Rough lumber is sold and measured in ¼" increments; when a board is referred to as 4/4, it means it is four quarters of an inch thick, or one inch. The most common sizes you are likely to encounter at the lumber yard are 4/4 (1"), 6/4 (1½"), 8/4 (2") and 12/4 (3"). Generally, larger dimension lumber is priced per board foot. Price is also dependant upon the wood quality. Boards without blemishes, and of even colour, command higher prices. On most projects it isn't necessary to purchase the best grade material for the entire project. Purchasing a lower grade will allow you to bring home more lumber, and give you the freedom to lay out parts based on appearance rather than waste.

A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.
Dan, I’m worried about you. The stress must be getting to you. Somehow you’ve lost your ability to count. By my estimation, your list has at least 29 items, some of which are actually “sets” of items, like chisels or crayons, which I only counted as one item. Perhaps you need a break from all that blogging, and time to get back to basics, like counting. I can help. Come over to my shop and we can count things like parts, items on the honey-do list, and for extra credit, screw holes. Don’t worry about making mistakes, I’ll guide you through it, and we can round up if necessary. Ha!
This is also a table made from a repurposed pallet. There’s not much you need to change about the pallet, except rearrange a few boards and make the frame smaller. The fact that each board has a slightly different color tone gives the table a special charm. The hairpin legs are a really nice touch. Check out the full tutorial to find out more about how you can build something similar for your own home.

Put an emphasis on the material used in the design of the coffee table. For example, if you’re using wood, showcase its natural beauty, with knots, cracks and all other imperfections. A live edge top would definitely be a good choice in such a case. Check out these rustic coffee table plans to find out all about the steps leading up to a gorgeous and yet simple design.
However, if you want to stain or clear-coat the project, you'll have a number of choices to look through. Since your local home center megamart will probably only carry a couple of hardwood species (poplar and red oak are common) spend time at a fine wood supplier and look through the vareties available. They should be able to help you determine how each species will look when finished, which will go a long way toward refining your decision.
No matter what type of wood working equipment you are looking for, Hermance is here to help. We offer one of the largest selections of general woodworking machinery online. Whether you're in the market for a boring machine, table saw, dust collector, or even an end matcher- you're sure to find what you're looking for in our listings of general woodworking machinery.
The staff of WOODWEB assume no responsibility for the accuracy, content, or outcome of any posting transmitted at WOODWEB's Message Boards. Participants should undertake the use of machinery, materials and methods discussed at WOODWEB's Message Boards after considerate evaluation, and at their own risk. WOODWEB reserves the right to delete any messages it deems inappropriate. (return to top)

Being without machinery to dimension and dress rough timber myself I can definitely see the benefit, but I think the investment (both in money and space) in machinery like this is premature for ‘basic’ woodworking. Additionally, without some other machinery (table saw, bandsaw) you’re still going to have trouble dimensioning smaller timber for projects from large/rough stock (e.g. producing timber strips for case fronts, ripping to reduce thickness, etc).
It's generally more difficult to find long boards. Stock under four or five feet long can often be cut from longer boards, but as the parts become longer, the rough stock will have to be either very clear and straight, or have extra thickness to allow you to remove any bow along its length. In making parts for the room divider (featured in this issue), four stiles had to be set aside: three because they kept bowing no matter how often they were jointed flat, and one because it was under the minimum thickness by the time it was flat.
I’m currently working on a dining room table with this color in mind (I also plan on a coffee table soon). I’ve been testing out stain colors and dark walnut is currently in the lead. I love the way this coffee table turned out in color. How many coats of stain did you use? Also, did the dark wax make a big difference in color? I was planning on using a satin poly for sealant (mostly because it’s what is most convenient and what I’m accustomed to), but I’m interested in the dark wax after seeing this post. Any recommendations you have are much appreciated.

