Description: This workshop is designed for those who have recently gotten a wood lathe, or have had one for a while, and haven't gotten around to using it until now. During this workshop students get acquainted with the wood lathe and its parts and accessories. We will cover the turning process, as well as sanding and applying finish to a project while it's on the lathe. Students will also be shown a variety of turning tools and how they function. You will also be introduced to wood selection, tool selection, and tool sharpening. Students will test their skills while working on a small turning project. Students should bring suitable eye protection such as safety glasses, goggles, or a face shield. If you have problems with wood dust, a respirator or dust mask would be advisable. Also bring any wood turning tools you might have. Tools and safety gear will be provided for those who don't own them. Materials for turning will be provided.
As with most websites, we do log web visits. This information, however, does not have a link to you personally. These logs help us understand the needs of our audience and the areas of our site that you do or do not find useful. When you simply browse our site, no personal information is being collected.  We may disclose this non-personal information to third parties such as sponsors, clients or advertisers.

A layout square, or combination square, comes in 6” and 12” sizes. Most woodworkers use the 6” model, simply because it’s easiest to carry around. Also, most of the stock you’ll use will be no bigger than 6” wide, so 12” is overkill. The layout square is a triangle that you can use to mark square cuts on stock. Once you measure the length of the cut, you line up the layout square with the edge of the board. The short side will give you a straight, square cut across the end grain. You can also measure off angles with the layout square. This helps when you’re trying to measure for a bevel on a table saw, or marking a cut for a miter saw. You can even use your layout square to determine an existing angle. Just be sure to buy one made of metal. The plastic ones are not only fragile, but they also can warp, making them pretty useless.


As with most websites, we do log web visits. This information, however, does not have a link to you personally. These logs help us understand the needs of our audience and the areas of our site that you do or do not find useful. When you simply browse our site, no personal information is being collected.  We may disclose this non-personal information to third parties such as sponsors, clients or advertisers.
Using wood glue and 1 1/4" pocket hole screws, attach the frame you just built (36" x 11") to the 4x4 frame posts. You will use the pocket holes you drilled in the 36" boards. The frame will sit on the edge of the grooves, not inside. See plans for details. The frame should sit flush with the tops of your 4x4's. This will make the bottom 4" off the ground.
Introductory carpentry classes provide students with an overview of the methods and technologies used in residential and light commercial carpentry and are typically taken at the beginning of a carpentry program. Hands-on experience and lectures make up the class content, which can cover building codes, site layout, estimating, interior and exterior finishes, framing and cabinetry. Additional subjects of instruction may include footing and foundation forming, concrete specifications, OSHA/WISHA construction safety standards and basic carpentry math.
After you learn the basics from this video and article I encourage you to look at the bottom of this article for a list of links, books, and DVDs that will expand your understanding beyond the scope of this article. But this book is the best resource I have found so far: “Understanding Wood: A Craftsman’s Guide to Wood Technology” by R. Bruce Hoadley.
Corona coffee table is another beautiful and wonderful instance that if painted white color can be reasonably inserted into a good-looking Scandinavian interior design. The corona coffee table a long life comparing to many other tables. The material of the corona coffee table is pretty hard and useful. Due to well structure, this table is beautiful.
Once the vinegar solution dries (or if you decided not to do the solution) you can go ahead and stain the project. First use a rag or air compressor to remove any dust from the table. Then use a clean rag to apply the stain of your choice. Don't forget to wear gloves and ventilate the area. Have a brush in your other hand to stain hard to reach areas.

Dan, I’m worried about you. The stress must be getting to you. Somehow you’ve lost your ability to count. By my estimation, your list has at least 29 items, some of which are actually “sets” of items, like chisels or crayons, which I only counted as one item. Perhaps you need a break from all that blogging, and time to get back to basics, like counting. I can help. Come over to my shop and we can count things like parts, items on the honey-do list, and for extra credit, screw holes. Don’t worry about making mistakes, I’ll guide you through it, and we can round up if necessary. Ha!


Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.
This is also a table made from a repurposed pallet. There’s not much you need to change about the pallet, except rearrange a few boards and make the frame smaller. The fact that each board has a slightly different color tone gives the table a special charm. The hairpin legs are a really nice touch. Check out the full tutorial to find out more about how you can build something similar for your own home.
Creativity knows no limits and this chicken coop coffee table proves it. It’s something that we found on findinghomefarms. It’s a one-of-a-kind piece with lots of character, the type of table that makes a statement no matter where you put it. Of course, such a daring and unusual project is not exactly very versatile so you’d need a certain type of decor to make it fit.
Online carpentry education opportunities may be offered as certificate programs or as career diplomas. In programs like these, you'll practice basic carpentry in addition to studying building codes, blueprint reading, math and business management. The courses will typically cover roofing, wall paneling, wood-joining techniques and materials estimation, among other topics. You'll also learn how to use hand and power tools. Depending on the program, you might even take a Spanish course.
We have a bunch of other interesting designs to show you as well. Some, like this one, are meant to make the area around them feel inviting and cozy so the design is simple and familiar. These coffee table plans come from ana-white. You can make them your own by customizing certain aspects of the project. For instance, you could choose to paint the wood and then give it a distressed look instead of using wood stain.
Description: Every woodturner enjoys the opportunity to give handmade ornaments to friends and family during the holidays, especially one that is made purely out of wood. No pre-made ornament kits or ornament hardware will be used in this class. One might call it au naturel!!!! During this class you will be given the opportunity to see various ornaments that have been turned on the lathe, ranging from small and simple to large and more decorative. Class objectives include, but are not limited to, the following: Wood choice (more common ornament wood species and pros and cons of each) Discussion and demonstration on how ornaments can be colored using a variety of markers, paints, dyes, and gilder's paste. Discuss and demonstrate how a variety of gouges and tools can be used to make ornaments, including texturing tools. Sharpening techniques - the instructor will assist all students when sharpening tools Ornament rough sketch and design, before the wood is on the lathe. Most important, every student in class will be given the opportunity to turn at least one ornament of their own. The instructor will assist with basic sketch and design, and will rotate among all students to assist with cuts, tool use, technique, sharpening, and helpful hints. Experience level: Beginner (some turning experience highly preferred) Suggested tools: Turning tools will be supplied; however, students are encourage to bring their own tools if they have them. 3/8" or 1/2" spindle gouge, narrow parting tool, and small roughing gouge is a great start. Students who wish to bring their own chuck may do so as well (1"-8 tpi, 2" or 50mm dovetail jaws, and pin jaws). Lunch break from 12:00 to 12:45
Like you, I too am benchless. I built the “Mozilla” Molson vice variant from last year’s issue (I forget which) and it comes in handy for a lot of operations. I clamp it down to a piece of plywood that I have covered with formica (actually, it’s two pieces that I have piano-hinged together for easier storage) laid across two sawhorses. As long as lateral thrust is not involved, this is a pretty stable way to work. I also have a Zyliss vise for working on smaller pieces. I’ve made do for nearly forty years with a radial arm saw and circular saw. I have only recently acquired a planer and router table (both on wheels) It makes the garage croweded because also sharing the space are two motorcycles and about 400 board feet of rough sawn Camphor. I currently attend classes in woodworking and this coming semester I’ll be enrolled in a class for handtools only (and sharpening).
Along with your materials, there will usually be practical exercises that you can do at home. Illustrated textbooks and study guides, along with instructional videos, will guide you through construction techniques step-by-step. And if you still need additional help, you can always contact your instructor via phone, e-mail, chat or some other method.

Once the vinegar solution dries (or if you decided not to do the solution) you can go ahead and stain the project. First use a rag or air compressor to remove any dust from the table. Then use a clean rag to apply the stain of your choice. Don't forget to wear gloves and ventilate the area. Have a brush in your other hand to stain hard to reach areas.
Chic white coffee table with blag legs and with amazing natural garden like spell! This happens due to built-in planter that make you feel like you are sitting in a garden while being around this coffee table! Grow your favorite flowers or herbs in the integrated planter or simply use it as an ice box for your beverage parties! Want to copy this versatile table design now? Step-by-step DIY tutorial here abeautifulmess

Whether you need a simple sander for your shop or you need a 5-axis, dual process CNC router, we've got you covered. Our product ranges from the most basic woodwork machines to the newest technologies available on the market including CNC machines. We partner with some of the top brands in the industry to ensure you get the highest quality product, at the best possible price.


Most carpenter classes and courses lead to a certificate or associate's degree. Graduates can work in many different specialty areas including residential and commercial carpentry. According to the U.S. Bureau of Labor Statistics, 1 in 3 carpenters are self-employed, so some courses include basic business skills for carpenters like cost estimating and project planning. Primarily, however, students will learn about tools, materials and building techniques.
First, build two boxes for each leg assembly. These are attached using wood glue and 2.5” pocket hole screws through the horizontal boards and into the vertical boards.  You want your pocket holes facing the outside of the box on this part because we will cover them with another board on the next part.  We used our K5 Kreg Jig for this part.  We get asked ALL the time which Kreg Jig to start with.  We always suggest the K5.  We use it on almost every build.  You can find it HERE on Amazon!
Treeline offers only the finest wood carving tools and supplies. Everything from Treeline is backed by our 30-day guarantee against any defects. We have been providing wood carving tools since 1997 and we strive to excel in customer service and quality products. All employees at Treeline are very knowledgeable and professional, so if you are looking for the right woodcarving tools, contact us and we will do our best to help you.

It all depends on the program. Some programs are designed for those already working in the construction industry. Other programs are open to anyone, regardless of their background. Some classes have a specific date by which you must have all of your work completed. Others impose no time limits and give you an unlimited timeframe to complete your work.


There are no formal education or training requirements to become a carpenter in the U.S., but the BLS reports that three to four years of experience is the industry standard for becoming a skilled craftsperson. Training and experience can be acquired by working with an experienced journeyman or through an apprenticeship offered by an employer or labor union. Formal in-class instruction is offered through certificate, diploma or associate's degree programs in carpentry at trade or vocational schools. Employees with some formal carpentry education generally start at higher positions in the field. Carpentry courses may include carpentry math, building layouts, foundation work, roofing, stair construction, siding and moldings. You can also study interior and exterior finishes.
No matter what type of wood working equipment you are looking for, Hermance is here to help. We offer one of the largest selections of general woodworking machinery online. Whether you're in the market for a boring machine, table saw, dust collector, or even an end matcher- you're sure to find what you're looking for in our listings of general woodworking machinery.
Moving on to the top of the table. This will be assembled identical to the first shelf assembly, but the depth of the plywood will change. Grab a coupld scraps of the barnwood or planks you are going to use on the top. Lay them flat on a table, and lay the plywood on top of them with the pocket holes facing up. Now attach the long boards first using glue and 1.25” pocket hole screws. After those are attached, you can attach the shorter ends. These will attach with both 3/4 and 2.5” pocket hole screws.
×