As an entry-level carpentry apprentice, you can expect to earn a percentage of the full pay of a journey-level carpenter. According to national apprenticeship guidelines, you could begin at approximately 30 to 60 percent of a full salary (depending on a number of factors) and receive five-percent increases at set increments (often every 1,000 hours worked) throughout your training. *
Apply glue to the ends of the 1 x 2 End Pieces for the Base and Apron, and then clamp them in place against the inside of the Leg. Position the pieces so that one runs flush with the top edge, and the other sets below the line marked in Step 7. Center both pieces on the leg, and tilt them so that they run parallel to the edge of the Leg. Using a drill/driver and 1¼-inch pocket holes screws, attach the pieces to the Leg. Repeat on the opposite end.

There are often situations when the original message asks for opinions: "What is the best widget for my type of shop?". To a certain extent, the person posting the message is responsible for including specific questions within the message. An open ended question (like the one above) invites responses that may read as sales pitches. WOODWEB suggests that companies responding to such a question provide detailed and substantive replies rather than responses that read as a one-sided product promotion. It has been WOODWEB's experience that substantive responses are held in higher regard by our readers (return to top). 

Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!
Chic white coffee table with blag legs and with amazing natural garden like spell! This happens due to built-in planter that make you feel like you are sitting in a garden while being around this coffee table! Grow your favorite flowers or herbs in the integrated planter or simply use it as an ice box for your beverage parties! Want to copy this versatile table design now? Step-by-step DIY tutorial here abeautifulmess
I just moved overseas and had to give up all of my power tools due to space limitations and power incompatibility. Upon arrival the first power tool that I bought was a cordless drill/driver and the second was a circular saw. I then modified the saw to improve its performance for cabinet quality work by putting a zero clearance baseplate (just a piece of 1/4″ plywood screwed to the base) this allows the saw to cut plywood panels without tearing up the edges. I also bought a length of aluminum rectangle tube stock for a straight edge. Together the straight edge and the zero clearance baseplate makes the circular saw a fairly accurate tool for plywood construction projects. It’s not as easy to use as a Festool track saw but it cuts almost as clean and cost about 1/5th the price.
Birch comes in two varieties: yellow and white. Yellow birch is a pale yellow-to-white wood with reddish-brown heartwood, whereas white birch has a whiter color that resembles maple. Both types of birch have a hardness of 4 on a scale of 1 to 5. Birch is readily available and less expensive than many other hardwoods. You can find birch at many home centers, although the selection is better at a lumberyard.
This small coffee table is ideal for a side table or end table. The table is designed with the home handyman in mind. It is both easy to build and is very sturdy. The minimum tools required to construct this coffee table are... Pencil; square; measuring tape; handsaw; hammer; chisel; a couple of clamps and lots of sandpaper. Most handymen are likely to have those tools in their arsenal. Of course... it would make life easier if you also happened to have a drop-saw and a belt sander. The wood used for this coffee table was 90mm x 45mm (1 1/2 x 3 1/2 inches) dressed/surfaced cedar. Cedar is reddish in color, light and easy to work with. Other wood can be used. Virtually any wood can be used for this project, just allow for different widths and thicknesses, and also take into account, the finish. Is the table to be painted, stained and/or coated with polyurethane? Obviously, if the table is to be painted, then an inferior and less expensive wood can be used, as imperfections (within reason) can be filled and painted over.
Having completed this course the learner will be able to: - Describe the history and scope of carpentry as a trade; - Identify the opportunities for carpenters in the construction industry; - Classify the various building materials used by carpenters; - List the most commonly used fasteners and adhesives used by people in the carpentry trade; - Explain the different types of hand and power tools available to carpenters; - Outline the general safety procedures and guidelines that should be followed to operate the tools; - Discuss the importance of employee responsibility and human relations to being successful in the trade; - Identify the various types of construction drawings that make a drawing set; - State the guidelines to read and interpret reading plans and drawings, blueprints, and specifications; - List the various terms associated with floor systems, wall, ceiling and roof framing; - Explain the different methods of framing and constructing houses made of wood; - Describe the types of beams/girders and supports used in construction; - Outline the sequence involved in constructing a platform floor assembly; - Summarize the basic procedure for laying out, assembling, and erecting wood frame walls; - Recognize the different types of roofs used in residential construction; - Determine the length of a common rafter required to construct a roof; - Discuss the terms associated with concrete, concrete reinforcing materials, and formwork; - Apply the concrete mixing information to get different types of concrete, designed to suit various purposes; - Explain the basic concrete curing methods and materials; - List the various components of windows, exterior doors, and stairways used in residential construction; - Summarize the basic installation procedure for pre-hung windows; - State the various types of exterior doors used in residential construction; - Identify the essential requirements for framing stairs; - Describe the design and layout techniques used for stairways and stairwells.

