Suppose you you were in possession of, as I am, four Cherry logs ranging in size from 18″ to 24″ diameter by 12′ to 16′ in length and you need to instruct the sawmill how they are to be cut. Also suppose that you are a novice woodworker who intends to use the resulting lumber in undetermined woodworking projects. How would you instruct the mill to cut up the logs?
This is a vintage woodworking plan. Visit our FAQ page for a full definition. View the Larger Image Slideshow to see the actual item you are buying. A fine new design just added to our Colonial group is the Wagon Seat Coffee table, patterned in full-size. You will admire its beautiful lines and appreciate its sturdy construction. The well shaped, open gallery and four shelf pegs add to its appearance. Its two drawers are handy for small storage, and the shelves are useful for holding a few magazines or books. Build it of pine or hardwood and finish it with a stain and lacquer of high quality. Then wax it and rub it, and you will have a piece of furniture that will mellow as it improves with time.
The Amish here in Ohio use a nifty wooden rule for calculating bd. ft. It has a brass football shaped hook on the end and they’re about 2′ long. Three columns of numbers run down the length of stick. These columns are the length of stock say, 12,14,16 foot. Within these columns, bd. ft. has already been calculated and marked. For a 16′ bd. the hook is placed over one edge and a reading of bd. ft. is taken from opposite edge from the 16′ column. “Audels Carpenters and Builders Guide #1” pg. 146, shows a good example. They call… Read more »
Description: You've seen him demo in the store, now come join Rod Hendrickson to learn to carve your own realistic animals. Beginners and carvers of all levels are welcome to join this on-going class. First time students will make a miniature duck decoy. Tuition is for 12 hours of class time. Rough cut outs are supplied by the instructor - check with Rod for cost. (approximately $15 for the miniature duck decoy blank)
When I started planning this makeover, I knew I wanted to get rid of the glass coffee table I had and go with something more rustic and cozy… something with beautiful wood grain that looks like it’s been in an old farmhouse somewhere for ages. So rather than searching every single antique store in town or buying something off the shelf at a big box store, I gathered up my tools, picked up some lumber, and made myself a new coffee table!
At Able Skills we pride ourselves in the diversity of the skills that are available within our carpentry training centre. If upon completion of this course you would like to learn much more then you can consider upgrading to City & Guilds Certificate & Training to NVQ Level 2. This would require you to train for an additional 5 weeks; payment would be adjusted to reflect what you have already paid on this course.
It's a little awkward, so we'll get straight to the point: This Wednesday we humbly ask you to defend Wikipedia's independence. We depend on donations averaging about $16.36, but 99% of our readers don't give. If everyone reading this gave $3, we could keep Wikipedia thriving for years to come. The price of your Wednesday coffee is all we need. When we made Wikipedia a non-profit, people warned us we'd regret it. But if Wikipedia became commercial, it would be a great loss to the world. Wikipedia is a place to learn, not a place for advertising. It unites all of us who love knowledge: contributors, readers and the donors who keep us thriving. The heart and soul of Wikipedia is a community of people working to bring you unlimited access to reliable, neutral information. Please take a minute to help us keep Wikipedia growing. Thank you.
An associate's degree program can be very valuable if your ultimate goals extend to working in management since many leadership roles require a degree credential in a related field. However, if you are more interested in the hands-on aspect of the profession, then a diploma or certificate program can provide the technical knowledge needed to meet the demands of the job.

As someone who is just progressing past being a “beginner” (just getting into building furniture) in the woodworking community, I would say there are a number of changes I would make to your list. First, I would say that a power jointer/thicknesser does not belong on the list by any means. They are way too large of an investment and take up a lot of space (not to mention you can buy your stock at the desired dimensions). I also strongly disagree with the concept of joinery devices. As someone new to the trade, I feel this is a very important skill that must be developed, not skipped over by buying devices power devices that achieve a single goal. I think the jigsaw should be replaced by a good bandsaw. I just purchased my first major power tool and it was a 14″ bandsaw and not a tablesaw for space reasons as well as versatility. The bandsaw allows me to resaw, cut curves, (now that it is adjusted for drift) rip pieces of stock accurately that are thicker than a table saw could handle, etc. Once the cut is complete, a handplane can remove any saw marks and square/flatten a surface. It is also really useful for cutting tenons and dovetails. Handsaws can be used for crosscutting and anything else the bandsaw cannot handle. As for a bench, if you are getting into woodworking, this should be your first real project (and it is not expensive to make). You are also missing a good vise to be attached to the bench.

These machines are used both in small-scale commercial production of timber products and by hobbyists. Most of these machines may be used on solid timber and on composite products. Machines can be divided into the bigger stationary machines where the machine remains stationary while the material is moved over the machine, and hand-held power tools, where the tool is moved over the material.
Carpentry students from Loveland schools who go on to become carpenters, construction managers, construction workers, construction engineers, etc. have a good chance at finding employment. For example, there are 743,760 people working as carpenters alone in the US, and their average annual salary is $43,640. Also, Construction laborers make on average $33,190 per year and there are about 856,440 of them employed in the US today. In fact, in the Fort Collins-Loveland area alone, there are 760 employed construction laborers earning an average salary of $29,460. Carpenters in this area earn $39,170/yr and there are 770 employed.
Certain species of wood have traditionally been associated with different styles of furniture. The wood of choice for the Arts & Crafts movement was quarter sawn white oak, valued for its appearance, durability and dimensional stability. An Arts & Crafts style piece executed in maple might be a well-made example of a classic style, but the choice of wood would be visually at odds with the design. Pine and other softwoods impart a more relaxed, country influence, while traditional hardwoods, such as cherry and walnut, are more likely to be associated with fine furniture.
Description: Now that you have your new lathe tools, come join us to learn how to sharpen your chisels so that you can get the best performance from your equipment. You will be taught several different methods that can be used to keep your tools sharp and effective. You will be learning how to sharpen all of the basic lathe tools. This is a "must have" class for beginning woodturners.
The Delta 22-555 Portable Thickness Planer is great The Delta 22-555 Portable Thickness Planer is great for professional results in the woodworker's shop. It features two polyurethane feed rollers for a no-slip grip on the work piece; positioned close to the cutter head to improve work piece finish. The machine also has precision machined steel cutter head for ...  More + Product Details Close
One name rang out like a bell at multiple forums, from many different woodworkers: Steve Wall Lumber. From what we read (NOT direct experience!) it looks like the only way you can go wrong with Wall Lumber is if they don’t have what you’re looking for. The other frequently-cited lumber sellers are worth looking into for sure, as it’s always good to have multiple sources!

This project actually started with me wanting to build a chair for myself, however I lacked advanced woodworking tools and a workshop. I therefore began making furniture that was as straightforward as possible and could be build easily with simple tools. Most importantly, all parts could be cut at the DIY store where I got my plywood. This meant I didn't need a saw bench or lots of space. The cut parts were easy to transport to my home and I could pretty much build the whole chair on the kitchen table. This inspired me to make other furniture pieces in similar fashion.

×