Carpentry skills can be applied to residential or commercial remodeling, cabinet making and exterior and interior trim. Coursework in carpentry classes commonly includes instruction in building safety, construction codes, framing and site layout. These courses are widely available at technical schools and colleges. Hands-on practice is emphasized in most classes.
The sequence in which boards are cut from a log will determine how stable the boards will be once they dry. As a board loses moisture it will shrink in three dimensions. The change in length is so small as to be considered insignificant and the change in radial movement is always less than the tangential movement. This is most significant as the wood dries between the time it's cut (i.e. green wood), and the point where it is kiln dried or air dried and ready for use. Wood that shrinks excessively, or that has been dried improperly, will often develop checks at the ends. When shopping for lumber, carefully inspect the ends for any checking, or for excessively long checks. It is best to allow for some scrap at the end of each board, just in case. As you trim the end, hit the off-cut across the edge of your bench, and if it breaks in two, you'll have to cut off a little more.
In this step take your 2×2 rails that are 41″ long and drill  2 pocket holes on each end using a Kreg Jig. Then take 2 1/2 kreg screws and attach the side rails to each 2×4 end piece. Measure 2 1/4 inches up from the bottom to hang your lower 2×2 rail. Note that in the photo my pocket hole screws are pointing inward. The top rail's pocket holes can face inside the table or to the ground. No matter what they won't be seen. Make sure to have the lower rail's pocket holes facing the floor so you'll be able to attach the shelf to them later.

About forty years ago I purchased a Shopsmith Mark V because I lacked space for a large shop, and also moved around the United States a lot. Later I purchased another Shopsmith Mark V Model 510 for the increase in table size and flexibility. I do wood working as a hobby, not to do many projects as fast as possible. I also have every tool and accessory that Shopsmith makes for the two primary tools. Their quality is excellent, and while I enjoy antique tools like the 1912 three phase electric Camel Back Drill Press I purchased for my son’s shop, the Shopsmith does every thing I have ever needed.


Build a career in Carpentry with Alison and learn how to measure, cut, drill, join, fasten, finish and other woodwork skills. The time-honoured trade of carpentry is just as important today as it has ever been. And now, with free, online carpentry courses from Alison, this knowledge can be passed down to digital learning students via the Web. In the Diploma in Carpentry Skills course, you will develop a sound knowledge of the tools, materials and building methods employed in modern carpentry. Other carpentry classes dig deep into the subject of framework and joinery, construction methods and a basic online introduction to carpentry.
The plan I’m using is a modified version of a table from Shabby Creek Cottage, and mine came out to be a whopping 46 1/2″ x 38 1/2″. It’s big, beautiful, and a perfect fit for our space, but if you don’t need a massive table like this one, you can either: make adjustments to these plans OR check out Gina’s table, which is quite a bit smaller. Okay, let’s build!
To cut a 60 degree angle safely I built a jig. I simply nailed 1×4 boards together in a triangle shape. The back 1×4 rests flat on the miter saw fence. You can use the side that runs straight towards you as your new fence. Set the 2×2 board against the fence and slide it into place. Cut the angle at 30 degrees on your miter saw (it will actually cut it at 60 degrees because of your jig.

Wow, what a great problem to have Boris! If you can send some photos I’ll look at them. But unseen, I’d ask them to try to get some quartersawn boards out, and also some full width flatsawn boards. It just depends on how much wood you’ll get if you quartersaw it. It also depends on what you think you’ll build down the road. Some furniture pieces don’t need to be quite as stable as others. Good luck!
Industrial carpenters work on civil engineering projects and in industrial settings, where they build scaffolding and create and set forms for pouring concrete. Some industrial carpenters build tunnel bracing or partitions in underground passageways and mines to control the circulation of air to worksites. Others build concrete forms for tunnels, bridges, dams, power plants, and sewers. 

