The Amish here in Ohio use a nifty wooden rule for calculating bd. ft. It has a brass football shaped hook on the end and they’re about 2′ long. Three columns of numbers run down the length of stick. These columns are the length of stock say, 12,14,16 foot. Within these columns, bd. ft. has already been calculated and marked. For a 16′ bd. the hook is placed over one edge and a reading of bd. ft. is taken from opposite edge from the 16′ column. “Audels Carpenters and Builders Guide #1” pg. 146, shows a good example. They call… Read more »

The most common type of cedar is the western red variety. Western red cedar, as its name implies, has a reddish color to it. This type of wood is relatively soft (1 on a scale of 1 to 4), has a straight grain, and has a slightly aromatic smell. Western Red cedar is mostly used for outdoor projects such as furniture, decks, and building exteriors because it can handle moist environments without rotting. Western red cedar is moderately priced and can be found at most home centers.
1: Table saw in place of a jointer. Any number of tips in previous issues address straightening edges of boards without a jointer. A jointer serves one purpose, but a tablesaw can serve many (just watch your local Craigslist for a decent one to come up.) The thickness planer is unavoidable, but until you can afford one, buy stock in the thickness you need.
Ashworth College is unlike any other carpentry school online. Our Carpentry training focuses on the real-world tools, knowledge, and procedures used by construction professionals on residential and commercial building projects. Studying online in a way that fits your busy life, you’ll graduate with the carpentry skills employers demand, helping you focus on practical skills and turn your woodworking hobby into a true profession.
The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.
Description: Now that you have your new lathe tools, come join us to learn how to sharpen your chisels so that you can get the best performance from your equipment. You will be taught several different methods that can be used to keep your tools sharp and effective. You will be learning how to sharpen all of the basic lathe tools. This is a "must have" class for beginning woodturners.
A successful joiner can see the full picture of the project he is preparing to run and for SCM woodworking machinery come to his aid with devices made especially for woodworking machinery; devices that allow to not having to perform the mathematical calculations necessary to make a precise angular cut on a circular saw (with our compex for example) or a template that can produce pieces that are exactly identical among them (on our lathe minimax t 124).
The multi-function coffee table creation can assist as a picnic ensemble, coffee table, and storage unit all in one. Spread your creations and reprocess wooden pallets into reasonable pieces you possibly utilize for a long time. Many individual use this type of coffee table their homes for the reason that you can use this table for different purposes.
Framing is another part of carpentry. Framing takes skill and experience it’s not a part of carpentry that anyone can just jump into. The skills that are required in framing is plumbing up a wall, make sure studs are 16 on center or whatever the specs calls for. Developing a good eye for straightness in carpentry work. Last but not least making sure everything is level.
It’s good to know that when it comes to choosing wood to buy that there are somethings that we need to take into consideration. I like how you mentioned that one thing we need to consider is whether we need it to be hard or soft for the project we are needing it for. This is something that we will have to look at and do more research on to make sure that we make the right decision. 

The campaign features a new customer-focused website, new advertising centered on visually-appealing wood applications, and the launch of Northwest Hardwoods’ Pinterest and Instagram accounts to convey visual ideas and aspirations for the many uses of hardwoods. The campaign offers an opportunity for Northwest Hardwoods to reach out to new audiences including designers, specifiers, architects and OEMs, underscoring the fact that no other building and design material is as visually appealing and as sustainable as timber. Additionally, the campaign includes the creation of product specific communications outreach that will support the company’s sales objectives.


The oak contrast coffee table is pretty popular in these days. The natural oak has a beautiful texture that must be put to the worth by making bold contrasts among the oak top and the other body of the table. There is numerous table in the market for sell because of many individuals like this these tables and want to purchase oak contrast coffee table.
Teak is becoming rarer as the days go on, but it is the staple for fine outdoor furniture. Teak is highly weather-resistant and beautiful (not to mention expensive — can you believe almost $24 a board foot?). Teak has an oily feel and a golden-brown color. It rates a 3 on a scale of 1 to 5 for hardness and is only available from larger lumberyards and specialty suppliers.