Products and systems by Lamello have always been Products and systems by Lamello have always been designed for longevity and reliability. This legendary durability is combined with environmental stewardship in view as strict environmental regulations at our production site in Switzerland ensure that all resources are used with consideration many of them stemming from sustainable husbandry and management. ...  More + Product Details Close
Hardwoods come from deciduous, or broad-leaved trees, as opposed to softwoods, that are harvested from from evergreens. In general, the lumber derived from hardwood species are typically harder than softwoods, although there are exceptions (balsa wood is very light and soft, but is considered a hardwood). Most hardwood tree species lose their leaves in winter, and generally offer a much wider variety of colors and textures than softwoods. Typically, stock from hardwood species are a lot more expensive than those from softwoods.
Loveland, CO (population: 68,614) has four carpentry schools within a 100-mile radius of its city center. Emily Griffith Opportunity School, the highest ranked school in this group with a carpentry program, has a total student population of 2,230. It is the 2063rd highest ranked school in the USA and the 22nd highest in the state of Colorado (#1 is Colorado College).
Using wood glue and 1 1/4" pocket hole screws, attach the frame you just built (36" x 11") to the 4x4 frame posts. You will use the pocket holes you drilled in the 36" boards. The frame will sit on the edge of the grooves, not inside. See plans for details. The frame should sit flush with the tops of your 4x4's. This will make the bottom 4" off the ground.

This is also a table made from a repurposed pallet. There’s not much you need to change about the pallet, except rearrange a few boards and make the frame smaller. The fact that each board has a slightly different color tone gives the table a special charm. The hairpin legs are a really nice touch. Check out the full tutorial to find out more about how you can build something similar for your own home.


An associate's degree program can be very valuable if your ultimate goals extend to working in management since many leadership roles require a degree credential in a related field. However, if you are more interested in the hands-on aspect of the profession, then a diploma or certificate program can provide the technical knowledge needed to meet the demands of the job.
Moving on to the top of the table. This will be assembled identical to the first shelf assembly, but the depth of the plywood will change. Grab a coupld scraps of the barnwood or planks you are going to use on the top. Lay them flat on a table, and lay the plywood on top of them with the pocket holes facing up. Now attach the long boards first using glue and 1.25” pocket hole screws. After those are attached, you can attach the shorter ends. These will attach with both 3/4 and 2.5” pocket hole screws.
It's generally more difficult to find long boards. Stock under four or five feet long can often be cut from longer boards, but as the parts become longer, the rough stock will have to be either very clear and straight, or have extra thickness to allow you to remove any bow along its length. In making parts for the room divider (featured in this issue), four stiles had to be set aside: three because they kept bowing no matter how often they were jointed flat, and one because it was under the minimum thickness by the time it was flat.
Modern pallet coffee table is simply an enticing choice go with. You can learn how to combine a wooden coffee table in interior design that is modern without creating the impression of bold contrast. You should take steps such as finish the raw pallet accurately, add glass to and set of wheels, coat of fresh paint that is white glossy, and your furniture piece possibly will fit in perfectly.
Rustic furniture look is the hottest furniture look that is chosen to score high value styles and living room fashion trends! So why not get some style-worthy living room coffee table out of some old wood logs? Follow the construction steps and pattern here to get a fab like shown one for good reputation of your living room! Here is the tutorial bhg
It's good practice to purchase all of your lumber for a project at the same time. By doing this, you can acclimatize all the lumber to the same relative humidity level. More importantly, the wood will likely be of a more consistent appearance. Some woods, cherry in particular, can have extreme changes in colour and figure from one tree to the next. Trying to find a few more boards with the same appearance can be an exercise in frustration. The shopping list ensures that you will purchase enough stock for your project the first time.
Table saws help the woodworkers rip, miter, crosscut, and bevel wood. The versatility of the tablesaw is what makes it so useful for the woodworker, making it the workhorse of any woodshop. A tablesaw has a heavy but smooth surface and is made of cast iron to keep it stable. The tablesaw also has two handles: one raises and lowers the blade and the other adjusts angles for the saw. The second handle also enables dust collection.
More than a decade ago I spent 2 weeks in Maine aspiring to learn furniture making. On my return home I started enthusiastically planning to turn my basement into a proper shop – with all the “essential” tools I had learned to use. My list reflected my engineer’s preference for buying quality and quickly exceeded $25k in power tools alone (table saw, band saw, joiner, thickness planer, drill press…) even before solving the power, lighting and dust challenges.
I think it depends on the type of woodworker you would like to become. Are you more interested in traditional “electric free” carpentry or are you drawn to the ease and convenience of modern machinery? Also, I think you should take into consideration what kind and how much shop space you have available. I have worked with all the modern machines for years now, and are just presently finding personal satisfaction in traditional woodworking. In fact, last night I built my very first bookcase with just a few “powerless” hand tools. So in all, I would suggest some personal reflection…What type of woodworker do you want to become?…and from there garnish your shop appropriately. 
×