This course introduces students to remodeling practices and demolitions. Students learn how to plan a remodeling project, complete basic plumbing and electrical jobs, apply for permits, match finished materials and estimate costs. Instruction in reading architectural blueprints for residential remodels is generally included, and students become familiar with specifications, codes and construction drawings. Some residential remodeling courses provide hands-on learning experience by requiring group or individual remodeling projects. This course is usually taken after basic carpentry courses.
This is the side table version of the stylish project we shared previously. In certain configurations, it could function as a coffee table. It’s a design suitable for small spaces. The wooden top has this hollow storage compartment which is great for keeping things like a book, a magazine, the remote control or the phone when relaxing on the sofa. The hairpin legs give the table a slender look.
For someone just beginning to purchase hardwood lumber, lumber grades can be overwhelming. Most lumber companies use the generally accepted grading rules set by the National Hardwood Lumber Association. Grades are based on the amount of usable clear material in a board. The highest grade boards are FAS and Select, followed by #1 Common and #2 Common. What grade you choose depends on your project. Some projects, such as tabletops and high quality furniture, may dictate the highest grade available. Many other projects are just as easily adapted to #1 Common (often referred to as cabinet grade) – kitchen cabinet doors, smaller projects and items where some character is acceptable.

Lots of good comments! I do think it is a bit of stretch to include a jointer and surface planner on the ‘basics’ list – we’ve got a slippery slope here! And a lot of different approaches – money, space, time, resources, etc. But lets plunge ahead. If you buy your wood already (or mostly) prep’ed, then the jointer & surface planner can be postponed. You definitely need a way to accurately measure linear distances (e.g. length, width) so a good ruler and tape measure. You need to be able to measure squareness – so you need a good combination square. You need to be able to mark the wood – so a good marking knife, an awl, some chalk, a fine pencil, etc. You should have some decent chisels (and good ones don’t need to cost a lot!). You will need to sharpen them (again not expensive – piece of plate glass and some sandpaper). You need a way to accurately cut your wood – a couple of good handsaws and a file or two for sharpening. You really should have a decent work surface/work bench/etc – a good first project by the way. Last of the basics – a good drill (3/8″ vs battery type). Lastly (I could go on but room is lacking), take a look at Paul Seller’s video’s for simple but highly competent work.


I’d like to add some type of sharpening system to your list. A simple sandpaper and slab system, stones, or the more expensive slow grinder system. Although listed, files should be in this sharpening/maintenance category as well. You’ll need these as soon as you purchase a majority of hand tools. They’ll be needed throughout each day of using the tools. Initial setup and routine maintenance will give better results with less fighting the grain and tool. Whether your a beginner or a master, the tools must be sharp and maintained.
To best engage with designers and architects, Northwest Hardwoods has expanded its social media reach to include Instagram and Pinterest. Both channels are visually based and aspirational, which will allow Northwest Hardwoods to showcase not only its many types of wood grades and species, but also the beautiful and varied applications for these woods – from cabinets to decking to furniture.
The field of carpentry offers many opportunities for employment and advancement for workers with solid educational backgrounds and training. As work and educational experiences enhance your skill sets, you may earn the chance to advance to more responsibility and a higher salary. For example, you could be promoted to a general construction supervisor position within a larger construction company.

Rip your 1x4's so they are 3" wide. This should make them nice and square, so they fit together without any gaps or rounded edges. Drill pocket holes in both ends of each board. Drill several pocket holes (3 or 4) on the edges of each board. Spread wood glue on the edges of each board, and sandwich them together, using bar clamps to keep them tight. Using 1 1/4" pocket hole screws, attach the 1x4's together. (see photo on next step)
Liz Fourez started Love Grows Wild in 2012 with a passion for interior design and homemaking and a dream to help others create a home they love.  From simple project tutorials, to holiday and entertaining ideas, to her journey renovating a 1940’s farmhouse, Liz demonstrates how to create a beautiful and inviting home with a handmade touch. She turned her signature cozy, neutral style into a best-selling book in 2016 and continues to inspire readers with her captivating photography and easy decorating ideas. Read more about Liz > > > >
Training can also offer you the opportunity to specialize in a particular area of this rewarding field, including building maintenance, home renovations, cabinet making, new construction, furniture making, and more. Some programs may even allow you to gain valuable, real-life experience through a paid externship. You'll also learn the latest safety considerations and industry regulations.

To us it is clear: Power, passion and conviction in the process of creation is what drives us and makes us so successful. The common objective is this, both today and for the future, to build the best woodworking machines with respect for our customers and for our environment. This is reinforced with each machine that leaves our factory in Hall in Tirol. 

There are no formal education or training requirements to become a carpenter in the U.S., but the BLS reports that three to four years of experience is the industry standard for becoming a skilled craftsperson. Training and experience can be acquired by working with an experienced journeyman or through an apprenticeship offered by an employer or labor union. Formal in-class instruction is offered through certificate, diploma or associate's degree programs in carpentry at trade or vocational schools. Employees with some formal carpentry education generally start at higher positions in the field. Carpentry courses may include carpentry math, building layouts, foundation work, roofing, stair construction, siding and moldings. You can also study interior and exterior finishes. 

From on-time and on-grade products to an unwavering commitment to its customers, Northwest Hardwoods continues to think ahead and lead with high-quality products and approaches to market. The company announced the launch of its new marketing campaign, Lumber Brings Everything to Life at IWF 2018, which unites its two brands – Northwest Hardwoods and the Industrial Timber and Lumber Company (ITL) brand acquired in 2015 – and illustrates the importance, sustainability and natural beauty that lumber holds in each of our daily lives.
×