Once the vinegar solution dries (or if you decided not to do the solution) you can go ahead and stain the project. First use a rag or air compressor to remove any dust from the table. Then use a clean rag to apply the stain of your choice. Don't forget to wear gloves and ventilate the area. Have a brush in your other hand to stain hard to reach areas.
Thank you so much, Fawn!! I think using pocket holes to connect the top boards is a fantastic idea, and we actually did that with the bigger dining room table we did a few weeks ago. For our coffee table, I kind of liked the look of small gaps in between each board… gives it a more rustic look I think! 🙂 Have fun building your table… I’d love to see it! Tag me on Instagram!
Apply glue to the ends of the 1 x 2 End Pieces for the Base and Apron, and then clamp them in place against the inside of the Leg. Position the pieces so that one runs flush with the top edge, and the other sets below the line marked in Step 7. Center both pieces on the leg, and tilt them so that they run parallel to the edge of the Leg. Using a drill/driver and 1¼-inch pocket holes screws, attach the pieces to the Leg. Repeat on the opposite end.

I want to make some wooden boxes and cases, and I haven't done any wood work till now so I don't have any tools and I can't buy the workshop electronic machines which I see in almost every woodworking instructables here (such as drill, lathe, sanding, saw, mitre, buiskit jointer, and all other electronic tools). So I want to begin with simple hand tools.
Before I send you over there, I have two favors to ask of you. First, help us continue to improve the map! This is not a map of every lumberyard, but if you have a local favorite that isn’t listed, please send it along, with your name and a short blurb about why you like the yard. You can email me the listings at [email protected]. A note – if you are an owner or employee of the yard, please indicate that when you submit. I’m not against someone making a case for his or her operation, but I’d like to note it in your blurb. This isn’t a space to advertise your business, it’s a community resource for other woodworkers. I do look at every entry, which is part of why it took this long to get the map together!
Products and systems by Lamello have always been Products and systems by Lamello have always been designed for longevity and reliability. This legendary durability is combined with environmental stewardship in view as strict environmental regulations at our production site in Switzerland ensure that all resources are used with consideration many of them stemming from sustainable husbandry and management. ...  More + Product Details Close 

In the sixty years of woodworking I have found two tools of increasing necessity. One is a band saw. I can do most of my work with a band saw and hand plane. The second tool is a bow saw, or actually several bow saws. They will replace the band saw if required, though they are slow. One I made about twenty years ago has a one and a half inch wide rip blade and is about thirty inches long. I think the blade is from an old industrial band saw blade I picked up and sharpened into a rip saw blade. It works very well on ripping lumber, logs, etc. Though it tires me out to much to use it now.
We are all well aware of the role of a DIY coffee table for a living room which is highly versatile! It is what you need to get first while entertaining some visitors or guests in the living room! The conversations are also to start always by sitting around it! It is seen mostly in the center of the sitting plans! The reason is that all the sitting personages can use it to place their mobile phones, cups, beverage mugs, magazines and other materials over it while they need to get their hands free for the detailed conversations! So this all tells that how utilitarian item a coffee is!
Poplar is one of the less expensive hardwoods. It’s also fairly soft (1 in hardness on a scale of 1 to 5), which makes it easy to work with. Poplar is white with some green or brown streaks in the heartwood. Because poplar is not the most beautiful wood, it’s rarely used in fine furniture, and if it is, it’s almost always painted. Poplar can be a good choice for drawers (where it won’t be seen) because it is stable and inexpensive. You can find poplar at larger home centers, but a lumberyard will have a better selection.

Thread Related Link and Image Guidelines Thread Related Links posted at WOODWEB's Forums and Exchanges should point to locations that provide supporting information for the topic being discussed in the current message thread. The purpose of WOODWEB Forums is to provide answers, not to serve as an advertising venue. A Thread Related Link that directs visitors to an area with inappropriate content will be removed. WOODWEB reserves the right to delete any messages with links or images it deems inappropriate. (return to form)


The most common type of cedar is the western red variety. Western red cedar, as its name implies, has a reddish color to it. This type of wood is relatively soft (1 on a scale of 1 to 4), has a straight grain, and has a slightly aromatic smell. Western Red cedar is mostly used for outdoor projects such as furniture, decks, and building exteriors because it can handle moist environments without rotting. Western red cedar is moderately priced and can be found at most home centers.