All graduates keep access to their accounts on the Ashworth EDGE, an online toolkit that provides step-by-step guidance through resume templates, cover letters, thank you letters, and more. As a student, you will interact with the Ashworth EDGE throughout your lessons to make you comfortable with the tools and prepare you to make a good impression on potential employers once you've graduated!
More than a decade ago I spent 2 weeks in Maine aspiring to learn furniture making. On my return home I started enthusiastically planning to turn my basement into a proper shop – with all the “essential” tools I had learned to use. My list reflected my engineer’s preference for buying quality and quickly exceeded $25k in power tools alone (table saw, band saw, joiner, thickness planer, drill press…) even before solving the power, lighting and dust challenges.
This project actually started with me wanting to build a chair for myself, however I lacked advanced woodworking tools and a workshop. I therefore began making furniture that was as straightforward as possible and could be build easily with simple tools. Most importantly, all parts could be cut at the DIY store where I got my plywood. This meant I didn't need a saw bench or lots of space. The cut parts were easy to transport to my home and I could pretty much build the whole chair on the kitchen table. This inspired me to make other furniture pieces in similar fashion.
Furniture Making engages students in the process of furniture making. Topics include an American historical overview and a look at the use of power and hand tools. Common themes include sketchbook work, cutting, hand tools, power tools, bending and jig making. This course employs various technical readings, visual aids, videos, project pictures and assignments.
Even if you are using a beautiful (yet unstable) grain pattern on part of your furniture, it’s a good idea to use stable wood on the other parts. For example, look at an old wooden door. The panels usually have more decorative (less stable) wood, but the rails and stiles (parts of the frame) are usually very stable straight grained wood (don’t worry, I’ll clarify “straight grain” below).
The most commonly purchased claw hammer is the 20 oz. size. It’s heavy enough to easily drive nails but easily manipulated when pulling nails. While wooden handles are picturesque, they may not stand up to the strain if you have to pull a lot of nails. Hammers with a steel handle, or even fiberglass, will be stronger. However, these won’t absorb the vibrations from driving nails the way a hickory handle will. You’ll also need to make sure the fiberglass and metal handles have a rubberized grip for control and comfort. If you’re going to be driving a lot of nails, the wooden handled hammer will be better for reducing stress on your hand, and wrist, too.

When I started planning this makeover, I knew I wanted to get rid of the glass coffee table I had and go with something more rustic and cozy… something with beautiful wood grain that looks like it’s been in an old farmhouse somewhere for ages. So rather than searching every single antique store in town or buying something off the shelf at a big box store, I gathered up my tools, picked up some lumber, and made myself a new coffee table!
Put an emphasis on the material used in the design of the coffee table. For example, if you’re using wood, showcase its natural beauty, with knots, cracks and all other imperfections. A live edge top would definitely be a good choice in such a case. Check out these rustic coffee table plans to find out all about the steps leading up to a gorgeous and yet simple design.
Don’t let the angles on this table scare you away–the design is actually very simple! Just adjust your miter saw from zero to seven degrees for a few of the cuts, and you can create the splayed legs on this basic coffee table. And with the addition of blocks to the front of the legs, it’s easy to fake the look of advanced mortise and tenon joinery. Read on to see how the parts come together.
Always be on the lookout for usable wood. You might be able to salvage some. You can use a metal detector to find nails and screws. You don’t need a full fledged metal detector. I use a pinpointer made by Garrett. If your wood has some woodboring beetles you can still use it if not eaten too badly. A healthy dose of cyfluthrin will take care of them.
Even though this is in fact a side table, we can definitely find inspiration in its design. We find this project to be highly creative and interesting. The table has a hexagon-shaped top and bottom connected by two sets of five rods. Two in each set are longer than the other and go through the bottom hexagon, acting as legs. You can find the plans for this project on ohohblog. 

