Rough lumber is sold and measured in ¼" increments; when a board is referred to as 4/4, it means it is four quarters of an inch thick, or one inch. The most common sizes you are likely to encounter at the lumber yard are 4/4 (1"), 6/4 (1½"), 8/4 (2") and 12/4 (3"). Generally, larger dimension lumber is priced per board foot. Price is also dependant upon the wood quality. Boards without blemishes, and of even colour, command higher prices. On most projects it isn't necessary to purchase the best grade material for the entire project. Purchasing a lower grade will allow you to bring home more lumber, and give you the freedom to lay out parts based on appearance rather than waste.
While flipping through the boards, keep an eye open for signs that a number of boards may have come from the same tree. Looking at the ends and the growth rings will tell you where in the log the board was sawn. In some cases, knots may go through more than one board, and often the outer boards have a live edge. By comparing these features, the colouring, grain and other distinguishing marks, it is often possible to identify several boards cut from the same log.
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience. 
Description: Now that you have your new lathe tools, come join us to learn how to sharpen your chisels so that you can get the best performance from your equipment. You will be taught several different methods that can be used to keep your tools sharp and effective. You will be learning how to sharpen all of the basic lathe tools. This is a "must have" class for beginning woodturners.
Dan, my work space that is available for power tools is quite small, about 6′ x 20′. It may seem like a lot on the surface, but a long rectangle is a bear to work in. It requires a lot of serpentine action. That said, I don’t have too much room for large footprint tools. I have settled finally on three big tools; a small bench saw, a thickness planer, and a drill press. I had to forgo the jointer, so I use hand tools to make up for it’s absence (as I do with a lot of my hand tool techniques). I have gotten to the point where I can flatten one side and true an edge of a board reasonably quick. I then finish it up with the thickness planer and table saw, giving me a nice flat board. I guess what I am basically saying is, there’s more than one way to skin a cat, and don’t write off hand tools as a quaint way to experience the past. They worked for thousands of years, and still do! Thanks for the blogs, they make for great reading.
Now, I know this list only contains traditional hand tools, but my circumstances led me to this choice to complete the job. After all, he is my brother and he’s helped me once or twice. Not all woodworkers will want to take the time and effort to go strictly with hand tools. That’s fine; different circumstances and preferences will lead the way. Most people wouldn’t drive a scooter full of tools to assist their siblings either. Sounds crazy, but I enjoyed the trip through the mountains. Once I was there, I still needed a way to rip through lumber. I also needed a can of finish. As needed, a few jigs and templates were constructed from the purchased lumber.
Convert your Delta Midi-Lathe to a full size Convert your Delta Midi-Lathe to a full size lathe by adding the Delta Midi Lathe Bed Extension. Featuring a modular design so you can connect multiple extensions this extension increases bed length by 25-1/2 in. so you can turn longer spindles. To reduce vibration add 34 lbs. of cast iron ...  More + Product Details Close
I work with a lot of rough sawn boards (Wood Mizer) that are up to 12 inches wide. The worse defect is twist. First I saw the stock to rough project lengths and then using winding sticks, I attack the twist with a #5 hand plane, gradually moving the winding sticks toward the center. If there is bow or cup I can plane that out also. I now have a reference surface that can go thru my planer. The finished boards are perfect. This is not really difficult or excessively time consuming.

After you've used one of these free coffee table plans to build your dream coffee table, check out these other free woodworking plans for bookcases, TV stands, dressers, nightstands, step stools, entertainment centers, farmhouse tables, desks, jewelry boxes, dining room tables, wine racks, picnic tables, kitchen islands, home bars, bunk beds, toy boxes, and even dog houses.

Additionally, after becoming a journey level carpenter, you can go on to obtain master certification, which typically requires multiple years of consecutive experience as a journeyworker. This can help you earn a higher wage or qualify for teaching or management roles. You can even take on your own apprentices, allowing you to share your expertise with the next generation of professionals.
Maple comes in two varieties: hard and soft. Both varieties are harder than many other woods; hard maple is so hard (a 5 on a scale of 1 to 5) that it’s difficult to work with. Soft maple, on the other hand, is relatively easy to work with. Because of their fine, straight grain, both varieties are more stable than many other woods. They also tend to be less expensive than other hardwoods. You won’t find maple at your local home center, but most lumberyards have a good selection of it.
I love this & your videos. It’s really helped my confidence level (as a total beginner.) I’ve built your floating shelves (LOVE them) and the cake stand you did (I’m adding dowels in the middle for the connecting parts so I can take it apart & store it almost flat & not worry about Velcro) I’m wondering if you’d do a console that matches this? I really like Ana White’s x console but liked your legs better!
My $0.02 worth. I agree with the thickness planer [mine is 10″] but anything over a 6″ jointer is expensive and space-consuming, so use hand planes as in your later blog. I inherited an 8″ table saw that my dad and I used to build a 12′ outboard boat back in 1955. I’ve used it for ripping, but I’m having second thoughts because of safety issues. Some have suggested a band saw for ripping, which is quieter and safer to use. I gave my router away [and hope to get rid of my Freud biscuit joiner and 6″ jointer]. A quality eggbeater drill works every bit [pun not intended] as well as a power drill, and they cost less. A coping saw and a jewelers saw negate the need for a jigsaw unless you are into making puzzles. Chris Schwarz has a video short on one of the Highland Woodworker series showing how to joint the edge of a board with a plane and a simple jig on the workbench surface. Another reason to bypass the jointer.
1: Table saw in place of a jointer. Any number of tips in previous issues address straightening edges of boards without a jointer. A jointer serves one purpose, but a tablesaw can serve many (just watch your local Craigslist for a decent one to come up.) The thickness planer is unavoidable, but until you can afford one, buy stock in the thickness you need.
If creating the coffee table precedes the actual design phase of your interior space, take into consideration future positioning, size and functionality that will determine the addition of storage space.Personalize each piece created from the free coffee table plans featured above and claim it your own. Choose a fun bright tone or paint it Scandinavian white for a calming relaxing effect.Simply fallow the tutorials above and design your perfect coffee table today.
“Basic,” on the other hand, is a word that allows for growth – and that’s exactly what you want in your woodworking tool kit. You want to be able to take the same kit with you through many years in the craft. With my basic woodworking tools list, I wanted to provide a core set of tools that will serve you well from project to project. I’m especially concerned these days with the transition to hardwood furniture making, as opposed to plywood boxes of various sizes. That’s the transition I’m making right now in my own work!
In the sixty years of woodworking I have found two tools of increasing necessity. One is a band saw. I can do most of my work with a band saw and hand plane. The second tool is a bow saw, or actually several bow saws. They will replace the band saw if required, though they are slow. One I made about twenty years ago has a one and a half inch wide rip blade and is about thirty inches long. I think the blade is from an old industrial band saw blade I picked up and sharpened into a rip saw blade. It works very well on ripping lumber, logs, etc. Though it tires me out to much to use it now.
×