For someone just beginning to purchase hardwood lumber, lumber grades can be overwhelming. Most lumber companies use the generally accepted grading rules set by the National Hardwood Lumber Association. Grades are based on the amount of usable clear material in a board. The highest grade boards are FAS and Select, followed by #1 Common and #2 Common. What grade you choose depends on your project. Some projects, such as tabletops and high quality furniture, may dictate the highest grade available. Many other projects are just as easily adapted to #1 Common (often referred to as cabinet grade) – kitchen cabinet doors, smaller projects and items where some character is acceptable.


In this step take your 2×2 rails that are 41″ long and drill  2 pocket holes on each end using a Kreg Jig. Then take 2 1/2 kreg screws and attach the side rails to each 2×4 end piece. Measure 2 1/4 inches up from the bottom to hang your lower 2×2 rail. Note that in the photo my pocket hole screws are pointing inward. The top rail's pocket holes can face inside the table or to the ground. No matter what they won't be seen. Make sure to have the lower rail's pocket holes facing the floor so you'll be able to attach the shelf to them later.
The next hand tool every woodworker should have is a nail set. In fact, you should have several sizes. They look like awls, and you use them to drive nail heads into the wood so they are flush or right below the surface. This allows you to fill the holes and prepare for staining or painting. The nail setter will usually have either a convex or concave surface to grip the nail better and keep it from sliding off and marring the wood.
India has a long history of fine hand made workmanship so you are in the right place for learning that, unless it has become a vanishing art. I would ask around and see if someone might be able to let you be around them and learn so you can get an idea of what is needed and also some of the tools you might need. Who knows, once you get involved you might decide you like it enough that you could apprentice with someone.
The next hand tool every woodworker should have is a nail set. In fact, you should have several sizes. They look like awls, and you use them to drive nail heads into the wood so they are flush or right below the surface. This allows you to fill the holes and prepare for staining or painting. The nail setter will usually have either a convex or concave surface to grip the nail better and keep it from sliding off and marring the wood.
Certain species of wood have traditionally been associated with different styles of furniture. The wood of choice for the Arts & Crafts movement was quarter sawn white oak, valued for its appearance, durability and dimensional stability. An Arts & Crafts style piece executed in maple might be a well-made example of a classic style, but the choice of wood would be visually at odds with the design. Pine and other softwoods impart a more relaxed, country influence, while traditional hardwoods, such as cherry and walnut, are more likely to be associated with fine furniture.
I consider this my “basic” tool list. Although I do not have a dedicated box for these tools, I assure you that they have a great home in cabinets, on shelves, and laying around on benches. When I do need to take my hand tools somewhere, the larger tools end up in a simple tongue and grooved latch box my grandfather owned. The smaller tools are always in my overall pockets. Overalls work great. They have multiple pockets, they’re comfortable, and they protect your upper body and legs. You only have to deal with small chunks of wood getting into the pockets, which can be dealt with if you or your other half are crafty enough to sew some flaps. It doesn’t bother me though. Thanks for your time.

The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.


Lots of good comments! I do think it is a bit of stretch to include a jointer and surface planner on the ‘basics’ list – we’ve got a slippery slope here! And a lot of different approaches – money, space, time, resources, etc. But lets plunge ahead. If you buy your wood already (or mostly) prep’ed, then the jointer & surface planner can be postponed. You definitely need a way to accurately measure linear distances (e.g. length, width) so a good ruler and tape measure. You need to be able to measure squareness – so you need a good combination square. You need to be able to mark the wood – so a good marking knife, an awl, some chalk, a fine pencil, etc. You should have some decent chisels (and good ones don’t need to cost a lot!). You will need to sharpen them (again not expensive – piece of plate glass and some sandpaper). You need a way to accurately cut your wood – a couple of good handsaws and a file or two for sharpening. You really should have a decent work surface/work bench/etc – a good first project by the way. Last of the basics – a good drill (3/8″ vs battery type). Lastly (I could go on but room is lacking), take a look at Paul Seller’s video’s for simple but highly competent work. 