Carpenters use wood, plastic, fiberglass, drywall, and other materials to build or repair structures and fixtures. Those working for large contracting companies build wooden forms for poured concrete for tunnels, bridges, sewers, and other public projects. Additionally, carpenters install framing for structures, erect scaffolds, build braces in underground passageways and mines, and construct brattices.
With the right tools and materials, what you build is only limited by your imagination and creativity. So why not have a little fun with the kids and teach them something at the same time? Our woodworker tools and woodworking supplies will help you put together an easy birdhouse, squirrel feeder or butterfly house. The kids will love to use our paint samples to add their creative touch, and will enjoy displaying the finished product in the backyard.
The Amish here in Ohio use a nifty wooden rule for calculating bd. ft. It has a brass football shaped hook on the end and they’re about 2′ long. Three columns of numbers run down the length of stick. These columns are the length of stock say, 12,14,16 foot. Within these columns, bd. ft. has already been calculated and marked. For a 16′ bd. the hook is placed over one edge and a reading of bd. ft. is taken from opposite edge from the 16′ column. “Audels Carpenters and Builders Guide #1” pg. 146, shows a good example. They call… Read more »
One of the simplest things you can do is transform a simple wooden pallet into a coffee table. It would be an easy conversion and the result could be similar to this pallet coffee table. Using the boards of the pallet you basically put together the top and the corner and side pieces along with a central support piece. That’s pretty much the whole table and all that’s left to do is add the wheels. So there you have it: your very own pallet coffee table on wheels.
While flipping through the boards, keep an eye open for signs that a number of boards may have come from the same tree. Looking at the ends and the growth rings will tell you where in the log the board was sawn. In some cases, knots may go through more than one board, and often the outer boards have a live edge. By comparing these features, the colouring, grain and other distinguishing marks, it is often possible to identify several boards cut from the same log.

I am finally getting to practice my woodworking more after years of collecting tools. By using tool reviews and thinking of the kind of work I would like to do, I have accumulated a nice set of tools without purchasing many mistakes. I decided to use Paul Sellers book and videos and start learning from the beginning. He starts with projects that begin with a small set of tools. One of those tools is a spokeshave. Even though I know much of what is in the first lessons, I have picked up a few new tricks, and am learning to use my tools more efficiently. My most important tools are my workbench and vise. The workbench was tough to build as I was on the floor using hand planes; not a good way to work. I have no jointer; did get a small planer and made a sled for it so I can flatten a board. My tools are in my house, so there is no room for a big table saw or bandsaw. I have a chopsaw and a piece of an old Craftsman tablesaw I got for free. It has to be moved outside to use. A circular saw with a guide is handy. My guide has a plate on which the saw is mounted. The plate slides on aluminum angle (with help of rollers) which is screwed to plywood. Once the initial cut is made in the plywood, the plywood is simply lined up with your cut marks and clamped down.
The most commonly purchased claw hammer is the 20 oz. size. It’s heavy enough to easily drive nails but easily manipulated when pulling nails. While wooden handles are picturesque, they may not stand up to the strain if you have to pull a lot of nails. Hammers with a steel handle, or even fiberglass, will be stronger. However, these won’t absorb the vibrations from driving nails the way a hickory handle will. You’ll also need to make sure the fiberglass and metal handles have a rubberized grip for control and comfort. If you’re going to be driving a lot of nails, the wooden handled hammer will be better for reducing stress on your hand, and wrist, too.
We really like the distressed look on this coffee table. There are a few ways in which you can achieve that. You can use reclaimed wood or you can create the antiqued finish artificially using special techniques. You can analyze the plans and the instructions shared on instructables to find out more about this strategy. They also show you how to build this stylish pinstripe table.
Loveland lies in Larimer county, which is one of the 55 counties in Colorado. Overall, the Fort Collins-Loveland area has 128,650 total employed workers according to the US Bureau of Labor Statistics, with a 2% unemployment rate, $21/hr average worker wage, and a $43,210 average annual salary. Thus, about 6 out of every 1000 jobs in Loveland are held by carpenters, and 6/1000 are held by construction laborers.
An associate's degree program can be very valuable if your ultimate goals extend to working in management since many leadership roles require a degree credential in a related field. However, if you are more interested in the hands-on aspect of the profession, then a diploma or certificate program can provide the technical knowledge needed to meet the demands of the job.
I’m currently working on a dining room table with this color in mind (I also plan on a coffee table soon). I’ve been testing out stain colors and dark walnut is currently in the lead. I love the way this coffee table turned out in color. How many coats of stain did you use? Also, did the dark wax make a big difference in color? I was planning on using a satin poly for sealant (mostly because it’s what is most convenient and what I’m accustomed to), but I’m interested in the dark wax after seeing this post. Any recommendations you have are much appreciated.
This is the side table version of the stylish project we shared previously. In certain configurations, it could function as a coffee table. It’s a design suitable for small spaces. The wooden top has this hollow storage compartment which is great for keeping things like a book, a magazine, the remote control or the phone when relaxing on the sofa. The hairpin legs give the table a slender look.

