1. Power jointer and thickness planer. I have developed various means of straightening the edges of my stock with hand-held tools, but I don’t see a way to efficiently flatten the faces of rough or reclaimed lumber without a power jointer. It’s part of the first few steps for any furniture project, and I want to be able to move through this step quickly and into the more interesting work. The thickness planer is also a huge time-saver, compared to hand-held tools.
Often referred to as Douglas Fir, this wood has a straight, pronounced grain, and has a reddish brown tint to it. Fir is most often used for building; however, it’s inexpensive and can be used for some furniture-making as well. It doesn’t have the most interesting grain pattern and doesn’t take stain very well, so it’s best to use it only when you intend to paint the finished product. Douglas fir is moderately strong and hard for a softwood, rating 4 on a scale of 1 to 4.
Thanks so much with your patience with the site this morning.  We are growing (it's a good thing!) and are due for a server upgrade, but ALWAYS know keeping the site up and running fast is super important to me, and we are working very hard to improve the user experience of this site.  What can I say?  I APPRECIATE you each and every time you visit, and want to make sure each time you visit is pleasant for you.  Thank you!

This woodworking plans project is a Bentwood Coffee Table that is a challenging design for those who would like to try a project which requires wood bending. The contemporary lines combined with traditional natural wood allow this table to fit comforatbly with many other styles of furnishings. The technique for bending the wood does not require any special tools or steaming processes.
Looking at the back-right Leg, lay a ½ x ½ dowel along the Leg to act as a spacer. Now place the ends of the Shelf Support and Apron against the Leg as shown. Apply glue to the end of each board, clamp it in place, and then attach it using a drill/driver and 1¼ inch pocket hole screws. Attach the opposite end of each board to the adjoining Leg. Repeat to join the Front Legs with the front Shelf Support and Apron Boards.
This small coffee table is ideal for a side table or end table. The table is designed with the home handyman in mind. It is both easy to build and is very sturdy. The minimum tools required to construct this coffee table are... Pencil; square; measuring tape; handsaw; hammer; chisel; a couple of clamps and lots of sandpaper. Most handymen are likely to have those tools in their arsenal. Of course... it would make life easier if you also happened to have a drop-saw and a belt sander. The wood used for this coffee table was 90mm x 45mm (1 1/2 x 3 1/2 inches) dressed/surfaced cedar. Cedar is reddish in color, light and easy to work with. Other wood can be used. Virtually any wood can be used for this project, just allow for different widths and thicknesses, and also take into account, the finish. Is the table to be painted, stained and/or coated with polyurethane? Obviously, if the table is to be painted, then an inferior and less expensive wood can be used, as imperfections (within reason) can be filled and painted over.
Furniture Making engages students in the process of furniture making. Topics include an American historical overview and a look at the use of power and hand tools. Common themes include sketchbook work, cutting, hand tools, power tools, bending and jig making. This course employs various technical readings, visual aids, videos, project pictures and assignments.
This small coffee table is ideal for a side table or end table. The table is designed with the home handyman in mind. It is both easy to build and is very sturdy. The minimum tools required to construct this coffee table are... Pencil; square; measuring tape; handsaw; hammer; chisel; a couple of clamps and lots of sandpaper. Most handymen are likely to have those tools in their arsenal. Of course... it would make life easier if you also happened to have a drop-saw and a belt sander. The wood used for this coffee table was 90mm x 45mm (1 1/2 x 3 1/2 inches) dressed/surfaced cedar. Cedar is reddish in color, light and easy to work with. Other wood can be used. Virtually any wood can be used for this project, just allow for different widths and thicknesses, and also take into account, the finish. Is the table to be painted, stained and/or coated with polyurethane? Obviously, if the table is to be painted, then an inferior and less expensive wood can be used, as imperfections (within reason) can be filled and painted over.
Description: In this four day class, we will start with rough lumber and finish with a simple box. Along the way we will teach you how to use the jointer, planer, table saw, and router table This is THE class to take if you are interested in getting started the right way in woodworking. This one will fill up fast, so sign up. soon. Woodworking 101 is strongly recommended for beginners and people looking to review the basics.

You’ll need a long screwdriver with a square blade that is very heavy duty. This gives you a lot of torque. You’ll also need a small and medium slot screwdriver. For working on cabinets or tight places in woodworking, you’ll need a screwdriver with a thin shank so that you can reach screws that are inside of deep holes. This is accomplished with a cabinet screwdriver. Get a couple of medium Phillips head screwdrivers, and a stubby one too, for those tight places. You may also want a ratcheting screwdriver. 