If you have already completed some college or university education, then many apprenticeship programs will give you credit for prior learning. You can even receive credit for work experience you possess in the construction field. It is important to note that any education and work experience credits will likely be evaluated on a case-by-case basis, so if you want to explore this option, then checking around for the best use of your experience is key.
The course was fantastic and exceeded my expectations so much that I then booked the second week plumbing course covering domestic hot water systems. Again the centre and staff were excellent and I then booked a third week to take advantage of their ‘4 for 3’ offer so I’ve now done the tiling and carpentry courses. All staff at Yta are so friendly and helpful and I will be recommending the courses to all my friends and family. I will definitely be returning to book more courses and that seemed to be the thinking of other students also. Fantastic training centre! I wish there was an option for more than 5 stars! They deserve it.

Advertising:   The purpose of WOODWEB Forums is to provide answers, not an advertising venue. Companies participating in a Forum discussion should provide specific answers to posted questions. WOODWEB suggests that businesses include an appropriately crafted signature in order to identify their company. A well meaning post that seems to be on-topic but contains a product reference may do your business more harm than good in the Forum environment. Forum users may perceive your references to specific products as unsolicited advertising (spam) and consciously avoid your web site or services. A well-crafted signature is an appropriate way to advertise your services that will not offend potential customers. Signatures should be limited to 4-6 lines, and may contain information that identifies the type of business you're in, your URL and email address (return to top).
Loveland lies in Larimer county, which is one of the 55 counties in Colorado. Overall, the Fort Collins-Loveland area has 128,650 total employed workers according to the US Bureau of Labor Statistics, with a 2% unemployment rate, $21/hr average worker wage, and a $43,210 average annual salary. Thus, about 6 out of every 1000 jobs in Loveland are held by carpenters, and 6/1000 are held by construction laborers.
I built my coffee table!! I used the plans at www. EasyWoodwork.org to build mine – highly recommended you check those out too. They are detailed and super easy to read and understand unlike several others I found online. The amount of plans there is mind-boggling… there’s like 16,000 plans or something like that for tons of different projects. Definitely enough to keep me busy with projects for many more years to come haha
Problems donating? | Other ways to give | Frequently asked questions | We never sell your information. By submitting, you are agreeing to our donor privacy policy. The Wikimedia Foundation is a nonprofit, tax-exempt organization. If you make a recurring donation, you will be debited by the Wikimedia Foundation until you notify us to stop. We'll send you an email receipt for each payment, which will include a link to easy cancellation instructions.
In this article, I have described some most important coffee table woodworking projects. There are numerous coffee table woodworking projects available in the market. Some significant table may include a rustic coffee table, the beverage pallet coffee table, modern pallet coffee table, glass topped coffee table, storage coffee table plans, apothecary coffee table, multi-function coffee table, wine crate coffee table, concrete coffee tables and sturdy coffee table. You can use these coffee tables for different purposes such as for home or shop.
Real quick story: Recently, I had to help my brother with some furniture and cabinet issues, but there were a few problems. First he lived 3 hours by car and my wife needed our only car. I’ve had a scooter for a few years, but have only used it for local trips with small needs. Since weather was changing and I needed a break away from my other half, I decided to make the trip. I installed my motorcycle saddlebags to the scooter and loaded the necessary tools for the trip. Where’s the motorcycle? That’s another story. Of course the saddlebags are small and the scooter only had a massive 50cc engine; vrmm, vrmm. Although I have a shop full of electric and traditional hand tools, only the smaller hand tools would make the list for this trip. So, here is the list from that trip: (A few may be missing)
A quality wood moisture meter is vital to the long-term success of any woodworking project you put together. Lumber mills try to dry their batches of lumber according to the intended end product destination. That is, if the wood is harvested in the wet Northeast, but is going to be shipped to the arid Southwest, it will be dried more than wood kept in the Northeast for use by woodworkers. The success of your woodworking project, from wood flooring to kitchen cabinets to fine furniture, depends on the correct moisture content levels of the woods you use for your area of the country.

More than a year ago, before I joined the staff, Megan Fitzpatrick and I talked about an article I wanted to write about lumberyards and the perennial discussion about domestic versus exotic lumber. At the time, I was also working on an interactive map of New York City’s neighborhoods, and I floated the idea of creating a map of local lumberyards that would accompany the article.