Once the mixture is made, simply brush the solution on the wood. It won't immediately turn colors, but over a few hours you'll notice a considerable difference. Check out the photos of my farm table project to see how well it worked using fir boards. You'll notice the fir 2×2's used in this project really took the solution well. The other boards had a little coloring and grain enhancement, but white pine doesn't have many tannins in it so it is less reactive.
11-2. Pipe clamps, I have about 10 of them with varying lengths of black pipe in 1′ increments. I can switch out the clamps for larger lengths on larger projects, or downsize as needed. (very rarely do I need more than 6 clamps on a project during drying time, and when I do, it’s time for a cup of coffee and a 1/2 hour break while I wait) You keep your initial investment down, and buy them as you need them to increase your collection.
In the sixty years of woodworking I have found two tools of increasing necessity. One is a band saw. I can do most of my work with a band saw and hand plane. The second tool is a bow saw, or actually several bow saws. They will replace the band saw if required, though they are slow. One I made about twenty years ago has a one and a half inch wide rip blade and is about thirty inches long. I think the blade is from an old industrial band saw blade I picked up and sharpened into a rip saw blade. It works very well on ripping lumber, logs, etc. Though it tires me out to much to use it now.
A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.
Now that you know how to become a carpenter, you might wonder what the job's like on a day-to-day basis. Because carpentry work demands vigorous exertion, carpenters must be physically fit, strong, and have a good sense of balance. Carpenters must able to work long hours standing, climbing, bending, and kneeling. Additionally, carpenters must be detail-oriented, with good hand-eye coordination and strong problem-solving skills. As carpentry work can be stressful, they must also be able to manage tension and handle workplace pressures. Carpentry work often involves physical risks, like falling and slipping injuries or bruises and cuts from working with sharp tools and rough, heavy materials. Weather conditions and exposure can also pose dangers for carpenters working outdoors.
An associate's degree program can be very valuable if your ultimate goals extend to working in management since many leadership roles require a degree credential in a related field. However, if you are more interested in the hands-on aspect of the profession, then a diploma or certificate program can provide the technical knowledge needed to meet the demands of the job.

Screwdrivers are another must-have in the woodworker’s set of hand tools. Not only will you need Phillips and slot, or flathead screwdrivers, you’ll need star drivers and Torx drivers, too. A quality construction is vital to a good set of screwdrivers. So many of them are made out of soft metal, and the first time you put any “oomph” behind them, they strip out, becoming absolutely useless.


A successful joiner can see the full picture of the project he is preparing to run and for SCM woodworking machinery come to his aid with devices made especially for woodworking machinery; devices that allow to not having to perform the mathematical calculations necessary to make a precise angular cut on a circular saw (with our compex for example) or a template that can produce pieces that are exactly identical among them (on our lathe minimax t 124).
×