after purchasing lumber to acclimatize it in your shop for several weeks. To avoid using lumber that is still in the process of adjusting to its new environment it is best to use a moisture meter to verify the moisture content of the wood. Most dealers don't mind customers checking the moisture content at the yard as long as they are using a pinless meter. The meter in my lumber kit uses electromagnetic waves to calculate the moisture content of a given piece of wood. Its use couldn't be simpler or quicker – simply turn it on, enter the species, and place the meter on the wood to be measured. The result is displayed right on the screen instantly without the need for conversion tables and other calculations. Typically, I check a couple of areas on each board as I select them just to confirm they are all in the same moisture range. Back at the shop I once more check each piece of wood and note it in chalk on the board. Every few days I'll recheck the boards, and when the readings have stabilized, I can be reasonably certain there won't be any surprises when I start the milling process.
I work with a lot of rough sawn boards (Wood Mizer) that are up to 12 inches wide. The worse defect is twist. First I saw the stock to rough project lengths and then using winding sticks, I attack the twist with a #5 hand plane, gradually moving the winding sticks toward the center. If there is bow or cup I can plane that out also. I now have a reference surface that can go thru my planer. The finished boards are perfect. This is not really difficult or excessively time consuming.
As an entry-level carpentry apprentice, you can expect to earn a percentage of the full pay of a journey-level carpenter. According to national apprenticeship guidelines, you could begin at approximately 30 to 60 percent of a full salary (depending on a number of factors) and receive five-percent increases at set increments (often every 1,000 hours worked) throughout your training. *

Cut 2- 1x6 46" boards, mitered at 45 degrees on each end (measurement is taken on long side). Cut 2- 1x6 17" boards, mitered at 45 degrees on each end (measurement is taken on long side). Drill pocket holes in both ends of each board. Drill several pocket holes (3 or 4) on the INSIDE edges of each board. Spread wood glue on the edges of each board, and sandwich them together, using bar clamps to keep them tight. Using 1 1/4" pocket hole screws, attach the 1x4's together. (see photo on previous step)


While flipping through the boards, keep an eye open for signs that a number of boards may have come from the same tree. Looking at the ends and the growth rings will tell you where in the log the board was sawn. In some cases, knots may go through more than one board, and often the outer boards have a live edge. By comparing these features, the colouring, grain and other distinguishing marks, it is often possible to identify several boards cut from the same log.