As someone who is just progressing past being a “beginner” (just getting into building furniture) in the woodworking community, I would say there are a number of changes I would make to your list. First, I would say that a power jointer/thicknesser does not belong on the list by any means. They are way too large of an investment and take up a lot of space (not to mention you can buy your stock at the desired dimensions). I also strongly disagree with the concept of joinery devices. As someone new to the trade, I feel this is a very important skill that must be developed, not skipped over by buying devices power devices that achieve a single goal. I think the jigsaw should be replaced by a good bandsaw. I just purchased my first major power tool and it was a 14″ bandsaw and not a tablesaw for space reasons as well as versatility. The bandsaw allows me to resaw, cut curves, (now that it is adjusted for drift) rip pieces of stock accurately that are thicker than a table saw could handle, etc. Once the cut is complete, a handplane can remove any saw marks and square/flatten a surface. It is also really useful for cutting tenons and dovetails. Handsaws can be used for crosscutting and anything else the bandsaw cannot handle. As for a bench, if you are getting into woodworking, this should be your first real project (and it is not expensive to make). You are also missing a good vise to be attached to the bench.
You can make a coffee table stand out and be interesting from an aesthetic point of view without complicating its design too much. These plans from Abeautifulmess are a perfect example in that sense. This wooden coffee table definitely has what it takes to become a focal point for the living room and to serve as a statement piece for the entire space. Its design is a combination of sculptural and geometric beauty and a contrast between the solid and heavy top and the sleek and delicate hairpin legs.
The plan I’m using is a modified version of a table from Shabby Creek Cottage, and mine came out to be a whopping 46 1/2″ x 38 1/2″. It’s big, beautiful, and a perfect fit for our space, but if you don’t need a massive table like this one, you can either: make adjustments to these plans OR check out Gina’s table, which is quite a bit smaller. Okay, let’s build!
A Guide to Honing and Sharpening helps woodworkers keep their tools in the best possible working condition. It focuses on the history of honing and sharpening and vital aspects of these practices, such as stropping, beveling, chiseling, flattening and other modern technological methods. Students can explore these methods via text, pictures and diagrams.
Like wooden pallets, the coffee table wine crates are a delightful resource for creating a table from scratch. All that is compulsory in four crates and wheels set if needed. Utilize the central space occasioned from the rates merging to show your beautiful flower vase or candle holder. Therefore, wine crate coffee table is a good woodworking project.
For over 50 years, American Lumber has earned its reputation for quality, service and dedication to innovation in the hardwood lumber industry. We combine years of hardwood lumber and hardwood log experience with technology and resources to help our customers succeed. Today we provide almost all of the North American hardwood lumber species including red and white oak, ash, cherry, poplar, maple, hickory, alder and walnut. However, we are not just American anymore! We are also a premier provider of imported hardwood lumber from South America, Africa, and Asia...Read More
For someone just beginning to purchase hardwood lumber, lumber grades can be overwhelming. Most lumber companies use the generally accepted grading rules set by the National Hardwood Lumber Association. Grades are based on the amount of usable clear material in a board. The highest grade boards are FAS and Select, followed by #1 Common and #2 Common. What grade you choose depends on your project. Some projects, such as tabletops and high quality furniture, may dictate the highest grade available. Many other projects are just as easily adapted to #1 Common (often referred to as cabinet grade) – kitchen cabinet doors, smaller projects and items where some character is acceptable.
Teak is becoming rarer as the days go on, but it is the staple for fine outdoor furniture. Teak is highly weather-resistant and beautiful (not to mention expensive — can you believe almost $24 a board foot?). Teak has an oily feel and a golden-brown color. It rates a 3 on a scale of 1 to 5 for hardness and is only available from larger lumberyards and specialty suppliers.

However, if you want to stain or clear-coat the project, you'll have a number of choices to look through. Since your local home center megamart will probably only carry a couple of hardwood species (poplar and red oak are common) spend time at a fine wood supplier and look through the vareties available. They should be able to help you determine how each species will look when finished, which will go a long way toward refining your decision.


