The Amish here in Ohio use a nifty wooden rule for calculating bd. ft. It has a brass football shaped hook on the end and they’re about 2′ long. Three columns of numbers run down the length of stick. These columns are the length of stock say, 12,14,16 foot. Within these columns, bd. ft. has already been calculated and marked. For a 16′ bd. the hook is placed over one edge and a reading of bd. ft. is taken from opposite edge from the 16′ column. “Audels Carpenters and Builders Guide #1” pg. 146, shows a good example. They call… Read more »

This is also a table made from a repurposed pallet. There’s not much you need to change about the pallet, except rearrange a few boards and make the frame smaller. The fact that each board has a slightly different color tone gives the table a special charm. The hairpin legs are a really nice touch. Check out the full tutorial to find out more about how you can build something similar for your own home.


There are often situations when the original message asks for opinions: "What is the best widget for my type of shop?". To a certain extent, the person posting the message is responsible for including specific questions within the message. An open ended question (like the one above) invites responses that may read as sales pitches. WOODWEB suggests that companies responding to such a question provide detailed and substantive replies rather than responses that read as a one-sided product promotion. It has been WOODWEB's experience that substantive responses are held in higher regard by our readers (return to top).
Solid wood will always remain a top choice where furniture is concerned. Its unique texture, sturdiness and resilience in time improves and add warmth and coziness to any home. Even though it might be considered rustic and rudimental, in some cases the bold contrast between a modern interior design scheme and a solid piece of wood is to be desired.
Often referred to as Douglas Fir, this wood has a straight, pronounced grain, and has a reddish brown tint to it. Fir is most often used for building; however, it’s inexpensive and can be used for some furniture-making as well. It doesn’t have the most interesting grain pattern and doesn’t take stain very well, so it’s best to use it only when you intend to paint the finished product. Douglas fir is moderately strong and hard for a softwood, rating 4 on a scale of 1 to 4.
You’ll need a long screwdriver with a square blade that is very heavy duty. This gives you a lot of torque. You’ll also need a small and medium slot screwdriver. For working on cabinets or tight places in woodworking, you’ll need a screwdriver with a thin shank so that you can reach screws that are inside of deep holes. This is accomplished with a cabinet screwdriver. Get a couple of medium Phillips head screwdrivers, and a stubby one too, for those tight places. You may also want a ratcheting screwdriver.
I needed a new coffee table for the living room and this design fit the bill perfectly. I came across a table from Ana-White.com that I loved, but modified it a bit because I wanted a breadboard style top. To see her plans click here. The difference between the table in this post is that I cut the top pieces to 41″ (vs 52″) and added the 2×6 pieces to each end, making it come to 52″ with a breadboard style top.
Doesn’t this table look exquisite? It’s a bit surprising to find out that it’s a DIY piece and that you could make something just as awesome without too much effort. You need some MDF, wooden tapered legs, angle top hardware plates, a jigsaw, a screwdriver and spray paint. The trickiest part is cutting the MDF board and giving it the desired shape. Luckily, there’s a tutorial on thewonderforest which can give you some pointers.

All Certification is available to purchase through the Alison Shop. For more information on purchasing Alison Certification, please visit our faqs. If you decide not to purchase your Alison Certification, you can still demonstrate your achievement by sharing your Learner Record or Learner Achievement Verification, both of which are accessible from your Dashboard. For more details on our Certification pricing, please visit our Pricing Page.
The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.
A layout square, or combination square, comes in 6” and 12” sizes. Most woodworkers use the 6” model, simply because it’s easiest to carry around. Also, most of the stock you’ll use will be no bigger than 6” wide, so 12” is overkill. The layout square is a triangle that you can use to mark square cuts on stock. Once you measure the length of the cut, you line up the layout square with the edge of the board. The short side will give you a straight, square cut across the end grain. You can also measure off angles with the layout square. This helps when you’re trying to measure for a bevel on a table saw, or marking a cut for a miter saw. You can even use your layout square to determine an existing angle. Just be sure to buy one made of metal. The plastic ones are not only fragile, but they also can warp, making them pretty useless.
I’m currently working on a dining room table with this color in mind (I also plan on a coffee table soon). I’ve been testing out stain colors and dark walnut is currently in the lead. I love the way this coffee table turned out in color. How many coats of stain did you use? Also, did the dark wax make a big difference in color? I was planning on using a satin poly for sealant (mostly because it’s what is most convenient and what I’m accustomed to), but I’m interested in the dark wax after seeing this post. Any recommendations you have are much appreciated.

More than a year ago, before I joined the staff, Megan Fitzpatrick and I talked about an article I wanted to write about lumberyards and the perennial discussion about domestic versus exotic lumber. At the time, I was also working on an interactive map of New York City’s neighborhoods, and I floated the idea of creating a map of local lumberyards that would accompany the article.


The multi-function coffee table creation can assist as a picnic ensemble, coffee table, and storage unit all in one. Spread your creations and reprocess wooden pallets into reasonable pieces you possibly utilize for a long time. Many individual use this type of coffee table their homes for the reason that you can use this table for different purposes. 

A carpenter is someone who builds and repairs residential, commercial, or industrial structures. These structures can range from homes to commercial buildings to roads and can include individual components such as cabinets, staircases, doorframes, building foundations, and much more. And, although you may think that this occupation only requires physical strength and basic technical skills, carpentry actually requires a strong foundation of specialized expertise and experience in order to ensure that all jobs are completed in accordance with local, state, and national building codes.

Convert your Delta Midi-Lathe to a full size Convert your Delta Midi-Lathe to a full size lathe by adding the Delta Midi Lathe Bed Extension. Featuring a modular design so you can connect multiple extensions this extension increases bed length by 25-1/2 in. so you can turn longer spindles. To reduce vibration add 34 lbs. of cast iron ...  More + Product Details Close
1: Table saw in place of a jointer. Any number of tips in previous issues address straightening edges of boards without a jointer. A jointer serves one purpose, but a tablesaw can serve many (just watch your local Craigslist for a decent one to come up.) The thickness planer is unavoidable, but until you can afford one, buy stock in the thickness you need.
Cut 2- 1x6 46" boards, mitered at 45 degrees on each end (measurement is taken on long side). Cut 2- 1x6 17" boards, mitered at 45 degrees on each end (measurement is taken on long side). Drill pocket holes in both ends of each board. Drill several pocket holes (3 or 4) on the INSIDE edges of each board. Spread wood glue on the edges of each board, and sandwich them together, using bar clamps to keep them tight. Using 1 1/4" pocket hole screws, attach the 1x4's together. (see photo on previous step)

From on-time and on-grade products to an unwavering commitment to its customers, Northwest Hardwoods continues to think ahead and lead with high-quality products and approaches to market. The company announced the launch of its new marketing campaign, Lumber Brings Everything to Life at IWF 2018, which unites its two brands – Northwest Hardwoods and the Industrial Timber and Lumber Company (ITL) brand acquired in 2015 – and illustrates the importance, sustainability and natural beauty that lumber holds in each of our daily lives.
×