Poplar is one of the less expensive hardwoods. It’s also fairly soft (1 in hardness on a scale of 1 to 5), which makes it easy to work with. Poplar is white with some green or brown streaks in the heartwood. Because poplar is not the most beautiful wood, it’s rarely used in fine furniture, and if it is, it’s almost always painted. Poplar can be a good choice for drawers (where it won’t be seen) because it is stable and inexpensive. You can find poplar at larger home centers, but a lumberyard will have a better selection.
About forty years ago I purchased a Shopsmith Mark V because I lacked space for a large shop, and also moved around the United States a lot. Later I purchased another Shopsmith Mark V Model 510 for the increase in table size and flexibility. I do wood working as a hobby, not to do many projects as fast as possible. I also have every tool and accessory that Shopsmith makes for the two primary tools. Their quality is excellent, and while I enjoy antique tools like the 1912 three phase electric Camel Back Drill Press I purchased for my son’s shop, the Shopsmith does every thing I have ever needed.
Hardwoods come from deciduous, or broad-leaved trees, as opposed to softwoods, that are harvested from from evergreens. In general, the lumber derived from hardwood species are typically harder than softwoods, although there are exceptions (balsa wood is very light and soft, but is considered a hardwood). Most hardwood tree species lose their leaves in winter, and generally offer a much wider variety of colors and textures than softwoods. Typically, stock from hardwood species are a lot more expensive than those from softwoods.
Carpentry is a very practical and valuable skill. With carpentry you can build a house, make custom furniture, fix things around your home, and have a very profitable and steady career. As long as people need to build homes, people need carpenters. But carpentry is constantly evolving. To be a successful carpenter, you must be aware of modern safety measures and best practices. This course is designed to make sure you know the most important elements of modern carpentry.
An assortment of chisels should be part of every workbench. Chisels are not just for wood carvers. Any woodworker will need chisels to clean out joints and saw cuts. Look for chisels made of high-alloy carbon steel or chromium-vanadium alloyed steel. Hardwood grips are best, especially if they have metal caps on them. This will keep the end of the handle from becoming malformed when you hammer on it.
This is also a table made from a repurposed pallet. There’s not much you need to change about the pallet, except rearrange a few boards and make the frame smaller. The fact that each board has a slightly different color tone gives the table a special charm. The hairpin legs are a really nice touch. Check out the full tutorial to find out more about how you can build something similar for your own home.
We have a bunch of other interesting designs to show you as well. Some, like this one, are meant to make the area around them feel inviting and cozy so the design is simple and familiar. These coffee table plans come from ana-white. You can make them your own by customizing certain aspects of the project. For instance, you could choose to paint the wood and then give it a distressed look instead of using wood stain.
Coffee tables are more of a North American furniture piece, you typically will not find these in England, for which this coffee table is designed after. With a country-style look and rugged appearance of an old workbench, the tapered legs and deep v-grooves on the top with breadboard ends given the appearance of strength and durability. View the Larger Image Slideshow to see the actual paper plan you are buying.
I’m currently working on a dining room table with this color in mind (I also plan on a coffee table soon). I’ve been testing out stain colors and dark walnut is currently in the lead. I love the way this coffee table turned out in color. How many coats of stain did you use? Also, did the dark wax make a big difference in color? I was planning on using a satin poly for sealant (mostly because it’s what is most convenient and what I’m accustomed to), but I’m interested in the dark wax after seeing this post. Any recommendations you have are much appreciated.
While flipping through the boards, keep an eye open for signs that a number of boards may have come from the same tree. Looking at the ends and the growth rings will tell you where in the log the board was sawn. In some cases, knots may go through more than one board, and often the outer boards have a live edge. By comparing these features, the colouring, grain and other distinguishing marks, it is often possible to identify several boards cut from the same log.
In this article, I have described some most important coffee table woodworking projects. There are numerous coffee table woodworking projects available in the market. Some significant table may include a rustic coffee table, the beverage pallet coffee table, modern pallet coffee table, glass topped coffee table, storage coffee table plans, apothecary coffee table, multi-function coffee table, wine crate coffee table, concrete coffee tables and sturdy coffee table. You can use these coffee tables for different purposes such as for home or shop.
Wow, what a great problem to have Boris! If you can send some photos I’ll look at them. But unseen, I’d ask them to try to get some quartersawn boards out, and also some full width flatsawn boards. It just depends on how much wood you’ll get if you quartersaw it. It also depends on what you think you’ll build down the road. Some furniture pieces don’t need to be quite as stable as others. Good luck!
Thanks for the feedback. We’re glad you found the list helpful. Please note that this page contains only 10 of the 40 top tools for woodworking, displaying only hand tools. You can find the next 10 here: https://www.wagnermeters.com/top-40-woodworking-tools-2/. There are links at the bottom of each article to the next group of tools so you can view the entire list. Hope this helps.
Like you, I too am benchless. I built the “Mozilla” Molson vice variant from last year’s issue (I forget which) and it comes in handy for a lot of operations. I clamp it down to a piece of plywood that I have covered with formica (actually, it’s two pieces that I have piano-hinged together for easier storage) laid across two sawhorses. As long as lateral thrust is not involved, this is a pretty stable way to work. I also have a Zyliss vise for working on smaller pieces. I’ve made do for nearly forty years with a radial arm saw and circular saw. I have only recently acquired a planer and router table (both on wheels) It makes the garage croweded because also sharing the space are two motorcycles and about 400 board feet of rough sawn Camphor. I currently attend classes in woodworking and this coming semester I’ll be enrolled in a class for handtools only (and sharpening).
The multi-function coffee table creation can assist as a picnic ensemble, coffee table, and storage unit all in one. Spread your creations and reprocess wooden pallets into reasonable pieces you possibly utilize for a long time. Many individual use this type of coffee table their homes for the reason that you can use this table for different purposes.
Cherry is a very popular and all-around great wood; easy to work with, stains and finishes well with just oil, and ages beautifully. Cherry’s heartwood has a reddish-brown color to it and the sapwood is almost white. Cherry has a hardness of 2 on a scale of 1 to 5. This is a very common wood for furniture-making and is available from sustainably grown forests. You won’t find cherry at your local home center, so a trip to the lumberyard is necessary if you want to use it. Because it’s in demand, cherry is getting somewhat expensive compared to other domestic hardwoods, such as oak and maple.
Industrial carpenters work on civil engineering projects and in industrial settings, where they build scaffolding and create and set forms for pouring concrete. Some industrial carpenters build tunnel bracing or partitions in underground passageways and mines to control the circulation of air to worksites. Others build concrete forms for tunnels, bridges, dams, power plants, and sewers.
The campaign features a new customer-focused website, new advertising centered on visually-appealing wood applications, and the launch of Northwest Hardwoods’ Pinterest and Instagram accounts to convey visual ideas and aspirations for the many uses of hardwoods. The campaign offers an opportunity for Northwest Hardwoods to reach out to new audiences including designers, specifiers, architects and OEMs, underscoring the fact that no other building and design material is as visually appealing and as sustainable as timber. Additionally, the campaign includes the creation of product specific communications outreach that will support the company’s sales objectives.
We cut the decorative diagonal pieces to fit on this part. Mark each board with your pencil and cut them to fit exact. You can check out the video if you have questions about this part! We walk you through it. Cut the diagonal pieces to fit first, then mark and attach them to each other using wood glue and nails. Then, fit them in the box and attach them with wood glue and nails through the box and into each end of the X piece.