1: Table saw in place of a jointer. Any number of tips in previous issues address straightening edges of boards without a jointer. A jointer serves one purpose, but a tablesaw can serve many (just watch your local Craigslist for a decent one to come up.) The thickness planer is unavoidable, but until you can afford one, buy stock in the thickness you need.
We really like the distressed look on this coffee table. There are a few ways in which you can achieve that. You can use reclaimed wood or you can create the antiqued finish artificially using special techniques. You can analyze the plans and the instructions shared on instructables to find out more about this strategy. They also show you how to build this stylish pinstripe table.
Certain species of wood have traditionally been associated with different styles of furniture. The wood of choice for the Arts & Crafts movement was quarter sawn white oak, valued for its appearance, durability and dimensional stability. An Arts & Crafts style piece executed in maple might be a well-made example of a classic style, but the choice of wood would be visually at odds with the design. Pine and other softwoods impart a more relaxed, country influence, while traditional hardwoods, such as cherry and walnut, are more likely to be associated with fine furniture.
Like you, I too am benchless. I built the “Mozilla” Molson vice variant from last year’s issue (I forget which) and it comes in handy for a lot of operations. I clamp it down to a piece of plywood that I have covered with formica (actually, it’s two pieces that I have piano-hinged together for easier storage) laid across two sawhorses. As long as lateral thrust is not involved, this is a pretty stable way to work. I also have a Zyliss vise for working on smaller pieces. I’ve made do for nearly forty years with a radial arm saw and circular saw. I have only recently acquired a planer and router table (both on wheels) It makes the garage croweded because also sharing the space are two motorcycles and about 400 board feet of rough sawn Camphor. I currently attend classes in woodworking and this coming semester I’ll be enrolled in a class for handtools only (and sharpening).
Cut 2- 1x6 46" boards, mitered at 45 degrees on each end (measurement is taken on long side). Cut 2- 1x6 17" boards, mitered at 45 degrees on each end (measurement is taken on long side). Drill pocket holes in both ends of each board. Drill several pocket holes (3 or 4) on the INSIDE edges of each board. Spread wood glue on the edges of each board, and sandwich them together, using bar clamps to keep them tight. Using 1 1/4" pocket hole screws, attach the 1x4's together. (see photo on previous step) 

If you all looking for a a spicy addition to your living room storage space then do choose this pretty wooden coffee table! It comes also with 2 build in drawers that will be a stylish way to store your living room concerns! Design is full of style and milk-choco appeal of coffee table just held all precious and special to eyes! Full directions and DIY guide here hertoolbelt
We cut the decorative diagonal pieces to fit on this part. Mark each board with your pencil and cut them to fit exact. You can check out the video if you have questions about this part! We walk you through it. Cut the diagonal pieces to fit first, then mark and attach them to each other using wood glue and nails. Then, fit them in the box and attach them with wood glue and nails through the box and into each end of the X piece. 