To us it is clear: Power, passion and conviction in the process of creation is what drives us and makes us so successful. The common objective is this, both today and for the future, to build the best woodworking machines with respect for our customers and for our environment. This is reinforced with each machine that leaves our factory in Hall in Tirol.
A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.
All Alison courses are free to enrol, study and complete. To successfully complete this Diploma course and become an Alison Graduate, you need to achieve 80% or higher in each course assessment. Once you have completed this Diploma course, you have the option to acquire official Certification, which is a great way to share your achievement with the world. Your Alison Certification is:
As with most websites, we do log web visits. This information, however, does not have a link to you personally. These logs help us understand the needs of our audience and the areas of our site that you do or do not find useful. When you simply browse our site, no personal information is being collected.  We may disclose this non-personal information to third parties such as sponsors, clients or advertisers.
I've found that it is easiest to attach the shelf by attaching the 2×2 side rails prior to connecting it to the table. To do this you'll sort of take a minor step back by removing the two lower 2×2 side rails (only 8 screws). Then drill the shelf to the 2×2's as shown below. Lift the shelf into place and attach each end of the shelf to the lower end rails using 2 1/2″ Kreg Screws. Once that is secure flip the table right side up and add the cross supports.

Because the Tabletop is made form several slats of wood, I like to use Figure 8 Top Fasteners to allow the Tabletop boards to expand and contract. To install the fasteners, first mark the placement of each fastener on the apron–I placed three fasteners along each long Apron Board, and two on each End Apron Board. Outline half of the faster on the top edge of the Board.


One name rang out like a bell at multiple forums, from many different woodworkers: Steve Wall Lumber. From what we read (NOT direct experience!) it looks like the only way you can go wrong with Wall Lumber is if they don’t have what you’re looking for. The other frequently-cited lumber sellers are worth looking into for sure, as it’s always good to have multiple sources!
Scm specializes in designing and manufacturing woodworking machines and services for joineries and customized production shops working with melamine panels, solid wood and other plastic materials. All machines are configured to offer the best technological innovations, high performance and reliability. Easy to install and easy to use, Scm products are distributed all over the world.  

Introductory carpentry classes provide students with an overview of the methods and technologies used in residential and light commercial carpentry and are typically taken at the beginning of a carpentry program. Hands-on experience and lectures make up the class content, which can cover building codes, site layout, estimating, interior and exterior finishes, framing and cabinetry. Additional subjects of instruction may include footing and foundation forming, concrete specifications, OSHA/WISHA construction safety standards and basic carpentry math.
This Privacy Policy covers CanadianWoodworking.com's treatment of personally identifiable information that CanadianWoodworking.com collects when you are on the CanadianWoodworking.com site, and when you use CanadianWoodworking.com's services. This policy also covers CanadianWoodworking.com's treatment of any personally identifiable information that CanadianWoodworking.com's business partners share with CanadianWoodworking.com.

Loveland lies in Larimer county, which is one of the 55 counties in Colorado. Overall, the Fort Collins-Loveland area has 128,650 total employed workers according to the US Bureau of Labor Statistics, with a 2% unemployment rate, $21/hr average worker wage, and a $43,210 average annual salary. Thus, about 6 out of every 1000 jobs in Loveland are held by carpenters, and 6/1000 are held by construction laborers.
While flipping through the boards, keep an eye open for signs that a number of boards may have come from the same tree. Looking at the ends and the growth rings will tell you where in the log the board was sawn. In some cases, knots may go through more than one board, and often the outer boards have a live edge. By comparing these features, the colouring, grain and other distinguishing marks, it is often possible to identify several boards cut from the same log.
After you've used one of these free coffee table plans to build your dream coffee table, check out these other free woodworking plans for bookcases, TV stands, dressers, nightstands, step stools, entertainment centers, farmhouse tables, desks, jewelry boxes, dining room tables, wine racks, picnic tables, kitchen islands, home bars, bunk beds, toy boxes, and even dog houses.

Description: When you have reached that point in your turning, where you are ready to challenge yourself with something new, this class will teach you some proven techniques for turning simple hollow forms. Students will have the opportunity to use a variety of turning tools and hollowing tools. You will also learn sharpening techniques for these tools. We will also discuss design options and aesthetics, and learn various finishing techniques. All students are encouraged to bring their favorite turning tools to use on this project.