If you have some experience working with steel and welding pieces together you’ll find this project a piece of cake. These coffee table plans come from instructables. The base has to be welded and that takes a bit of skill and time and then the top is added. The combination of wood and steel is a pretty harmonious ones. The warmth of the wood combined with the rugged-industrial look of the steel result in a beautiful and well-balanced structure.
Chic white coffee table with blag legs and with amazing natural garden like spell! This happens due to built-in planter that make you feel like you are sitting in a garden while being around this coffee table! Grow your favorite flowers or herbs in the integrated planter or simply use it as an ice box for your beverage parties! Want to copy this versatile table design now? Step-by-step DIY tutorial here abeautifulmess
This course introduces students to remodeling practices and demolitions. Students learn how to plan a remodeling project, complete basic plumbing and electrical jobs, apply for permits, match finished materials and estimate costs. Instruction in reading architectural blueprints for residential remodels is generally included, and students become familiar with specifications, codes and construction drawings. Some residential remodeling courses provide hands-on learning experience by requiring group or individual remodeling projects. This course is usually taken after basic carpentry courses.
This is a vintage woodworking plan. Visit our FAQ page for a full definition. View the Larger Image Slideshow to see the actual item you are buying. A fine new design just added to our Colonial group is the Wagon Seat Coffee table, patterned in full-size. You will admire its beautiful lines and appreciate its sturdy construction. The well shaped, open gallery and four shelf pegs add to its appearance. Its two drawers are handy for small storage, and the shelves are useful for holding a few magazines or books. Build it of pine or hardwood and finish it with a stain and lacquer of high quality. Then wax it and rub it, and you will have a piece of furniture that will mellow as it improves with time.