Often referred to as Douglas Fir, this wood has a straight, pronounced grain, and has a reddish brown tint to it. Fir is most often used for building; however, it’s inexpensive and can be used for some furniture-making as well. It doesn’t have the most interesting grain pattern and doesn’t take stain very well, so it’s best to use it only when you intend to paint the finished product. Douglas fir is moderately strong and hard for a softwood, rating 4 on a scale of 1 to 4.
This woodworking plans project is a Bentwood Coffee Table that is a challenging design for those who would like to try a project which requires wood bending. The contemporary lines combined with traditional natural wood allow this table to fit comforatbly with many other styles of furnishings. The technique for bending the wood does not require any special tools or steaming processes.
There are three very important elements that must come together in making a project that will not only be pleasing to the eye, but will stand the test of time: good design, careful workmanship and meticulous selection of materials. You can continue to refine your design on paper, but at some point you will have to make that transition from a two dimensional drawing to selecting the lumber to use for each part. This can be one of the most difficult phases of any project and one that has the greatest effect on the final appearance of your finished piece.
Second, I have another call for entries – I have, for some time, wanted to make a “Woodworker’s Vacation Map,” one that would list and plot a wide array of interesting places and sights across the world. Whenever I travel, I ask a few woodworking friends from the area I’m traveling to what I should see. This has exposed me to a wide range of beautiful experiences, often tucked away and lacking signage.
Most chisels are beveled on the 2 sides and on the cutting edge, but specialty chisels may only be beveled at the cutting edge. This bevel will be at 20 to 25 degrees down the length of the blade on one side, and flat on the backside. The blade will be between 4” and 7” long. Make sure you get chisels with a grip that fits your hand. If the grip is too small, you won’t be able to hold the chisel steady as you work. Be sure to use a mallet or wood hammer when you work, so that you don’t destroy the head on your chisel. Keep track of the edge caps, keep them sharp, and oil the metal now and then after you’ve used them, and they should be good for years. If you don’t have the edge caps, get a roll to keep them in. This will prevent them from bouncing around in your tool box drawers and getting damaged.
We have a bunch of other interesting designs to show you as well. Some, like this one, are meant to make the area around them feel inviting and cozy so the design is simple and familiar. These coffee table plans come from ana-white. You can make them your own by customizing certain aspects of the project. For instance, you could choose to paint the wood and then give it a distressed look instead of using wood stain.
Lumber for your projects can come from many sources, but before you can use it to build anything, it must be dry. Lumber that is kiln dried will have a moisture content right out of the kiln of 7 or 8%. However, by the time the lumber is delivered to your local dealer and arrives at your shop, the moisture content may have changed dramatically. Storage conditions between the kiln and your shop are clearly out of your control, so it is always a good idea after purchasing lumber to acclimatize it in your shop for several weeks. To avoid using lumber that is still in the process of adjusting to its new environment it is best to use a moisture meter to verify the moisture content of the wood. Most dealers don't mind customers checking the moisture content at the yard as long as they are using a pinless meter. The meter in my lumber kit uses electromagnetic waves to calculate the moisture content of a given piece of wood. Its use couldn't be simpler or quicker – simply turn it on, enter the species, and place the meter on the wood to be measured. The result is displayed right on the screen instantly without the need for conversion tables and other calculations. Typically, I check a couple of areas on each board as I select them just to confirm they are all in the same moisture range. Back at the shop I once more check each piece of wood and note it in chalk on the board. Every few days I'll recheck the boards, and when the readings have stabilized, I can be reasonably certain there won't be any surprises when I start the milling process.
Loveland lies in Larimer county, which is one of the 55 counties in Colorado. Overall, the Fort Collins-Loveland area has 128,650 total employed workers according to the US Bureau of Labor Statistics, with a 2% unemployment rate, $21/hr average worker wage, and a $43,210 average annual salary. Thus, about 6 out of every 1000 jobs in Loveland are held by carpenters, and 6/1000 are held by construction laborers. 

Carpentry students from Loveland schools who go on to become carpenters, construction managers, construction workers, construction engineers, etc. have a good chance at finding employment. For example, there are 743,760 people working as carpenters alone in the US, and their average annual salary is $43,640. Also, Construction laborers make on average $33,190 per year and there are about 856,440 of them employed in the US today. In fact, in the Fort Collins-Loveland area alone, there are 760 employed construction laborers earning an average salary of $29,460. Carpenters in this area earn $39,170/yr and there are 770 employed.
The topic of lumber confused me mainly because I couldn’t find a simple summary of the topic. I found a lot of complex discussions with different terms used by different “experts”. I am by no stretch of the imagination a lumber expert, but I’m very good at simplifying complex topics so that everyone can understand. As a result, this is a simple practical guide to help you understand how wood moves, what wood to buy, how to buy it, and where to buy it.

