The sequence in which boards are cut from a log will determine how stable the boards will be once they dry. As a board loses moisture it will shrink in three dimensions. The change in length is so small as to be considered insignificant and the change in radial movement is always less than the tangential movement. This is most significant as the wood dries between the time it's cut (i.e. green wood), and the point where it is kiln dried or air dried and ready for use. Wood that shrinks excessively, or that has been dried improperly, will often develop checks at the ends. When shopping for lumber, carefully inspect the ends for any checking, or for excessively long checks. It is best to allow for some scrap at the end of each board, just in case. As you trim the end, hit the off-cut across the edge of your bench, and if it breaks in two, you'll have to cut off a little more.

Often referred to as Douglas Fir, this wood has a straight, pronounced grain, and has a reddish brown tint to it. Fir is most often used for building; however, it’s inexpensive and can be used for some furniture-making as well. It doesn’t have the most interesting grain pattern and doesn’t take stain very well, so it’s best to use it only when you intend to paint the finished product. Douglas fir is moderately strong and hard for a softwood, rating 4 on a scale of 1 to 4.

It’s good to know that when it comes to choosing wood to buy that there are somethings that we need to take into consideration. I like how you mentioned that one thing we need to consider is whether we need it to be hard or soft for the project we are needing it for. This is something that we will have to look at and do more research on to make sure that we make the right decision.
Description: In this 6-session class Angela will be guiding as you carve from a pre-roughed blank. (Check in with the store to see which blanks she will have available for this class.) Angela is an experienced, local carver and has designed this class to be fun and creative. This class is run in 6-session increments and may be repeated as needed as it will usually require multiple classes to complete your project.
The first step to building the table is to create the bottom shelf assembly. We used 2×4 boards for this part and ripped the boards to 3” wide each with our table saw. You don’t have to rip your boards on this part, but it will change the overall dimensions, so be sure to make those changes. We made 3/4“ pocket holes around all sides of the plywood panel. We also added 1.5” pocket holes to the ends of each long board. Attach the long sides of the panel to both sides using wood glue and 1.25” pocket hole screws. The plywood for the bottom shelf will be flush with the top of the 2×4 boards.
Screwdrivers are another must-have in the woodworker’s set of hand tools. Not only will you need Phillips and slot, or flathead screwdrivers, you’ll need star drivers and Torx drivers, too. A quality construction is vital to a good set of screwdrivers. So many of them are made out of soft metal, and the first time you put any “oomph” behind them, they strip out, becoming absolutely useless.
Use a nail gun or hammer and finish nails to connect the cross supports to the upper and lower 2×4 side rails. All outside angles are 60 degrees. The two shorter pieces have an inside angle at 30 degrees. The long piece is 22.5″ from outside edge to to inside edge. The 2 shorter pieces are 11 1/4″ from the inside to outer edge. Click here to see a video I made explaining the angles.

Description: In this 6-session class Angela will be guiding as you carve from a pre-roughed blank. (Check in with the store to see which blanks she will have available for this class.) Angela is an experienced, local carver and has designed this class to be fun and creative. This class is run in 6-session increments and may be repeated as needed as it will usually require multiple classes to complete your project.
You’ll need a long screwdriver with a square blade that is very heavy duty. This gives you a lot of torque. You’ll also need a small and medium slot screwdriver. For working on cabinets or tight places in woodworking, you’ll need a screwdriver with a thin shank so that you can reach screws that are inside of deep holes. This is accomplished with a cabinet screwdriver. Get a couple of medium Phillips head screwdrivers, and a stubby one too, for those tight places. You may also want a ratcheting screwdriver.
This woodworking plans project is a Bentwood Coffee Table that is a challenging design for those who would like to try a project which requires wood bending. The contemporary lines combined with traditional natural wood allow this table to fit comforatbly with many other styles of furnishings. The technique for bending the wood does not require any special tools or steaming processes.
Description: Every woodturner enjoys the opportunity to give handmade ornaments to friends and family during the holidays, especially one that is made purely out of wood. No pre-made ornament kits or ornament hardware will be used in this class. One might call it au naturel!!!! During this class you will be given the opportunity to see various ornaments that have been turned on the lathe, ranging from small and simple to large and more decorative. Class objectives include, but are not limited to, the following: Wood choice (more common ornament wood species and pros and cons of each) Discussion and demonstration on how ornaments can be colored using a variety of markers, paints, dyes, and gilder's paste. Discuss and demonstrate how a variety of gouges and tools can be used to make ornaments, including texturing tools. Sharpening techniques - the instructor will assist all students when sharpening tools Ornament rough sketch and design, before the wood is on the lathe. Most important, every student in class will be given the opportunity to turn at least one ornament of their own. The instructor will assist with basic sketch and design, and will rotate among all students to assist with cuts, tool use, technique, sharpening, and helpful hints. Experience level: Beginner (some turning experience highly preferred) Suggested tools: Turning tools will be supplied; however, students are encourage to bring their own tools if they have them. 3/8" or 1/2" spindle gouge, narrow parting tool, and small roughing gouge is a great start. Students who wish to bring their own chuck may do so as well (1"-8 tpi, 2" or 50mm dovetail jaws, and pin jaws). Lunch break from 12:00 to 12:45
These machines are used both in small-scale commercial production of timber products and by hobbyists. Most of these machines may be used on solid timber and on composite products. Machines can be divided into the bigger stationary machines where the machine remains stationary while the material is moved over the machine, and hand-held power tools, where the tool is moved over the material.

Carpentry is one of the most flexible and versatile construction occupations. As a graduate of a carpentry school online, you may work on a wide variety of projects, both indoors and outdoors—from installing kitchen cabinets and drywall to helping construct large-scale projects from the ground up. That versatility is helping to drive job growth: the U.S. Department of Labor expects carpentry careers to grow 8% by 2026.*
I have used a Workmate successfully for years and I am in the process of building an upgraded replacement for the work surfaces. My replacement bench top will be a little longer, much thicker and it will have and extended apron between the two halves to greatly improve holding wood vertically for dovetailing. With this simple upgrade it turns the little Workmate into a very capable portable woodworking bench.
The beverage pallet coffee table is one of the most significant choices for your living room if you live to entertain. It comprises a built-in space for the bucket of the ice storage that possibly keeps your drinks fresh and cold, space which can be tucked away and be covered up when necessary. In this case beverage pallet coffee table is best for you.
I love this & your videos. It’s really helped my confidence level (as a total beginner.) I’ve built your floating shelves (LOVE them) and the cake stand you did (I’m adding dowels in the middle for the connecting parts so I can take it apart & store it almost flat & not worry about Velcro) I’m wondering if you’d do a console that matches this? I really like Ana White’s x console but liked your legs better!

Teak is becoming rarer as the days go on, but it is the staple for fine outdoor furniture. Teak is highly weather-resistant and beautiful (not to mention expensive — can you believe almost $24 a board foot?). Teak has an oily feel and a golden-brown color. It rates a 3 on a scale of 1 to 5 for hardness and is only available from larger lumberyards and specialty suppliers.
This project actually started with me wanting to build a chair for myself, however I lacked advanced woodworking tools and a workshop. I therefore began making furniture that was as straightforward as possible and could be build easily with simple tools. Most importantly, all parts could be cut at the DIY store where I got my plywood. This meant I didn't need a saw bench or lots of space. The cut parts were easy to transport to my home and I could pretty much build the whole chair on the kitchen table. This inspired me to make other furniture pieces in similar fashion. 
×