At Able Skills we pride ourselves in the diversity of the skills that are available within our carpentry training centre. If upon completion of this course you would like to learn much more then you can consider upgrading to City & Guilds Certificate & Training to NVQ Level 2. This would require you to train for an additional 5 weeks; payment would be adjusted to reflect what you have already paid on this course.

Description: In this 6-session class Angela will be guiding as you carve from a pre-roughed blank. (Check in with the store to see which blanks she will have available for this class.) Angela is an experienced, local carver and has designed this class to be fun and creative. This class is run in 6-session increments and may be repeated as needed as it will usually require multiple classes to complete your project.


Carpentry is one of the most flexible and versatile construction occupations. As a graduate of a carpentry school online, you may work on a wide variety of projects, both indoors and outdoors—from installing kitchen cabinets and drywall to helping construct large-scale projects from the ground up. That versatility is helping to drive job growth: the U.S. Department of Labor expects carpentry careers to grow 8% by 2026.*
First, build two boxes for each leg assembly. These are attached using wood glue and 2.5” pocket hole screws through the horizontal boards and into the vertical boards.  You want your pocket holes facing the outside of the box on this part because we will cover them with another board on the next part.  We used our K5 Kreg Jig for this part.  We get asked ALL the time which Kreg Jig to start with.  We always suggest the K5.  We use it on almost every build.  You can find it HERE on Amazon!
First, build two boxes for each leg assembly. These are attached using wood glue and 2.5” pocket hole screws through the horizontal boards and into the vertical boards.  You want your pocket holes facing the outside of the box on this part because we will cover them with another board on the next part.  We used our K5 Kreg Jig for this part.  We get asked ALL the time which Kreg Jig to start with.  We always suggest the K5.  We use it on almost every build.  You can find it HERE on Amazon!

The staff of WOODWEB assume no responsibility for the accuracy, content, or outcome of any posting transmitted at WOODWEB's Message Boards. Participants should undertake the use of machinery, materials and methods discussed at WOODWEB's Message Boards after considerate evaluation, and at their own risk. WOODWEB reserves the right to delete any messages it deems inappropriate. (return to top)

The course begins with a quick overview of the history of carpentry, from primitive to modern times. It then teaches you about the most important building materials, fasteners, adhesives, and tools used by carpenters in the modern construction industry. You will then receive an essential outline of safety guidelines and procedures. The course then goes through the crucial steps carpenters must take during construction projects. Here, you will be introduced to the best methods for constructing floor systems, walls, and roof framing, as well as how to make and read plans and elevations. The final section of the course shows you how to close off a structure, including installing windows, exterior doors, and stairs.
Before I send you over there, I have two favors to ask of you. First, help us continue to improve the map! This is not a map of every lumberyard, but if you have a local favorite that isn’t listed, please send it along, with your name and a short blurb about why you like the yard. You can email me the listings at [email protected]. A note – if you are an owner or employee of the yard, please indicate that when you submit. I’m not against someone making a case for his or her operation, but I’d like to note it in your blurb. This isn’t a space to advertise your business, it’s a community resource for other woodworkers. I do look at every entry, which is part of why it took this long to get the map together!
Commercial carpenters build and remodel commercial office buildings, hospitals, hotels, schools, and shopping malls. Some specialize in light-gauge and load-bearing steel framing for interior partitions, exterior framing, and curtain wall construction. Others specialize in concrete forming systems and finishing interior and exterior walls, partitions, and ceilings.

The last step is to dry brush over top of the white washed surface. Using a dry brush, I used the same linen white chalk paint from Rust-Oleum and dipped the tip of the brush into the paint. Getting just a little paint on the end of the brush, I then dabbed the brush onto a piece of scrap wood to take off any excess paint. Then, going with the grain of the wood, I used quick strokes. You can add more or less depending on the look you desire!
“The earliest credible evidence of coffee-drinking appears in the middle of the 15th century in the Sufi shrines of Yemen. It was here in Arabia that coffee seeds were first roasted and brewed, in a similar way to how it is now prepared. Coffee seeds were first exported from Eastern Africa to Yemen, as the coffee plant is thought to have been indigenous to the former.Yemeni traders took coffee back to their homeland and began to cultivate the seed. By the 16th century, it had reached the rest of the Middle East, Persia, Turkey, and northern Africa. From there, it spread to Europe and the rest of the world.” [source]

The sequence in which boards are cut from a log will determine how stable the boards will be once they dry. As a board loses moisture it will shrink in three dimensions. The change in length is so small as to be considered insignificant and the change in radial movement is always less than the tangential movement. This is most significant as the wood dries between the time it's cut (i.e. green wood), and the point where it is kiln dried or air dried and ready for use. Wood that shrinks excessively, or that has been dried improperly, will often develop checks at the ends. When shopping for lumber, carefully inspect the ends for any checking, or for excessively long checks. It is best to allow for some scrap at the end of each board, just in case. As you trim the end, hit the off-cut across the edge of your bench, and if it breaks in two, you'll have to cut off a little more.
The staff of WOODWEB assume no responsibility for the accuracy, content, or outcome of any posting transmitted at WOODWEB's Message Boards. Participants should undertake the use of machinery, materials and methods discussed at WOODWEB's Message Boards after considerate evaluation, and at their own risk. WOODWEB reserves the right to delete any messages it deems inappropriate. (return to top)
In addition to the type of finish you want, the location of the final installation should be considered when choosing a hardwood species. While it won't have as much bearing on furniture pieces to be used indoors, you may want to consider some more moisture-resistant species (such as cypress or the ever-increasingly endangered teak) for outdoor projects. Again, your local woodworking supplier will be able to help with this decision if you are unsure about what species might work well for your particular application and climate.
Additionally, working with a contractor or construction company allows students to gain hands-on experience that's virtually imperative for future employment. High school graduates may advance to apprenticeship, vocational, or technical programs. Generally, training to become a skilled carpenter requires 3-4 years of on-the-job instruction and formal education (either in person or through online carpenter school).
I built my coffee table!! I used the plans at www. EasyWoodwork.org to build mine – highly recommended you check those out too. They are detailed and super easy to read and understand unlike several others I found online. The amount of plans there is mind-boggling… there’s like 16,000 plans or something like that for tons of different projects. Definitely enough to keep me busy with projects for many more years to come haha
Using wood glue and 1 1/4" pocket hole screws, attach the frame you just built (36" x 11") to the 4x4 frame posts. You will use the pocket holes you drilled in the 36" boards. The frame will sit on the edge of the grooves, not inside. See plans for details. The frame should sit flush with the tops of your 4x4's. This will make the bottom 4" off the ground.

We are all well aware of the role of a DIY coffee table for a living room which is highly versatile! It is what you need to get first while entertaining some visitors or guests in the living room! The conversations are also to start always by sitting around it! It is seen mostly in the center of the sitting plans! The reason is that all the sitting personages can use it to place their mobile phones, cups, beverage mugs, magazines and other materials over it while they need to get their hands free for the detailed conversations! So this all tells that how utilitarian item a coffee is!
Using wood glue and 1 1/4" pocket hole screws, attach the frame you just built (19" x 11") to the 4x4 frame posts. You will use the pocket holes you drilled in the 19" boards. The frame will sit on the edge of the grooves, not inside. See plans for details. The frame should sit flush with the tops of your 4x4's. This will make the bottom 4" off the ground. 
×