No matter what type of wood working equipment you are looking for, Hermance is here to help. We offer one of the largest selections of general woodworking machinery online. Whether you're in the market for a boring machine, table saw, dust collector, or even an end matcher- you're sure to find what you're looking for in our listings of general woodworking machinery.
Lots of good comments! I do think it is a bit of stretch to include a jointer and surface planner on the ‘basics’ list – we’ve got a slippery slope here! And a lot of different approaches – money, space, time, resources, etc. But lets plunge ahead. If you buy your wood already (or mostly) prep’ed, then the jointer & surface planner can be postponed. You definitely need a way to accurately measure linear distances (e.g. length, width) so a good ruler and tape measure. You need to be able to measure squareness – so you need a good combination square. You need to be able to mark the wood – so a good marking knife, an awl, some chalk, a fine pencil, etc. You should have some decent chisels (and good ones don’t need to cost a lot!). You will need to sharpen them (again not expensive – piece of plate glass and some sandpaper). You need a way to accurately cut your wood – a couple of good handsaws and a file or two for sharpening. You really should have a decent work surface/work bench/etc – a good first project by the way. Last of the basics – a good drill (3/8″ vs battery type). Lastly (I could go on but room is lacking), take a look at Paul Seller’s video’s for simple but highly competent work.
The owners, webmasters, administrators, authors and editors, expressly disclaim all and any liability to any person, whether a user of this website or not, in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance, whether whole or partial, upon the whole or any part of the contents of this website. Please exercise caution when working with any tools or machinery. Follow common safety rules and precautions as outlined in any manuals related to the equipment being used. If advice or other expert assistance is required, the services of a competent professional person should be sought.
Integrating a planter into a table is actually a pretty common idea. We’ve seen quite a few projects which include this feature and one of them comes from abeautifulmess. Check out the plans to find out how to put together with a minimalist and stylish coffee table with a planter at its center. You can use that space as a herb garden or you can plant grass or succulents in there. We really the crisp and linear design, the pureness of the white body and the strong contrast with the black legs and the green of the plants. It’s refreshing in a very special way.

Treeline offers only the finest wood carving tools and supplies. Everything from Treeline is backed by our 30-day guarantee against any defects. We have been providing wood carving tools since 1997 and we strive to excel in customer service and quality products. All employees at Treeline are very knowledgeable and professional, so if you are looking for the right woodcarving tools, contact us and we will do our best to help you.
Use a polyurathane ( I used a Minwax Semi-Gloss ) to seal and protect the finished coffee table. Apply the 1st coat of polyurethane to the entire table. Once dry, add a second coat to the table top. I only generally do one coat of poly on the base. Once the second coat has dried take a sanding block with 400 grit sandpaper and lightly sand all areas you've poly'ed. Then take a clean damp rag to remove the dust and prepare for your final coat of poly.
The coffee table is most often the furniture piece which sits at the very heart of spaces such as the living room, outdoor lounge or pretty much any sitting area no matter the size or style. In these conditions, the coffee table is a focal point for that space and takes on a very special role. It’s often the piece which ties together the whole decor around it. There are, naturally, lots of possible designs and looks for such an element so we’ve prepared a set of inspiring coffee table plans which you might find useful if you’re ever interested in building your own furniture.
If you have ever thought of building something from all those wooden pallets you see laying around, well take a look at what Norm put together in this coffee table. Rustic indeed, no two tables will look alike. The purpose of this project is to demonstrate the techniques needed to build such a project and how to work with the material. View the Larger Image Slideshow to see the actual paper plan you are buying.
Chic white coffee table with blag legs and with amazing natural garden like spell! This happens due to built-in planter that make you feel like you are sitting in a garden while being around this coffee table! Grow your favorite flowers or herbs in the integrated planter or simply use it as an ice box for your beverage parties! Want to copy this versatile table design now? Step-by-step DIY tutorial here abeautifulmess

Home Site Map What's New New Visitors Video Library Software & Mobile Apps Auctions, Sales and Special Offers Industry News Woodworkers Directory Sawing and Drying Directory The Wood Doctor Bookstore Lumber Buying Guide Tradeshow Directory Newsstand Lumber/Timber/Misc Calculators Events Calendar Media Kit Poll Center About WOODWEB What Our Visitors Say Frequently Asked Questions Contact WOODWEB User Agreement and Terms of Use Privacy Policy Link to WOODWEB Refer a Friend Subscribe to the WOODWEB Update Update Archive Become a Member