By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
Description: Every woodturner enjoys the opportunity to give handmade ornaments to friends and family during the holidays, especially one that is made purely out of wood. No pre-made ornament kits or ornament hardware will be used in this class. One might call it au naturel!!!! During this class you will be given the opportunity to see various ornaments that have been turned on the lathe, ranging from small and simple to large and more decorative. Class objectives include, but are not limited to, the following: Wood choice (more common ornament wood species and pros and cons of each) Discussion and demonstration on how ornaments can be colored using a variety of markers, paints, dyes, and gilder's paste. Discuss and demonstrate how a variety of gouges and tools can be used to make ornaments, including texturing tools. Sharpening techniques - the instructor will assist all students when sharpening tools Ornament rough sketch and design, before the wood is on the lathe. Most important, every student in class will be given the opportunity to turn at least one ornament of their own. The instructor will assist with basic sketch and design, and will rotate among all students to assist with cuts, tool use, technique, sharpening, and helpful hints. Experience level: Beginner (some turning experience highly preferred) Suggested tools: Turning tools will be supplied; however, students are encourage to bring their own tools if they have them. 3/8" or 1/2" spindle gouge, narrow parting tool, and small roughing gouge is a great start. Students who wish to bring their own chuck may do so as well (1"-8 tpi, 2" or 50mm dovetail jaws, and pin jaws). Lunch break from 12:00 to 12:45
Treeline offers only the finest wood carving tools and supplies. Everything from Treeline is backed by our 30-day guarantee against any defects. We have been providing wood carving tools since 1997 and we strive to excel in customer service and quality products. All employees at Treeline are very knowledgeable and professional, so if you are looking for the right woodcarving tools, contact us and we will do our best to help you.
About forty years ago I purchased a Shopsmith Mark V because I lacked space for a large shop, and also moved around the United States a lot. Later I purchased another Shopsmith Mark V Model 510 for the increase in table size and flexibility. I do wood working as a hobby, not to do many projects as fast as possible. I also have every tool and accessory that Shopsmith makes for the two primary tools. Their quality is excellent, and while I enjoy antique tools like the 1912 three phase electric Camel Back Drill Press I purchased for my son’s shop, the Shopsmith does every thing I have ever needed.
I consider this my “basic” tool list. Although I do not have a dedicated box for these tools, I assure you that they have a great home in cabinets, on shelves, and laying around on benches. When I do need to take my hand tools somewhere, the larger tools end up in a simple tongue and grooved latch box my grandfather owned. The smaller tools are always in my overall pockets. Overalls work great. They have multiple pockets, they’re comfortable, and they protect your upper body and legs. You only have to deal with small chunks of wood getting into the pockets, which can be dealt with if you or your other half are crafty enough to sew some flaps. It doesn’t bother me though. Thanks for your time.

“Basic,” on the other hand, is a word that allows for growth – and that’s exactly what you want in your woodworking tool kit. You want to be able to take the same kit with you through many years in the craft. With my basic woodworking tools list, I wanted to provide a core set of tools that will serve you well from project to project. I’m especially concerned these days with the transition to hardwood furniture making, as opposed to plywood boxes of various sizes. That’s the transition I’m making right now in my own work!
Doesn’t this table look exquisite? It’s a bit surprising to find out that it’s a DIY piece and that you could make something just as awesome without too much effort. You need some MDF, wooden tapered legs, angle top hardware plates, a jigsaw, a screwdriver and spray paint. The trickiest part is cutting the MDF board and giving it the desired shape. Luckily, there’s a tutorial on thewonderforest which can give you some pointers.
11-2. Pipe clamps, I have about 10 of them with varying lengths of black pipe in 1′ increments. I can switch out the clamps for larger lengths on larger projects, or downsize as needed. (very rarely do I need more than 6 clamps on a project during drying time, and when I do, it’s time for a cup of coffee and a 1/2 hour break while I wait) You keep your initial investment down, and buy them as you need them to increase your collection.
Lumber for your projects can come from many sources, but before you can use it to build anything, it must be dry. Lumber that is kiln dried will have a moisture content right out of the kiln of 7 or 8%. However, by the time the lumber is delivered to your local dealer and arrives at your shop, the moisture content may have changed dramatically. Storage conditions between the kiln and your shop are clearly out of your control, so it is always a good idea after purchasing lumber to acclimatize it in your shop for several weeks. To avoid using lumber that is still in the process of adjusting to its new environment it is best to use a moisture meter to verify the moisture content of the wood. Most dealers don't mind customers checking the moisture content at the yard as long as they are using a pinless meter. The meter in my lumber kit uses electromagnetic waves to calculate the moisture content of a given piece of wood. Its use couldn't be simpler or quicker – simply turn it on, enter the species, and place the meter on the wood to be measured. The result is displayed right on the screen instantly without the need for conversion tables and other calculations. Typically, I check a couple of areas on each board as I select them just to confirm they are all in the same moisture range. Back at the shop I once more check each piece of wood and note it in chalk on the board. Every few days I'll recheck the boards, and when the readings have stabilized, I can be reasonably certain there won't be any surprises when I start the milling process.

