Having completed this course the learner will be able to: - Describe the history and scope of carpentry as a trade; - Identify the opportunities for carpenters in the construction industry; - Classify the various building materials used by carpenters; - List the most commonly used fasteners and adhesives used by people in the carpentry trade; - Explain the different types of hand and power tools available to carpenters; - Outline the general safety procedures and guidelines that should be followed to operate the tools; - Discuss the importance of employee responsibility and human relations to being successful in the trade; - Identify the various types of construction drawings that make a drawing set; - State the guidelines to read and interpret reading plans and drawings, blueprints, and specifications; - List the various terms associated with floor systems, wall, ceiling and roof framing; - Explain the different methods of framing and constructing houses made of wood; - Describe the types of beams/girders and supports used in construction; - Outline the sequence involved in constructing a platform floor assembly; - Summarize the basic procedure for laying out, assembling, and erecting wood frame walls; - Recognize the different types of roofs used in residential construction; - Determine the length of a common rafter required to construct a roof; - Discuss the terms associated with concrete, concrete reinforcing materials, and formwork; - Apply the concrete mixing information to get different types of concrete, designed to suit various purposes; - Explain the basic concrete curing methods and materials; - List the various components of windows, exterior doors, and stairways used in residential construction; - Summarize the basic installation procedure for pre-hung windows; - State the various types of exterior doors used in residential construction; - Identify the essential requirements for framing stairs; - Describe the design and layout techniques used for stairways and stairwells.
The last step is to dry brush over top of the white washed surface. Using a dry brush, I used the same linen white chalk paint from Rust-Oleum and dipped the tip of the brush into the paint. Getting just a little paint on the end of the brush, I then dabbed the brush onto a piece of scrap wood to take off any excess paint. Then, going with the grain of the wood, I used quick strokes. You can add more or less depending on the look you desire!
I am finally getting to practice my woodworking more after years of collecting tools. By using tool reviews and thinking of the kind of work I would like to do, I have accumulated a nice set of tools without purchasing many mistakes. I decided to use Paul Sellers book and videos and start learning from the beginning. He starts with projects that begin with a small set of tools. One of those tools is a spokeshave. Even though I know much of what is in the first lessons, I have picked up a few new tricks, and am learning to use my tools more efficiently. My most important tools are my workbench and vise. The workbench was tough to build as I was on the floor using hand planes; not a good way to work. I have no jointer; did get a small planer and made a sled for it so I can flatten a board. My tools are in my house, so there is no room for a big table saw or bandsaw. I have a chopsaw and a piece of an old Craftsman tablesaw I got for free. It has to be moved outside to use. A circular saw with a guide is handy. My guide has a plate on which the saw is mounted. The plate slides on aluminum angle (with help of rollers) which is screwed to plywood. Once the initial cut is made in the plywood, the plywood is simply lined up with your cut marks and clamped down.
Apply glue to the ends of the 1 x 2 End Pieces for the Base and Apron, and then clamp them in place against the inside of the Leg. Position the pieces so that one runs flush with the top edge, and the other sets below the line marked in Step 7. Center both pieces on the leg, and tilt them so that they run parallel to the edge of the Leg. Using a drill/driver and 1¼-inch pocket holes screws, attach the pieces to the Leg. Repeat on the opposite end.
Suppose you you were in possession of, as I am, four Cherry logs ranging in size from 18″ to 24″ diameter by 12′ to 16′ in length and you need to instruct the sawmill how they are to be cut. Also suppose that you are a novice woodworker who intends to use the resulting lumber in undetermined woodworking projects. How would you instruct the mill to cut up the logs?
Just a little nitpick on the tape measure blurb. The hook should not be completely tight. It should move in and out about a 1/16th or the thickness of the hook. This way you get an accurate measurement whether you hook a part to measure or bump up to it. If you want more accurate measurements with a tape measure, “burn” an inch instead of hooking or bumping the part. Just line up what you want to measure with the 1″ mark and subtract that inch from the final measurement.
Scm specializes in designing and manufacturing woodworking machines and services for joineries and customized production shops working with melamine panels, solid wood and other plastic materials. All machines are configured to offer the best technological innovations, high performance and reliability. Easy to install and easy to use, Scm products are distributed all over the world. 
It all depends on the program. Some programs are designed for those already working in the construction industry. Other programs are open to anyone, regardless of their background. Some classes have a specific date by which you must have all of your work completed. Others impose no time limits and give you an unlimited timeframe to complete your work.
Rustic furniture look is the hottest furniture look that is chosen to score high value styles and living room fashion trends! So why not get some style-worthy living room coffee table out of some old wood logs? Follow the construction steps and pattern here to get a fab like shown one for good reputation of your living room! Here is the tutorial bhg
If you can buy a bunch of tools at one time, you can save a ton on shipping, as the more you buy, the lower the rates. Also, take advantage of free shipping offers. Compare to see where you can get the best deal. Whatever you buy, make sure it is high quality. I have a Nicholson backsaw I bought at a local store before I knew of the woodworking suppliers. It has never been used much, but cuts much slower than saws such as Gramercy or Lie-Nielsen, even though mine have smaller teeth than the Nicholson.

Even if you are using a beautiful (yet unstable) grain pattern on part of your furniture, it’s a good idea to use stable wood on the other parts. For example, look at an old wooden door. The panels usually have more decorative (less stable) wood, but the rails and stiles (parts of the frame) are usually very stable straight grained wood (don’t worry, I’ll clarify “straight grain” below).
“Basic,” on the other hand, is a word that allows for growth – and that’s exactly what you want in your woodworking tool kit. You want to be able to take the same kit with you through many years in the craft. With my basic woodworking tools list, I wanted to provide a core set of tools that will serve you well from project to project. I’m especially concerned these days with the transition to hardwood furniture making, as opposed to plywood boxes of various sizes. That’s the transition I’m making right now in my own work!
×