Commercial carpenters build and remodel commercial office buildings, hospitals, hotels, schools, and shopping malls. Some specialize in light-gauge and load-bearing steel framing for interior partitions, exterior framing, and curtain wall construction. Others specialize in concrete forming systems and finishing interior and exterior walls, partitions, and ceilings.


However, if you want to stain or clear-coat the project, you'll have a number of choices to look through. Since your local home center megamart will probably only carry a couple of hardwood species (poplar and red oak are common) spend time at a fine wood supplier and look through the vareties available. They should be able to help you determine how each species will look when finished, which will go a long way toward refining your decision.
I’d like to add some type of sharpening system to your list. A simple sandpaper and slab system, stones, or the more expensive slow grinder system. Although listed, files should be in this sharpening/maintenance category as well. You’ll need these as soon as you purchase a majority of hand tools. They’ll be needed throughout each day of using the tools. Initial setup and routine maintenance will give better results with less fighting the grain and tool. Whether your a beginner or a master, the tools must be sharp and maintained.
“The earliest credible evidence of coffee-drinking appears in the middle of the 15th century in the Sufi shrines of Yemen. It was here in Arabia that coffee seeds were first roasted and brewed, in a similar way to how it is now prepared. Coffee seeds were first exported from Eastern Africa to Yemen, as the coffee plant is thought to have been indigenous to the former.Yemeni traders took coffee back to their homeland and began to cultivate the seed. By the 16th century, it had reached the rest of the Middle East, Persia, Turkey, and northern Africa. From there, it spread to Europe and the rest of the world.” [source]

Having completed this course the learner will be able to: - Describe the history and scope of carpentry as a trade; - Identify the opportunities for carpenters in the construction industry; - Classify the various building materials used by carpenters; - List the most commonly used fasteners and adhesives used by people in the carpentry trade; - Explain the different types of hand and power tools available to carpenters; - Outline the general safety procedures and guidelines that should be followed to operate the tools; - Discuss the importance of employee responsibility and human relations to being successful in the trade; - Identify the various types of construction drawings that make a drawing set; - State the guidelines to read and interpret reading plans and drawings, blueprints, and specifications; - List the various terms associated with floor systems, wall, ceiling and roof framing; - Explain the different methods of framing and constructing houses made of wood; - Describe the types of beams/girders and supports used in construction; - Outline the sequence involved in constructing a platform floor assembly; - Summarize the basic procedure for laying out, assembling, and erecting wood frame walls; - Recognize the different types of roofs used in residential construction; - Determine the length of a common rafter required to construct a roof; - Discuss the terms associated with concrete, concrete reinforcing materials, and formwork; - Apply the concrete mixing information to get different types of concrete, designed to suit various purposes; - Explain the basic concrete curing methods and materials; - List the various components of windows, exterior doors, and stairways used in residential construction; - Summarize the basic installation procedure for pre-hung windows; - State the various types of exterior doors used in residential construction; - Identify the essential requirements for framing stairs; - Describe the design and layout techniques used for stairways and stairwells.
Upcycling and recycling are our mottoes thus it is just natural for old door tables’ transformations to be a segment of a collection of our free point, particularly when this kind of crafts and projects have a reused material and sustainable side enriched by the passage of period. Old wooden door recycled into the table is a very good technique for beginners.

The beverage pallet coffee table is one of the most significant choices for your living room if you live to entertain. It comprises a built-in space for the bucket of the ice storage that possibly keeps your drinks fresh and cold, space which can be tucked away and be covered up when necessary. In this case beverage pallet coffee table is best for you.
Apply glue to the ends of the 1 x 2 End Pieces for the Base and Apron, and then clamp them in place against the inside of the Leg. Position the pieces so that one runs flush with the top edge, and the other sets below the line marked in Step 7. Center both pieces on the leg, and tilt them so that they run parallel to the edge of the Leg. Using a drill/driver and 1¼-inch pocket holes screws, attach the pieces to the Leg. Repeat on the opposite end. 