The multi-function coffee table creation can assist as a picnic ensemble, coffee table, and storage unit all in one. Spread your creations and reprocess wooden pallets into reasonable pieces you possibly utilize for a long time. Many individual use this type of coffee table their homes for the reason that you can use this table for different purposes.
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking.   These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email orderdesk@canadianwoodworking.com  and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence. 
The next hand tool every woodworker should have is a nail set. In fact, you should have several sizes. They look like awls, and you use them to drive nail heads into the wood so they are flush or right below the surface. This allows you to fill the holes and prepare for staining or painting. The nail setter will usually have either a convex or concave surface to grip the nail better and keep it from sliding off and marring the wood.

“Basic,” on the other hand, is a word that allows for growth – and that’s exactly what you want in your woodworking tool kit. You want to be able to take the same kit with you through many years in the craft. With my basic woodworking tools list, I wanted to provide a core set of tools that will serve you well from project to project. I’m especially concerned these days with the transition to hardwood furniture making, as opposed to plywood boxes of various sizes. That’s the transition I’m making right now in my own work!

Poplar is one of the less expensive hardwoods. It’s also fairly soft (1 in hardness on a scale of 1 to 5), which makes it easy to work with. Poplar is white with some green or brown streaks in the heartwood. Because poplar is not the most beautiful wood, it’s rarely used in fine furniture, and if it is, it’s almost always painted. Poplar can be a good choice for drawers (where it won’t be seen) because it is stable and inexpensive. You can find poplar at larger home centers, but a lumberyard will have a better selection.
This small coffee table is ideal for a side table or end table. The table is designed with the home handyman in mind. It is both easy to build and is very sturdy. The minimum tools required to construct this coffee table are... Pencil; square; measuring tape; handsaw; hammer; chisel; a couple of clamps and lots of sandpaper. Most handymen are likely to have those tools in their arsenal. Of course... it would make life easier if you also happened to have a drop-saw and a belt sander. The wood used for this coffee table was 90mm x 45mm (1 1/2 x 3 1/2 inches) dressed/surfaced cedar. Cedar is reddish in color, light and easy to work with. Other wood can be used. Virtually any wood can be used for this project, just allow for different widths and thicknesses, and also take into account, the finish. Is the table to be painted, stained and/or coated with polyurethane? Obviously, if the table is to be painted, then an inferior and less expensive wood can be used, as imperfections (within reason) can be filled and painted over.
Framing is another part of carpentry. Framing takes skill and experience it’s not a part of carpentry that anyone can just jump into. The skills that are required in framing is plumbing up a wall, make sure studs are 16 on center or whatever the specs calls for. Developing a good eye for straightness in carpentry work. Last but not least making sure everything is level.
Cut 2- 1x6 46" boards, mitered at 45 degrees on each end (measurement is taken on long side). Cut 2- 1x6 17" boards, mitered at 45 degrees on each end (measurement is taken on long side). Drill pocket holes in both ends of each board. Drill several pocket holes (3 or 4) on the INSIDE edges of each board. Spread wood glue on the edges of each board, and sandwich them together, using bar clamps to keep them tight. Using 1 1/4" pocket hole screws, attach the 1x4's together. (see photo on previous step)

This is the side table version of the stylish project we shared previously. In certain configurations, it could function as a coffee table. It’s a design suitable for small spaces. The wooden top has this hollow storage compartment which is great for keeping things like a book, a magazine, the remote control or the phone when relaxing on the sofa. The hairpin legs give the table a slender look.


