Disclaimer: Almost any DIY project involves risk of some sort. Your tools, materials, and skills will vary, as will the conditions at your project site. Rogue Engineer has made every effort to be complete and accurate in the instructions provided on this website. Rogue Engineer will not assume any responsibility or liability for damages or losses sustained or incurred in the course of your project or in the use of the item you create. Always follow the manufacturer's operating instructions in the use of tools, check and follow your local building codes, and observe all commonly accepted safety precautions.
Once the mixture is made, simply brush the solution on the wood. It won't immediately turn colors, but over a few hours you'll notice a considerable difference. Check out the photos of my farm table project to see how well it worked using fir boards. You'll notice the fir 2×2's used in this project really took the solution well. The other boards had a little coloring and grain enhancement, but white pine doesn't have many tannins in it so it is less reactive.
Apply glue to the ends of the 1 x 2 End Pieces for the Base and Apron, and then clamp them in place against the inside of the Leg. Position the pieces so that one runs flush with the top edge, and the other sets below the line marked in Step 7. Center both pieces on the leg, and tilt them so that they run parallel to the edge of the Leg. Using a drill/driver and 1¼-inch pocket holes screws, attach the pieces to the Leg. Repeat on the opposite end.

You will perfect your marking, cutting and chiseling skills by making a series of common woodwork joints each joint being that little bit more difficult than the last. These skills will come in for later during the course when you will be required to chop in hinges using a chisel into a door and door frame plus build a door frame with a half lap joint.


Description: This workshop is designed for those who have recently gotten a wood lathe, or have had one for a while, and haven't gotten around to using it until now. During this workshop students get acquainted with the wood lathe and its parts and accessories. We will cover the turning process, as well as sanding and applying finish to a project while it's on the lathe. Students will also be shown a variety of turning tools and how they function. You will also be introduced to wood selection, tool selection, and tool sharpening. Students will test their skills while working on a small turning project. Students should bring suitable eye protection such as safety glasses, goggles, or a face shield. If you have problems with wood dust, a respirator or dust mask would be advisable. Also bring any wood turning tools you might have. Tools and safety gear will be provided for those who don't own them. Materials for turning will be provided.
2 small Japanese pull saws, a western push saw, fret saw, set of chisels, bit brace with a roll of arbor bits, rabbet plane, side rabbet (trim) plane, 2 shoulder planes, 3 set of diamond stones, slip stone, multiple files, a rasp or two, 2 small bar clamps, a mini vise, hand scrapers, scratch beader with cutters, combination plane with cutters, smoothing plane, jack plane, block plane, combination square, steel straight rule, 12′ tape measure, small bottle of glue, a few short dowels, 2 marking gauges, and a few different marking instruments (awl, pencils, marking knife). 

Loveland, CO (population: 68,614) has four carpentry schools within a 100-mile radius of its city center. Emily Griffith Opportunity School, the highest ranked school in this group with a carpentry program, has a total student population of 2,230. It is the 2063rd highest ranked school in the USA and the 22nd highest in the state of Colorado (#1 is Colorado College).
If you have already completed some college or university education, then many apprenticeship programs will give you credit for prior learning. You can even receive credit for work experience you possess in the construction field. It is important to note that any education and work experience credits will likely be evaluated on a case-by-case basis, so if you want to explore this option, then checking around for the best use of your experience is key.
However, if you want to stain or clear-coat the project, you'll have a number of choices to look through. Since your local home center megamart will probably only carry a couple of hardwood species (poplar and red oak are common) spend time at a fine wood supplier and look through the vareties available. They should be able to help you determine how each species will look when finished, which will go a long way toward refining your decision.
I needed a new coffee table for the living room and this design fit the bill perfectly. I came across a table from Ana-White.com that I loved, but modified it a bit because I wanted a breadboard style top. To see her plans click here. The difference between the table in this post is that I cut the top pieces to 41″ (vs 52″) and added the 2×6 pieces to each end, making it come to 52″ with a breadboard style top.
Often referred to as Douglas Fir, this wood has a straight, pronounced grain, and has a reddish brown tint to it. Fir is most often used for building; however, it’s inexpensive and can be used for some furniture-making as well. It doesn’t have the most interesting grain pattern and doesn’t take stain very well, so it’s best to use it only when you intend to paint the finished product. Douglas fir is moderately strong and hard for a softwood, rating 4 on a scale of 1 to 4.
×