Additionally, after becoming a journey level carpenter, you can go on to obtain master certification, which typically requires multiple years of consecutive experience as a journeyworker. This can help you earn a higher wage or qualify for teaching or management roles. You can even take on your own apprentices, allowing you to share your expertise with the next generation of professionals.


If you have some experience working with steel and welding pieces together you’ll find this project a piece of cake. These coffee table plans come from instructables. The base has to be welded and that takes a bit of skill and time and then the top is added. The combination of wood and steel is a pretty harmonious ones. The warmth of the wood combined with the rugged-industrial look of the steel result in a beautiful and well-balanced structure.
However, if you want to stain or clear-coat the project, you'll have a number of choices to look through. Since your local home center megamart will probably only carry a couple of hardwood species (poplar and red oak are common) spend time at a fine wood supplier and look through the vareties available. They should be able to help you determine how each species will look when finished, which will go a long way toward refining your decision. 

Upcycling and recycling are our mottoes thus it is just natural for old door tables’ transformations to be a segment of a collection of our free point, particularly when this kind of crafts and projects have a reused material and sustainable side enriched by the passage of period. Old wooden door recycled into the table is a very good technique for beginners.
This woodworking plans project is a Bentwood Coffee Table that is a challenging design for those who would like to try a project which requires wood bending. The contemporary lines combined with traditional natural wood allow this table to fit comforatbly with many other styles of furnishings. The technique for bending the wood does not require any special tools or steaming processes.
More than a decade ago I spent 2 weeks in Maine aspiring to learn furniture making. On my return home I started enthusiastically planning to turn my basement into a proper shop – with all the “essential” tools I had learned to use. My list reflected my engineer’s preference for buying quality and quickly exceeded $25k in power tools alone (table saw, band saw, joiner, thickness planer, drill press…) even before solving the power, lighting and dust challenges.

At Able Skills we pride ourselves in the diversity of the skills that are available within our carpentry training centre. If upon completion of this course you would like to learn much more then you can consider upgrading to City & Guilds Certificate & Training to NVQ Level 2. This would require you to train for an additional 5 weeks; payment would be adjusted to reflect what you have already paid on this course.
If you have some experience working with steel and welding pieces together you’ll find this project a piece of cake. These coffee table plans come from instructables. The base has to be welded and that takes a bit of skill and time and then the top is added. The combination of wood and steel is a pretty harmonious ones. The warmth of the wood combined with the rugged-industrial look of the steel result in a beautiful and well-balanced structure.
Description: In this session, I will be demonstrating over 20 ways to mount wood on the lathe for turning. Starting with different methods between centers, I will demonstrate single axis, as well as multi-axis turning. Discussion will then move to various ways to use faceplates, to safely hold your wood blank on the lathe. We will then progress to scroll chucks and screw center usage. Next, will be conversation on the use of homemade chucks, jam chucks, collets and mandrels. I will then demonstrate the use of vacuum chucks, jumbo jaws, doughnut chucks, and Longworth style chucks, and finish up with the use of various types of steady rests, including ring-style, bowl steadies, and spindle supports. This class is geared toward the turner who is interested in learning many different ways to mount pieces of wood in the lathe, and what the advantages or disadvantages might be of different techniques. The student will be expected to watch and learn, but also get involved in the discussion regarding chucking methods, and share some of their experiences as well. This class is designed for all turners, wanting to learn. Please bring eye protection to class.
×