2 small Japanese pull saws, a western push saw, fret saw, set of chisels, bit brace with a roll of arbor bits, rabbet plane, side rabbet (trim) plane, 2 shoulder planes, 3 set of diamond stones, slip stone, multiple files, a rasp or two, 2 small bar clamps, a mini vise, hand scrapers, scratch beader with cutters, combination plane with cutters, smoothing plane, jack plane, block plane, combination square, steel straight rule, 12′ tape measure, small bottle of glue, a few short dowels, 2 marking gauges, and a few different marking instruments (awl, pencils, marking knife).
I work with a lot of rough sawn boards (Wood Mizer) that are up to 12 inches wide. The worse defect is twist. First I saw the stock to rough project lengths and then using winding sticks, I attack the twist with a #5 hand plane, gradually moving the winding sticks toward the center. If there is bow or cup I can plane that out also. I now have a reference surface that can go thru my planer. The finished boards are perfect. This is not really difficult or excessively time consuming.
WoodAndShop.com recommends products, with links to online stores, some of which are part of affiliate programs. If users make purchases in those stores (e.g. ebay.com and Amazon.com) those affiliate links lead to referral compensation to us. These payments are very helpful to us, and add no additional fees to our users, so we are grateful for anyone who uses the affiliate links. We run our website based on principles of integrity, and don’t recommend any product that we wouldn’t use ourselves. Any product claim about a service or product should be verified with the manufacturer.
For furniture making, the best, most stable stock has the annual growth rings intersecting each face at approximately the same angle, roughly 45º. Wood cut this way is referred to as quarter sawn. Milling quarter sawn lumber is a labour intensive process, which is why it costs more than plain-sawn lumber. The appearance of the grain will tend to be similar on all four sides. This makes quarter sawn lumber a great choice for table legs, rails and stiles of frame and panel doors, or for any part where two adjacent sides are visible.
2 small Japanese pull saws, a western push saw, fret saw, set of chisels, bit brace with a roll of arbor bits, rabbet plane, side rabbet (trim) plane, 2 shoulder planes, 3 set of diamond stones, slip stone, multiple files, a rasp or two, 2 small bar clamps, a mini vise, hand scrapers, scratch beader with cutters, combination plane with cutters, smoothing plane, jack plane, block plane, combination square, steel straight rule, 12′ tape measure, small bottle of glue, a few short dowels, 2 marking gauges, and a few different marking instruments (awl, pencils, marking knife).
When you've selected your lumber, restack the pile neatly. Before heading off, calculate the number of board feet you have pulled just to be sure you have enough. It's advisable to allow for errors, waste and slight changes in plan when purchasing your material. Depending on the material and the complexity of the project I'll typically allow from 10 to 40% extra.

Often referred to as Douglas Fir, this wood has a straight, pronounced grain, and has a reddish brown tint to it. Fir is most often used for building; however, it’s inexpensive and can be used for some furniture-making as well. It doesn’t have the most interesting grain pattern and doesn’t take stain very well, so it’s best to use it only when you intend to paint the finished product. Douglas fir is moderately strong and hard for a softwood, rating 4 on a scale of 1 to 4.

All Alison courses are free to enrol, study and complete. To successfully complete this Diploma course and become an Alison Graduate, you need to achieve 80% or higher in each course assessment. Once you have completed this Diploma course, you have the option to acquire official Certification, which is a great way to share your achievement with the world. Your Alison Certification is:


The next hand tool every woodworker should have is a nail set. In fact, you should have several sizes. They look like awls, and you use them to drive nail heads into the wood so they are flush or right below the surface. This allows you to fill the holes and prepare for staining or painting. The nail setter will usually have either a convex or concave surface to grip the nail better and keep it from sliding off and marring the wood.
I’m currently working on a dining room table with this color in mind (I also plan on a coffee table soon). I’ve been testing out stain colors and dark walnut is currently in the lead. I love the way this coffee table turned out in color. How many coats of stain did you use? Also, did the dark wax make a big difference in color? I was planning on using a satin poly for sealant (mostly because it’s what is most convenient and what I’m accustomed to), but I’m interested in the dark wax after seeing this post. Any recommendations you have are much appreciated.
×