I am finally getting to practice my woodworking more after years of collecting tools. By using tool reviews and thinking of the kind of work I would like to do, I have accumulated a nice set of tools without purchasing many mistakes. I decided to use Paul Sellers book and videos and start learning from the beginning. He starts with projects that begin with a small set of tools. One of those tools is a spokeshave. Even though I know much of what is in the first lessons, I have picked up a few new tricks, and am learning to use my tools more efficiently. My most important tools are my workbench and vise. The workbench was tough to build as I was on the floor using hand planes; not a good way to work. I have no jointer; did get a small planer and made a sled for it so I can flatten a board. My tools are in my house, so there is no room for a big table saw or bandsaw. I have a chopsaw and a piece of an old Craftsman tablesaw I got for free. It has to be moved outside to use. A circular saw with a guide is handy. My guide has a plate on which the saw is mounted. The plate slides on aluminum angle (with help of rollers) which is screwed to plywood. Once the initial cut is made in the plywood, the plywood is simply lined up with your cut marks and clamped down.
Whether you are a beginner or a DIY professional, if you have a love for the craft of woodworking The Home Depot has got you covered. We have all the essential tools for woodworking that let you hone your craft. Our huge selection of drill presses and miter saws will put the power in your hands to complete your projects faster and easier. And whether you are looking for the strength of a powerful router or the versatility of a lathe, you can find everything you need to help with projects, large and small. If your carpentry plans also include building materials, you don't need to look any further than The Home Depot. From wood and lumber to decking and fencing materials, it's all right here.
If you have already completed some college or university education, then many apprenticeship programs will give you credit for prior learning. You can even receive credit for work experience you possess in the construction field. It is important to note that any education and work experience credits will likely be evaluated on a case-by-case basis, so if you want to explore this option, then checking around for the best use of your experience is key.

Most chisels are beveled on the 2 sides and on the cutting edge, but specialty chisels may only be beveled at the cutting edge. This bevel will be at 20 to 25 degrees down the length of the blade on one side, and flat on the backside. The blade will be between 4” and 7” long. Make sure you get chisels with a grip that fits your hand. If the grip is too small, you won’t be able to hold the chisel steady as you work. Be sure to use a mallet or wood hammer when you work, so that you don’t destroy the head on your chisel. Keep track of the edge caps, keep them sharp, and oil the metal now and then after you’ve used them, and they should be good for years. If you don’t have the edge caps, get a roll to keep them in. This will prevent them from bouncing around in your tool box drawers and getting damaged.

Congrats! You've finished your coffee-table. If you liked building it and are happy with the result you can find other similar designs at www.screwed-up.com. If you want to know what's going on with Screwed-Up you can join the facebook page (https://www.facebook.com/Screwed-Up-2092172627662047/), or maybe you want to follow me on pinterest (https://nl.pinterest.com/screwedupdiyfurniture/pins/). For finishing touches I recommend sanding the edges and corners smooth. Also treating the top with a (clear) wood finish to protect against spills is never a bad idea.


Dan, my work space that is available for power tools is quite small, about 6′ x 20′. It may seem like a lot on the surface, but a long rectangle is a bear to work in. It requires a lot of serpentine action. That said, I don’t have too much room for large footprint tools. I have settled finally on three big tools; a small bench saw, a thickness planer, and a drill press. I had to forgo the jointer, so I use hand tools to make up for it’s absence (as I do with a lot of my hand tool techniques). I have gotten to the point where I can flatten one side and true an edge of a board reasonably quick. I then finish it up with the thickness planer and table saw, giving me a nice flat board. I guess what I am basically saying is, there’s more than one way to skin a cat, and don’t write off hand tools as a quaint way to experience the past. They worked for thousands of years, and still do! Thanks for the blogs, they make for great reading.
Most chisels are beveled on the 2 sides and on the cutting edge, but specialty chisels may only be beveled at the cutting edge. This bevel will be at 20 to 25 degrees down the length of the blade on one side, and flat on the backside. The blade will be between 4” and 7” long. Make sure you get chisels with a grip that fits your hand. If the grip is too small, you won’t be able to hold the chisel steady as you work. Be sure to use a mallet or wood hammer when you work, so that you don’t destroy the head on your chisel. Keep track of the edge caps, keep them sharp, and oil the metal now and then after you’ve used them, and they should be good for years. If you don’t have the edge caps, get a roll to keep them in. This will prevent them from bouncing around in your tool box drawers and getting damaged.
There are no formal education or training requirements to become a carpenter in the U.S., but the BLS reports that three to four years of experience is the industry standard for becoming a skilled craftsperson. Training and experience can be acquired by working with an experienced journeyman or through an apprenticeship offered by an employer or labor union. Formal in-class instruction is offered through certificate, diploma or associate's degree programs in carpentry at trade or vocational schools. Employees with some formal carpentry education generally start at higher positions in the field. Carpentry courses may include carpentry math, building layouts, foundation work, roofing, stair construction, siding and moldings. You can also study interior and exterior finishes.
Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck!
The owners, webmasters, administrators, authors and editors, expressly disclaim all and any liability to any person, whether a user of this website or not, in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance, whether whole or partial, upon the whole or any part of the contents of this website. Please exercise caution when working with any tools or machinery. Follow common safety rules and precautions as outlined in any manuals related to the equipment being used. If advice or other expert assistance is required, the services of a competent professional person should be sought.
This project actually started with me wanting to build a chair for myself, however I lacked advanced woodworking tools and a workshop. I therefore began making furniture that was as straightforward as possible and could be build easily with simple tools. Most importantly, all parts could be cut at the DIY store where I got my plywood. This meant I didn't need a saw bench or lots of space. The cut parts were easy to transport to my home and I could pretty much build the whole chair on the kitchen table. This inspired me to make other furniture pieces in similar fashion.
×