Our team at Hermance is seasoned in many years of experience and specially trained to ensure we're able to quickly assist you in finding the right product to meet your needs. In business for over 100 years, Hermance knows wood working equipment top to bottom. Check us out today and see why we're the top choice when it comes to new woodworking machinery. Contact us to learn more about our general woodworking machinery today.
There are no formal education or training requirements to become a carpenter in the U.S., but the BLS reports that three to four years of experience is the industry standard for becoming a skilled craftsperson. Training and experience can be acquired by working with an experienced journeyman or through an apprenticeship offered by an employer or labor union. Formal in-class instruction is offered through certificate, diploma or associate's degree programs in carpentry at trade or vocational schools. Employees with some formal carpentry education generally start at higher positions in the field. Carpentry courses may include carpentry math, building layouts, foundation work, roofing, stair construction, siding and moldings. You can also study interior and exterior finishes.

Thanks for the feedback. We’re glad you found the list helpful. Please note that this page contains only 10 of the 40 top tools for woodworking, displaying only hand tools. You can find the next 10 here: https://www.wagnermeters.com/top-40-woodworking-tools-2/. There are links at the bottom of each article to the next group of tools so you can view the entire list. Hope this helps.
If you have already completed some college or university education, then many apprenticeship programs will give you credit for prior learning. You can even receive credit for work experience you possess in the construction field. It is important to note that any education and work experience credits will likely be evaluated on a case-by-case basis, so if you want to explore this option, then checking around for the best use of your experience is key.
Hi Alex! I usually only do one coat of stain for darker colors like Dark Walnut. The dark wax doesn’t make a huge difference in the color since the stain is already pretty dark, but I like using wax on furniture to give it more of a natural finish versus a poly. For pieces that get used and abused heavily (like our dining room table) I use a matte finish poly, but for the coffee table wax worked just fine. I hope this helps!
Hands-on techniques are generally introduced in this course, which covers exterior moisture, interior and exterior doors, window trim installation and custom built-in cabinetry. When studying interior finish features, students learn about sheet rock, taping and texturing and cabinet installation. Coursework on exterior finish features may include estimating time and costs, framing, laying out rafters for roofs and installing outside doors and windows. This course is taken after introductory courses.
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking.   These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email orderdesk@canadianwoodworking.com  and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence. 
Creativity knows no limits and this chicken coop coffee table proves it. It’s something that we found on findinghomefarms. It’s a one-of-a-kind piece with lots of character, the type of table that makes a statement no matter where you put it. Of course, such a daring and unusual project is not exactly very versatile so you’d need a certain type of decor to make it fit.

Even though this is in fact a side table, we can definitely find inspiration in its design. We find this project to be highly creative and interesting. The table has a hexagon-shaped top and bottom connected by two sets of five rods. Two in each set are longer than the other and go through the bottom hexagon, acting as legs. You can find the plans for this project on ohohblog.
Description: In this session, I will be demonstrating over 20 ways to mount wood on the lathe for turning. Starting with different methods between centers, I will demonstrate single axis, as well as multi-axis turning. Discussion will then move to various ways to use faceplates, to safely hold your wood blank on the lathe. We will then progress to scroll chucks and screw center usage. Next, will be conversation on the use of homemade chucks, jam chucks, collets and mandrels. I will then demonstrate the use of vacuum chucks, jumbo jaws, doughnut chucks, and Longworth style chucks, and finish up with the use of various types of steady rests, including ring-style, bowl steadies, and spindle supports. This class is geared toward the turner who is interested in learning many different ways to mount pieces of wood in the lathe, and what the advantages or disadvantages might be of different techniques. The student will be expected to watch and learn, but also get involved in the discussion regarding chucking methods, and share some of their experiences as well. This class is designed for all turners, wanting to learn. Please bring eye protection to class.
We really like the distressed look on this coffee table. There are a few ways in which you can achieve that. You can use reclaimed wood or you can create the antiqued finish artificially using special techniques. You can analyze the plans and the instructions shared on instructables to find out more about this strategy. They also show you how to build this stylish pinstripe table.
Coffee tables are from the wide variety of furniture pieces one requires to furnish his home the least taken into consideration from the beginning of the design process.They are often overlooked or taken for granted as pieces not really necessary for the comfort of the home. But despite this initial belief, the coffee table will later on turn out to be a vital element in the proper functionality of a living room as well as small balcony that is used as a coffee break time. The proper coffee table will complete your interior design, will organize and rank your furniture around it, whilst setting the focus of the room to a perfectly positioned key element.
The oak contrast coffee table is pretty popular in these days. The natural oak has a beautiful texture that must be put to the worth by making bold contrasts among the oak top and the other body of the table. There is numerous table in the market for sell because of many individuals like this these tables and want to purchase oak contrast coffee table.
Once the mixture is made, simply brush the solution on the wood. It won't immediately turn colors, but over a few hours you'll notice a considerable difference. Check out the photos of my farm table project to see how well it worked using fir boards. You'll notice the fir 2×2's used in this project really took the solution well. The other boards had a little coloring and grain enhancement, but white pine doesn't have many tannins in it so it is less reactive.