By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
Now it’s time to attach the top of the table. Line up the 1×6 boards and place the frame you built upside down and centered on the boards. Drill 1 1/4″ screws through the supports into each board to secure them to the table. I used regular wood screws for this step originally, but the heads were sinking into the supports and not pulling the top boards down tight like I wanted. So I swapped them out for the Kreg Jig screws, which have washer heads, and they worked like a charm. If you’re having trouble getting those top boards secured tight, I’d try switching to the Kreg Jig screws!
Put an emphasis on the material used in the design of the coffee table. For example, if you’re using wood, showcase its natural beauty, with knots, cracks and all other imperfections. A live edge top would definitely be a good choice in such a case. Check out these rustic coffee table plans to find out all about the steps leading up to a gorgeous and yet simple design.
Carpentry students from Loveland schools who go on to become carpenters, construction managers, construction workers, construction engineers, etc. have a good chance at finding employment. For example, there are 743,760 people working as carpenters alone in the US, and their average annual salary is $43,640. Also, Construction laborers make on average $33,190 per year and there are about 856,440 of them employed in the US today. In fact, in the Fort Collins-Loveland area alone, there are 760 employed construction laborers earning an average salary of $29,460. Carpenters in this area earn $39,170/yr and there are 770 employed.
Liz Fourez started Love Grows Wild in 2012 with a passion for interior design and homemaking and a dream to help others create a home they love.  From simple project tutorials, to holiday and entertaining ideas, to her journey renovating a 1940’s farmhouse, Liz demonstrates how to create a beautiful and inviting home with a handmade touch. She turned her signature cozy, neutral style into a best-selling book in 2016 and continues to inspire readers with her captivating photography and easy decorating ideas. Read more about Liz > > > >
Carpentry skills can be applied to residential or commercial remodeling, cabinet making and exterior and interior trim. Coursework in carpentry classes commonly includes instruction in building safety, construction codes, framing and site layout. These courses are widely available at technical schools and colleges. Hands-on practice is emphasized in most classes.
To best engage with designers and architects, Northwest Hardwoods has expanded its social media reach to include Instagram and Pinterest. Both channels are visually based and aspirational, which will allow Northwest Hardwoods to showcase not only its many types of wood grades and species, but also the beautiful and varied applications for these woods – from cabinets to decking to furniture.
Teak is becoming rarer as the days go on, but it is the staple for fine outdoor furniture. Teak is highly weather-resistant and beautiful (not to mention expensive — can you believe almost $24 a board foot?). Teak has an oily feel and a golden-brown color. It rates a 3 on a scale of 1 to 5 for hardness and is only available from larger lumberyards and specialty suppliers.
In the sixty years of woodworking I have found two tools of increasing necessity. One is a band saw. I can do most of my work with a band saw and hand plane. The second tool is a bow saw, or actually several bow saws. They will replace the band saw if required, though they are slow. One I made about twenty years ago has a one and a half inch wide rip blade and is about thirty inches long. I think the blade is from an old industrial band saw blade I picked up and sharpened into a rip saw blade. It works very well on ripping lumber, logs, etc. Though it tires me out to much to use it now.
As with most websites, we do log web visits. This information, however, does not have a link to you personally. These logs help us understand the needs of our audience and the areas of our site that you do or do not find useful. When you simply browse our site, no personal information is being collected.  We may disclose this non-personal information to third parties such as sponsors, clients or advertisers.
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.
If you have some experience working with steel and welding pieces together you’ll find this project a piece of cake. These coffee table plans come from instructables. The base has to be welded and that takes a bit of skill and time and then the top is added. The combination of wood and steel is a pretty harmonious ones. The warmth of the wood combined with the rugged-industrial look of the steel result in a beautiful and well-balanced structure.
Thanks so much with your patience with the site this morning.  We are growing (it's a good thing!) and are due for a server upgrade, but ALWAYS know keeping the site up and running fast is super important to me, and we are working very hard to improve the user experience of this site.  What can I say?  I APPRECIATE you each and every time you visit, and want to make sure each time you visit is pleasant for you.  Thank you! 

The last step is to dry brush over top of the white washed surface. Using a dry brush, I used the same linen white chalk paint from Rust-Oleum and dipped the tip of the brush into the paint. Getting just a little paint on the end of the brush, I then dabbed the brush onto a piece of scrap wood to take off any excess paint. Then, going with the grain of the wood, I used quick strokes. You can add more or less depending on the look you desire!


The Amish here in Ohio use a nifty wooden rule for calculating bd. ft. It has a brass football shaped hook on the end and they’re about 2′ long. Three columns of numbers run down the length of stick. These columns are the length of stock say, 12,14,16 foot. Within these columns, bd. ft. has already been calculated and marked. For a 16′ bd. the hook is placed over one edge and a reading of bd. ft. is taken from opposite edge from the 16′ column. “Audels Carpenters and Builders Guide #1” pg. 146, shows a good example. They call… Read more »
×