Additionally, working with a contractor or construction company allows students to gain hands-on experience that's virtually imperative for future employment. High school graduates may advance to apprenticeship, vocational, or technical programs. Generally, training to become a skilled carpenter requires 3-4 years of on-the-job instruction and formal education (either in person or through online carpenter school).
Wood tends to rise its general quality and character with the time passage. I would like to say that water wind rain snow possibly transform its porosity and texture and make it more attractive for a table piece. The attractiveness of this coffee table is the reason behind its mostly utilization. So, you can keep in mind this table as an excellent table.

Maple comes in two varieties: hard and soft. Both varieties are harder than many other woods; hard maple is so hard (a 5 on a scale of 1 to 5) that it’s difficult to work with. Soft maple, on the other hand, is relatively easy to work with. Because of their fine, straight grain, both varieties are more stable than many other woods. They also tend to be less expensive than other hardwoods. You won’t find maple at your local home center, but most lumberyards have a good selection of it.
Lumber for your projects can come from many sources, but before you can use it to build anything, it must be dry. Lumber that is kiln dried will have a moisture content right out of the kiln of 7 or 8%. However, by the time the lumber is delivered to your local dealer and arrives at your shop, the moisture content may have changed dramatically. Storage conditions between the kiln and your shop are clearly out of your control, so it is always a good idea after purchasing lumber to acclimatize it in your shop for several weeks. To avoid using lumber that is still in the process of adjusting to its new environment it is best to use a moisture meter to verify the moisture content of the wood. Most dealers don't mind customers checking the moisture content at the yard as long as they are using a pinless meter. The meter in my lumber kit uses electromagnetic waves to calculate the moisture content of a given piece of wood. Its use couldn't be simpler or quicker – simply turn it on, enter the species, and place the meter on the wood to be measured. The result is displayed right on the screen instantly without the need for conversion tables and other calculations. Typically, I check a couple of areas on each board as I select them just to confirm they are all in the same moisture range. Back at the shop I once more check each piece of wood and note it in chalk on the board. Every few days I'll recheck the boards, and when the readings have stabilized, I can be reasonably certain there won't be any surprises when I start the milling process.
Searching for discount wood crafting tools? DHgate.com offers 277 wood crafting tools products. Our online stores provide a wide selection of tpms tool ford at discount prices. You can also choose from discount Other, Jewelry Tools & Equipment, Jewelry as well as from discount Loupes, Magnifiers, Tweezers, Pick-Up Tools, and Rotary Tools & Accessories. You will be fascinated by our excellent mileage correction tool for cars 2018 with exquisite crafts and fast delivery. Don't miss our time limited daily tool rails deals!

Certain species of wood have traditionally been associated with different styles of furniture. The wood of choice for the Arts & Crafts movement was quarter sawn white oak, valued for its appearance, durability and dimensional stability. An Arts & Crafts style piece executed in maple might be a well-made example of a classic style, but the choice of wood would be visually at odds with the design. Pine and other softwoods impart a more relaxed, country influence, while traditional hardwoods, such as cherry and walnut, are more likely to be associated with fine furniture.
From on-time and on-grade products to an unwavering commitment to its customers, Northwest Hardwoods continues to think ahead and lead with high-quality products and approaches to market. The company announced the launch of its new marketing campaign, Lumber Brings Everything to Life at IWF 2018, which unites its two brands – Northwest Hardwoods and the Industrial Timber and Lumber Company (ITL) brand acquired in 2015 – and illustrates the importance, sustainability and natural beauty that lumber holds in each of our daily lives.
×